Author Topic: Engine leaking oil.. (Read 3847 times)

messeduptriple · « **on:** June 08, 2012, 03:47:54 pm »

I finally got the 550 to run perfect. Idles well, and sounds great. I plugged the tach that was leaking oil with an aftermarket spike plug from ebay. That is no longer leaking but I still have a good amount of oil coming out somewhere from the upper front engine. When it idles it doesn't leak but when I hop on the highway it's leaking, I can't seem to see where though. I stopped and looked but seems to be in the front somewhere. I cant see any cracks major and have no idea where to go from here. How can I check now? Should I use some engine oil sealer from fleet farm?? Any help would be great.

Sent from my MB855 using Tapatalk 2

messeduptriple · « **Reply #1 on:** June 08, 2012, 03:50:31 pm »

Sent from my MB855 using Tapatalk 2

messeduptriple · « **Reply #2 on:** June 08, 2012, 03:54:22 pm »

Sent from my MB855 using Tapatalk 2

goldarrow · « **Reply #3 on:** June 08, 2012, 04:18:37 pm »

I don't have whole lot of expertise on this but from what I have read from other posts : top end rubber seals and gaskets may need to be inspected or replaced, or live with it if the leaks are minimal. Check oil level regularly though. Someone please chime in if I'm wrong. Hope this helps.

bollingball · « **Reply #4 on:** June 08, 2012, 04:45:16 pm »

Engine oil sealer. I wonder what that would do to your clutch want to take a guess?

Ken

messeduptriple · « **Reply #5 on:** June 08, 2012, 04:49:01 pm »

I just cant seem to find out where all the oil is coming from.

Sent from my MB855 using Tapatalk 2

ekpent · « **Reply #6 on:** June 08, 2012, 05:04:01 pm »

Some guys will clean and degrease the engine and then when dry sprinke baby or talcum powder or such around on the engine.Start it up. When the oil first starts to leak the powder gets wet making the spot easier to identify. May be worth a shot.Won't work going down the highway though.

LesterPiglet · « **Reply #7 on:** June 08, 2012, 05:05:22 pm »

Clean and degrease the engine. Cover the engine with talcum powder. Take it for a short spin. This should show up the leaks.
Don't forget to wear a funny hat.

ekpent beat me to it.

DJ_AX · « **Reply #8 on:** June 08, 2012, 05:08:40 pm »

foot powder in an aerosol can works great

matt mattison · « **Reply #9 on:** June 08, 2012, 05:15:37 pm »

Did you make sure all the bolts on top of the engine are tight? Don't over tighten them though, the cast aluminum could crack. Try to go by the torque specs in your manual. It's worth a shot.

messeduptriple · « **Reply #10 on:** June 08, 2012, 05:31:03 pm »

I looked after cleaning a bit and found this ...its chipped ..could this be the leak?

Sent from my MB855 using Tapatalk 2

LesterPiglet · « **Reply #11 on:** June 08, 2012, 05:38:28 pm »

If you are referring to the gap at the base gasket that is normal. From your previous pictures the leak looks higher up than that. I'd be looking up the top first. Do the talc test.

I just reread. Check your latest tach cap and also the tappet covers. I found one of mine leaking the other day.

messeduptriple · « **Reply #12 on:** June 08, 2012, 05:45:50 pm »

Nevermind ...cant get the bike to start anymore ... lol ... fml.

Sent from my MB855 using Tapatalk 2

goldarrow · « **Reply #13 on:** June 08, 2012, 05:46:52 pm »

That's the gap for screwdriver to pry off cylinder...not chipped

messeduptriple · « **Reply #14 on:** June 08, 2012, 05:49:49 pm »

I tried to idle it ..reving it and waiting for oil leak ..then decided to spin around the house and park and stopped the bike..couldn't get in neutral so stopped the bike and turned off ..hit neutral now doesn't want to start..sounds like its dead..getting that clickn noise.

