« previous next »
Pages: [1]   Go Down

Author Topic: leaking front caliper  (Read 961 times)

0 Members and 2 Guests are viewing this topic.

Offline millerza

  • Zach Miller
  • Enthusiast
  • **
  • Posts: 148
  • 750K8 fixing rebuild probs
leaking front caliper
« on: May 23, 2012, 06:42:41 PM »
78k 750 so after rebuild my front caliper started leaking, figured it was pitting on the piston. Ordered a SS piston and thought it was going to be good. So I put it on and rode a bit no leak. A day later I looked at it and the mother f'er was leaking again. What gives?
Logged

Offline TwoTired

  • Really Old Timer ...
  • *******
  • Posts: 21,805
Re: leaking front caliper
« Reply #1 on: May 23, 2012, 06:57:41 PM »
New seal?

Read the Brake FAQ?

Cleaned the seal groove?
Logged
Lloyd... (SOHC4 #11 Original Mail List)
72 500, 74 550, 75 550K, 75 550F, 76 550F, 77 550F X2, 78 550K, 77 750F X2, 78 750F, 79CX500, 85 700SC, GL1100

Those that learn from history are doomed to repeat it by those that don't learn from history.

Offline madmtnmotors

  • When did I get to be a
  • Really Old Timer ...
  • *******
  • Posts: 6,090
  • Sunny Central Florida
Re: leaking front caliper
« Reply #2 on: May 23, 2012, 07:01:24 PM »
Make sure it's not wicking from the bleeder screw or the flare connection where the hard line connects to the caliper. The fluid can "wick" to a location other than where the actual leak is originating from and can be hard to detect without a very close inspection. Wipe everything off and check often for signs of fluid.
Logged
TAMTF...


Wilbur



Projects:
"Evolution": http://forums.sohc4.net/index.php?topic=100352.0
"P.O. Debacle": http://forums.sohc4.net/index.php/topic,126692.msg1441661.html#msg1441661
F2/F3 O-rings: http://forums.sohc4.net/index.php?topic=113672.msg1300721#msg1300721
Cam Tower Studs: https://www.mcmaster.com/#93210a017/=t19sgp
Clean up that nasty harness: http://forums.sohc4.net/index.php?topic=137351.msg1549191#msg1549191
http://forums.sohc4.net/index.php/topic,148188.msg1688494.html#msg1688494
http://forums.sohc4.net/index.php/topic,139544.msg1579364.html#msg1579364
                                          
Charging system diagnosis: http://forums.sohc4.net/index.php?topic=1012.msg8345#msg8345
Get the manuals: http://manuals.sohc4.net/cb750k/
The Dragon: http://forums.sohc4.net/index.php?topic=45183.msg1571675#msg1571675
Headlight Switch: http://forums.sohc4.net/index.php?topic=113986.msg1283236#msg1283236
Branden's leak free top end thread: http://forums.sohc4.net/index.php?topic=107040.0
Engine Lifting Made Easy: http://forums.sohc4.net/index.php/topic,58210.msg1684742.html#msg1684742
                                      http://forums.sohc4.net/index.php/topic,100352.msg1675840.html#msg1675840
Static and Dynamic Timing: http://www.hondachopper.com/garage/carb_info/timing/timing1.html
Airbox Gasket Replacement: http://forums.sohc4.net/index.php/topic,114485.msg1290000.html#msg1290000
"Café" : http://forums.sohc4.net/index.php/topic,84697.msg953814.html#msg953814
PD Carb Choke Linkage: http://forums.sohc4.net/index.php/topic,100352.msg1669248.html#msg1669248
                                    http://forums.sohc4.net/index.php/topic,110931.msg1248354.html#msg1248354
                                    http://forums.sohc4.net/index.php/topic,48858.msg515204.html#msg515204
Follow up on your damn posts: http://forums.sohc4.net/index.php/topic,144305.msg1791605.html#msg1791605
Taiwanese Cam Chain Tensioners:  http://forums.sohc4.net/index.php/topic,155043.msg1774841.html#msg1774841
Gumtwo Seat Cover: http://forums.sohc4.net/index.php/topic,164440.msg1897366.html#msg1897366
Primary Drive: http://forums.sohc4.net/index.php/topic,166063.msg1919278.html#msg1919278
Tank Latch: http://forums.sohc4.net/index.php/topic,165975.msg1919495.html#msg1919495
Shorten your forks: http://vintage-and-classic-honda-s.456789.n3.nabble.com/How-to-shorten-forks-td4042465.html DO NOT CUT THE SPRINGS!
Clutch How To: http://vintage-and-classic-honda-s.456789.n3.nabble.com/How-to-change-and-adjust-a-clutch-SOHC-td4040391.html
Late model K7/K8/F2/F3 front sprocket cover removal: http://forums.sohc4.net/index.php/topic,178428.msg2072279.html#msg2072279
630 to 530 conversion: http://forums.sohc4.net/index.php/topic,180710.msg2094423.html#msg2094423

Sent from my Tandy TRS-80!

Offline millerza

  • Zach Miller
  • Enthusiast
  • **
  • Posts: 148
  • 750K8 fixing rebuild probs
Re: leaking front caliper
« Reply #3 on: May 23, 2012, 09:11:40 PM »
two new seals, no luck. Could probably have cleaned groove better.  I have thought of leak from another location but really appears from puck. I will try to clean groove though.
Logged

Offline MCRider

  • Such is the life of a
  • Really Old Timer ...
  • *******
  • Posts: 14,376
  • Today's Lesson: One good turn deserves another.
Re: leaking front caliper
« Reply #4 on: May 23, 2012, 09:48:43 PM »
Quote from: millerza on May 23, 2012, 09:11:40 PM
two new seals, no luck. Could probably have cleaned groove better.  I have thought of leak from another location but really appears from puck. I will try to clean groove though.
Its only a few places: Input line, bleeder valve or the piston seal.

I haven't finished mine yet and they weren't leaking. But they wouldn't retract. I disassembled them and the new seals (Square cross section O Rings) wern't the right size! See if your new ones fit snug to the piston first, then install.

I used the soft bristle brush with my Dremel to clean the grooves.
Logged
Ride Safe:
Ron
1988 NT650 HawkGT;  1978 CB400 Hawk;  1975 CB750F -Free Bird; 1968 CB77 Super Hawk -Ticker;  Phaedrus 1972 CB750K2- Build Thread
"Sometimes the light's all shining on me, other times I can barely see, lately it appears to me, what a long, strange trip its been."
Pages: [1]   Go Up
« previous next »