Author Topic: CB750k7 Project: Operation Street Fighter (On the Road, Carb tuning in progress) (Read 24969 times)

Viktor.J · « **Reply #25 on:** February 21, 2013, 03:26:02 AM »

Quote from: laminaytrap on February 20, 2013, 11:52:50 PM

got bored

thanks to Oette for the idea!

wish my bike lived where I live

Nice rendering, didn't knew you used km/h in Canada !
Great design !
Have you Made up your mind on The rearsets ?

laminaytrap · « **Reply #26 on:** February 21, 2013, 04:06:59 AM »

Inspirtation came from here >

http://forums.sohc4.net/index.php?topic=86356.msg1328092#msg1328092

Parts will come from here >

http://www.tmart.com/LCD-Bike-Bicycle-Cycle-Computer-Odometer-Speedometer-Silver_p168053.html

An electronic tach I already have and this:

laminaytrap · « **Reply #27 on:** February 21, 2013, 04:16:31 AM »

@Viktor

Pretty sure it's smartest just to pickup some used rearsets (off a 600 most likely). It's not super high on my list right now unfortunately, winter is half over and i haven't even started doing work yet :s

In other news i did find one of these for cheap, and in "new" condition...

laminaytrap · « **Reply #28 on:** March 04, 2013, 04:24:09 AM »

So I had to dig out my trailer.

Then go do some work.

But I finally got it to my house

And dug out my front end parts, hopefully there'll be some time this week to start taking her apart and building new parts.

laminaytrap · « **Reply #29 on:** March 04, 2013, 12:28:33 PM »

So i had an hour this afternoon and started pulling stuff apart, had to deal with the gassy smell in my garage

Start

Finish

Need to go get my centre stand and jack stands so I can start pulling real stuff soon.

Any suggestions on exhaust bolts? Just soak and remove? Or are they going to give me trouble?

JC Blues · « **Reply #30 on:** March 04, 2013, 01:24:20 PM »

Mine gave me some trouble I broke the exhaust stud but mind you I forgot to soak them before hand. Just means I get new hd studs

laminaytrap · « **Reply #31 on:** March 05, 2013, 04:36:05 AM »

kk, I'll get the soak on them, I have the stock allen bolts, so i think i'll try to hit them with the impact driver (hammer style) and hope for the best.

I'm wondering if i should get some heat on them too. They probably haven't been off since the pipe was put on probably when it was new.

laminaytrap · « **Reply #32 on:** March 05, 2013, 07:44:24 AM »

So felt a bit ambitious, hope I don't regret it later!

So that's as far as i'll get today, need to p/u some PB or WD for the exhaust, then start looking at pulling the top end.

laminaytrap · « **Reply #33 on:** March 05, 2013, 11:39:41 AM »

so i did more

Pic of some casting numbers

and some numbers written on the head

Bagging and tagging to follow.

And I had a thought, maybe if i leave the exhaust on until i get the head unbolted i could use it to wiggle the head loose, should provide a good handle and may save some hammering.

I flipped it to make it readable, may have been written on the die itself?

JC Blues · « **Reply #34 on:** March 05, 2013, 01:44:59 PM »

Leaving the exhaust on sounds like a good idea for leverage, but im wondering if the collector would get hung up on the bottom of the engine ??and it would probably make the exhaust a real pain to get the off with the head moving around and such.

laminaytrap · « **Reply #35 on:** March 05, 2013, 01:51:30 PM »

Oh yeah sorry, wiggle the head loose, then bolt it back down like 3-4 nuts and remove the exhaust.

As far as I've read it's just the initial breaking free that's the issue, not the actual removal of it.

laminaytrap · « **Reply #36 on:** March 07, 2013, 12:30:39 PM »

So head and jugs are loose, but not apart nor are they off yet.

Thought i'd look for something I lost a little while back, and this is why those restrictive ports are not necessarily a bad thing.

There it is!

Luckily it was jammed in the intake, not further. That's all i know that fell in there, going to soak those exhaust bolts more and filter the oil to see if there's anything interesting in it. Hopefully pics of the head off tonight.

EDIT: and buy a 3/8 drive 6mm allen tool for the silly exhaust bolts.

laminaytrap · « **Reply #37 on:** March 07, 2013, 06:11:06 PM »

Maybe I'm just lucky, but my head loosened up easy too, if only the exhaust were so happy...

laminaytrap · « **Reply #38 on:** March 07, 2013, 08:19:43 PM »

Oh and i picked up another Showa, this one has a remote reservoir on a flex line. $20

I'll have to see if it's worth swapping stuff around between the two, or just run it as is, the spring could use some powder.

laminaytrap · « **Reply #39 on:** March 08, 2013, 11:18:11 AM »

Those bolts don't stand a chance

laminaytrap · « **Reply #40 on:** March 08, 2013, 04:27:24 PM »

Ok They actually look pretty good, a little scratching, a little staining, but nothing serious,

Pistons look pretty clean, don't know how.

But the gasket is all oblong, which is weird...

Opinions?