Sent from my MB855 using Tapatalk 2

LesterPiglet · « **Reply #15 on:** June 08, 2012, 05:51:00 pm »

Put the battery on charge for a few hours and have some beer.

messeduptriple · « **Reply #16 on:** June 08, 2012, 05:51:52 pm »

* it was only smokn lightly from the right header ...any info on why? I used the heat gun ray and they were all in same temp ..not sure wtf is going on. Im mentally exhausted from this bike now...getting so frustrated ..if not one thing its another. Maybe I shouldn't have done this project.

Sent from my MB855 using Tapatalk 2

LesterPiglet · « **Reply #17 on:** June 08, 2012, 05:54:13 pm »

Burning oil, say from an oil leak, gives off smoke.

So is there oil in the exhaust port then?

messeduptriple · « **Reply #18 on:** June 08, 2012, 06:42:56 pm »

Quote from: LesterPiglet on June 08, 2012, 05:54:13 pm

Burning oil, say from an oil leak, gives off smoke.

So is there oil in the exhaust port then?

I dont know ...should I pull the exhaust off?? I'm gonna try that powder deal tmrw.

Sent from my MB855 using Tapatalk 2

chickenman_26 · « **Reply #19 on:** June 08, 2012, 07:23:30 pm »

Quote from: messeduptriple on June 08, 2012, 03:47:54 pm

When it idles it doesn't leak but when I hop on the highway it's leaking, I can't seem to see where though. I stopped and looked but seems to be in the front somewhere.

If it's not seeping from the valve cover, then it's probably leaking past the rubber pucks that seal the head bolt holes under the valve cover. The oil leaks down and flows into the spark plug wells. From there, the wind distributes it all over the top end. Tightening won't stop it. You'll need to purchase 6 new pucks, and replace them. Make sure the recesses they seat in are clean and dry, and use no sealer of any kind on the pucks. As long as you'll have the valve cover off, you may as well re-torque the head. Don't neglect to replace the valve cover and breather cover seals.

Stu

fergie · « **Reply #20 on:** June 08, 2012, 07:47:47 pm »

Most likely the head gasket/ rubber pucks. If the bike is smoking from one of the pipes you probably have a ring job ahead of you. The head gasket /rubbers pucks commonly leak one old honda fours. sounds like you need to do a engine tear down.

messeduptriple · « **Reply #21 on:** June 09, 2012, 03:30:27 am »

Oh

Sent from my MB855 using Tapatalk 2

messeduptriple · « **Reply #22 on:** June 09, 2012, 03:37:54 am »

Quote from: chickenman_26 on June 08, 2012, 07:23:30 pm

Quote from: messeduptriple on June 08, 2012, 03:47:54 pm
When it idles it doesn't leak but when I hop on the highway it's leaking, I can't seem to see where though. I stopped and looked but seems to be in the front somewhere.
If it's not seeping from the valve cover, then it's probably leaking past the rubber pucks that seal the head bolt holes under the valve cover. The oil leaks down and flows into the spark plug wells. From there, the wind distributes it all over the top end. Tightening won't stop it. You'll need to purchase 6 new pucks, and replace them. Make sure the recesses they seat in are clean and dry, and use no sealer of any kind on the pucks. As long as you'll have the valve cover off, you may as well re-torque the head. Don't neglect to replace the valve cover and breather cover seals.

Stu

this may sound stupid but what are pucks? ??

Sent from my MB855 using Tapatalk 2

Mcwilliams570 · « **Reply #23 on:** June 09, 2012, 05:23:54 am »

The round black things in the pic are pucks...

Matt

messeduptriple · « **Reply #24 on:** June 09, 2012, 05:38:41 am »

Thanks. Do I need to yank the whole engine out? And how do these go bad? I bought it and it didn't do this ...now its doing this leaking.

Sent from my MB855 using Tapatalk 2

News:

Author Topic: Engine leaking oil.. (Read 3847 times)

bollingball