« previous next »
Pages: [1]   Go Down

Author Topic: 1000cc again  (Read 1667 times)

0 Members and 1 Guest are viewing this topic.

Offline Big Jay

  • Expert
  • ****
  • Posts: 1,252
    • CBRzone
1000cc again
« on: May 15, 2012, 11:38:33 PM »
Getting ready to do another run of the 1000cc piston kits and perhaps 970 too .rying to gauge intrest.

Post it up if you are interested in a set of either.

Logged

Offline turboguzzi

  • Old Timer
  • ******
  • Posts: 4,085
Re: 1000cc again
« Reply #1 on: May 16, 2012, 01:06:20 AM »
hi jay

another subject, but check your pm's

TG
Logged

Offline madmtnmotors

  • When did I get to be a
  • Really Old Timer ...
  • *******
  • Posts: 6,090
  • Sunny Central Florida
Re: 1000cc again
« Reply #2 on: May 16, 2012, 04:23:19 AM »
Are these designed to work with the stock jugs? I see the sleeves in the photo, just checking to see whether custom cylinder block is needed. Looking good!  8)
Logged
TAMTF...


Wilbur



Projects:
"Evolution": http://forums.sohc4.net/index.php?topic=100352.0
"P.O. Debacle": http://forums.sohc4.net/index.php/topic,126692.msg1441661.html#msg1441661
F2/F3 O-rings: http://forums.sohc4.net/index.php?topic=113672.msg1300721#msg1300721
Cam Tower Studs: https://www.mcmaster.com/#93210a017/=t19sgp
Clean up that nasty harness: http://forums.sohc4.net/index.php?topic=137351.msg1549191#msg1549191
http://forums.sohc4.net/index.php/topic,148188.msg1688494.html#msg1688494
http://forums.sohc4.net/index.php/topic,139544.msg1579364.html#msg1579364
                                          
Charging system diagnosis: http://forums.sohc4.net/index.php?topic=1012.msg8345#msg8345
Get the manuals: http://manuals.sohc4.net/cb750k/
The Dragon: http://forums.sohc4.net/index.php?topic=45183.msg1571675#msg1571675
Headlight Switch: http://forums.sohc4.net/index.php?topic=113986.msg1283236#msg1283236
Branden's leak free top end thread: http://forums.sohc4.net/index.php?topic=107040.0
Engine Lifting Made Easy: http://forums.sohc4.net/index.php/topic,58210.msg1684742.html#msg1684742
                                      http://forums.sohc4.net/index.php/topic,100352.msg1675840.html#msg1675840
Static and Dynamic Timing: http://www.hondachopper.com/garage/carb_info/timing/timing1.html
Airbox Gasket Replacement: http://forums.sohc4.net/index.php/topic,114485.msg1290000.html#msg1290000
"Café" : http://forums.sohc4.net/index.php/topic,84697.msg953814.html#msg953814
PD Carb Choke Linkage: http://forums.sohc4.net/index.php/topic,100352.msg1669248.html#msg1669248
                                    http://forums.sohc4.net/index.php/topic,110931.msg1248354.html#msg1248354
                                    http://forums.sohc4.net/index.php/topic,48858.msg515204.html#msg515204
Follow up on your damn posts: http://forums.sohc4.net/index.php/topic,144305.msg1791605.html#msg1791605
Taiwanese Cam Chain Tensioners:  http://forums.sohc4.net/index.php/topic,155043.msg1774841.html#msg1774841
Gumtwo Seat Cover: http://forums.sohc4.net/index.php/topic,164440.msg1897366.html#msg1897366
Primary Drive: http://forums.sohc4.net/index.php/topic,166063.msg1919278.html#msg1919278
Tank Latch: http://forums.sohc4.net/index.php/topic,165975.msg1919495.html#msg1919495
Shorten your forks: http://vintage-and-classic-honda-s.456789.n3.nabble.com/How-to-shorten-forks-td4042465.html DO NOT CUT THE SPRINGS!
Clutch How To: http://vintage-and-classic-honda-s.456789.n3.nabble.com/How-to-change-and-adjust-a-clutch-SOHC-td4040391.html
Late model K7/K8/F2/F3 front sprocket cover removal: http://forums.sohc4.net/index.php/topic,178428.msg2072279.html#msg2072279
630 to 530 conversion: http://forums.sohc4.net/index.php/topic,180710.msg2094423.html#msg2094423

Sent from my Tandy TRS-80!

Offline Big Jay

  • Expert
  • ****
  • Posts: 1,252
    • CBRzone
Re: 1000cc again
« Reply #3 on: May 16, 2012, 11:13:41 AM »
Stock blocks
Logged

Offline spiritof67

  • Hot Shot
  • ***
  • Posts: 338
Re: 1000cc again
« Reply #4 on: May 16, 2012, 05:54:04 PM »
Ah, the 1000cc Big Dream!

What nominal compression? Peened stock rods OK, or "big man" ones needed? And do you mill the edge of the combustion chamber "cap" to get the sharp edge off, or leave it as a "squish"?

Spirit

1000cc - the memory of Japauto, Henry Abe and many more! TORQUE!
Logged
Pages: [1]   Go Up
« previous next »