Author Topic: Any interest in MLS head gaskets for CB550's? (Read 7280 times)

MRieck · « **on:** July 12, 2012, 01:52:30 PM »

61mm bore gasket would cover 572cc and 592cc. .010 thick base gaskets?

bwaller · « **Reply #1 on:** July 12, 2012, 08:07:52 PM »

Shall I kiss you on the lips ?

I'll PM a concern after my race weekend.

Cool Deal Mike.

RAFster122s · « **Reply #2 on:** July 12, 2012, 09:28:21 PM »

Well, while I have seen the acronym on the forum a couple time I will have to plead ignorance/buy a clue. I may be interested as well; as I have acquired parts for a 592cc kit for my 550 but need gaskets and figured I would have to go with a copper gasket. ~~Can you point me to info on MLS gaskets?~~ went and googled it, multi-layer steel, a modern headgasket design. Yes, I am interested!
Thanks! David

trueblue · « **Reply #3 on:** July 13, 2012, 04:19:36 AM »

Would I be correct in assuming that this will also fit the 650

sinister902 · « **Reply #4 on:** July 13, 2012, 06:35:11 AM »

I'd be interested in one if it fit a 650 with cb750 liners bored with 836 kit pistons

Kemp · « **Reply #5 on:** July 13, 2012, 07:40:14 AM »

I'm interested as well. Are you ordering a run of these gsts and what would be the cost.

Mr Johann Vegas · « **Reply #6 on:** July 19, 2012, 10:48:57 AM »

Mike,
I'd be interested.

RAFster122s · « **Reply #7 on:** September 01, 2012, 12:28:34 AM »

Mike put me down for two if they aren't going to cost an arm and a leg...

MRieck · « **Reply #8 on:** September 01, 2012, 06:39:43 AM »

They are in the works guys.

FunJimmy · « **Reply #9 on:** September 01, 2012, 08:32:21 AM »

I need a couple too, Mike.

Thanks
FJ

FunJimmy · « **Reply #10 on:** September 27, 2012, 05:16:27 PM »

Any development on these Mike?

Bluegreen · « **Reply #11 on:** September 27, 2012, 08:57:24 PM »

I'd like a couple

MRieck · « **Reply #12 on:** September 28, 2012, 04:51:38 AM »

Very, very soon guys

MRieck · « **Reply #13 on:** October 10, 2012, 03:10:02 PM »

I can get 60mm and 62mm. I am trying for the 61mm as well. If I get 5 or 6 guys buying I can give a discount off retail. They come in .030 and .040.

FunJimmy · « **Reply #14 on:** October 10, 2012, 03:24:01 PM »

Quote from: MRieck on October 10, 2012, 03:10:02 PM

I can get 60mm and 62mm. I am trying for the 61mm as well. If I get 5 or 6 guys buying I can give a discount off retail. They come in .030 and .040.

I'm looking for 61mm, but I'm sure 62 would work if needed.
61mm bore.

Thanks

fang · « **Reply #15 on:** October 10, 2012, 11:21:02 PM »

Got a Cycle-X email today talking about the MLS gaskets they are selling for the 550's, etc. It looks like they now have these available.

peace and grease,
-Fang

bwaller · « **Reply #16 on:** October 11, 2012, 04:50:33 AM »

Quote from: fang on October 10, 2012, 11:21:02 PM

Got a Cycle-X email today talking about the MLS gaskets they are selling for the 550's, etc. It looks like they now have these available.

peace and grease,
-Fang

Read through this tread. Mike isn't doing this for his health, he's trying to save the guys a buck.

RAFster122s · « **Reply #17 on:** October 11, 2012, 10:29:14 AM »

I am in FJ's camp, I have 61mm bore pistons. But, 62mm would probably work in a pinch.

Thanks for working to bring these to the light of day!

fang · « **Reply #18 on:** October 13, 2012, 09:09:52 PM »

Quote from: bwaller on October 11, 2012, 04:50:33 AM

Quote from: fang on October 10, 2012, 11:21:02 PM
Got a Cycle-X email today talking about the MLS gaskets they are selling for the 550's, etc. It looks like they now have these available.

peace and grease,
-Fang

Read through this tread. Mike isn't doing this for his health, he's trying to save the guys a buck.

Its my understanding that Mike is working with Cycle-X on this project

-Steve

bwaller · « **Reply #19 on:** October 19, 2012, 10:54:42 AM »

Mike I never got back about these but I'd take a 62mm bore gasket to start. My experience has been that most gaskets don't fit perfectly on the bores so bigger with a gasket is probably best.

I expect getting a 61mm gasket and enlarging the hole to fit isn't best with multi layers of viton coated steel.

MRieck · « **Reply #20 on:** October 19, 2012, 11:45:47 AM »

Quote from: bwaller on October 19, 2012, 10:54:42 AM

Mike I never got back about these but I'd take a 62mm bore gasket to start. My experience has been that most gaskets don't fit perfectly on the bores so bigger with a gasket is probably best.

I expect getting a 61mm gasket and enlarging the hole to fit isn't best with multi layers of viton coated steel.

Correct on all counts

FunJimmy · « **Reply #21 on:** October 19, 2012, 12:28:36 PM »

Quote from: bwaller on October 19, 2012, 10:54:42 AM

Mike I never got back about these but I'd take a 62mm bore gasket to start. My experience has been that most gaskets don't fit perfectly on the bores so bigger with a gasket is probably best.

I expect getting a 61mm gasket and enlarging the hole to fit isn't best with multi layers of viton coated steel.

Good point.

MRieck · « **Reply #22 on:** October 19, 2012, 01:52:18 PM »

Guys....please PM me and I'll get a count over the next 4 or 5 days and order them up.
Mike

mazen0822 · « **Reply #23 on:** October 27, 2012, 11:41:28 AM »

PM sent

I'm in on a 62mm

FunJimmy · « **Reply #24 on:** October 27, 2012, 11:56:52 AM »

Mike,

How do these MLS gaskets work with the notoriously leaky oil passages?
Do these still use an o-ring and if so, do they come with them?

News:

Author Topic: Any interest in MLS head gaskets for CB550's? (Read 7280 times)