« previous next »
Pages: [1] 2 3 ... 7   Go Down

Author Topic: After cam swap, won't start | Block off pics  (Read 21844 times)

0 Members and 1 Guest are viewing this topic.

Offline stereosilence

  • Hot Shot
  • ***
  • Posts: 544
  • 1975 CB550K
After cam swap, won't start | Block off pics
« on: October 02, 2012, 03:58:27 PM »
Finally got the 650 cam swapped in and the valves adjusted and everything put back together. Now it won't start. When I hold the electric starter the best it will do is cough some and a bit of white smoke will come out (which, if I remember correctly, denotes oil). I tried with the choke on and off.

I got it started yesterday for just a bit, but it was difficult then too. I also tried kick starting it, but no luck. Any words of wisdom?
« Last Edit: October 16, 2012, 01:15:21 PM by stereosilence »
Logged

Offline Dimitri13

  • Not a
  • Master
  • *****
  • Posts: 1,603
  • 1974 CB550K
Re: After cam swap, won't start
« Reply #1 on: October 02, 2012, 04:11:56 PM »
Any jetting changes?
Logged

Offline stereosilence

  • Hot Shot
  • ***
  • Posts: 544
  • 1975 CB550K
Re: After cam swap, won't start
« Reply #2 on: October 02, 2012, 04:18:44 PM »
Nope.
Logged

Offline matt mattison

  • Enthusiast
  • **
  • Posts: 239
Re: After cam swap, won't start
« Reply #3 on: October 02, 2012, 04:37:56 PM »
Did you static time the engine before trying to fire it up?
Logged
1975 CB550F
2011 MV Agusta Brutale 1090RR

Offline Gordon

  • Global Moderator
  • Really Old Timer ...
  • *****
  • Posts: 12,114
  • 750K1, 550K2
Re: After cam swap, won't start
« Reply #4 on: October 02, 2012, 04:56:29 PM »
Did you reconnect the plug wires correctly?
Logged

Offline stereosilence

  • Hot Shot
  • ***
  • Posts: 544
  • 1975 CB550K
Re: After cam swap, won't start
« Reply #5 on: October 02, 2012, 04:58:28 PM »
I'm not sure what static timing is. I aligned the new camshaft correctly with the TF-14 mark.

As I understand it, plugs 1/4 are interchangeable and 2/3 are interchangeable, correct? There is no way that I could have plug 4 installed to plug 1 and it wouldn't work is there?
Logged

Offline steam-powered man

  • Not the eggman, Not the walrus, I am the
  • Hot Shot
  • ***
  • Posts: 591
  • Where are you going? I was going to make Espresso
Re: After cam swap, won't start
« Reply #6 on: October 02, 2012, 05:03:12 PM »
cam might be 180 out, try swapping the blue/yellow points wires.  btdt
Logged
searching for a dr350se

Offline dave500

  • Really Old Timer ...
  • *******
  • Posts: 17,014
  • WHAT?no gravy?
Re: After cam swap, won't start
« Reply #7 on: October 02, 2012, 06:12:09 PM »
the cam CANNOT be 180 out.
Logged

Offline stereosilence

  • Hot Shot
  • ***
  • Posts: 544
  • 1975 CB550K
Re: After cam swap, won't start
« Reply #8 on: October 02, 2012, 06:21:08 PM »
Checking the timing is probably a good place to start. I'll get on that and get back to ya'll. Any other suggestions are welcome. I actually ran it for a few seconds yesterday, so I don't know what happened. I cut it off and installed the 650 tachometer and drive and today it won't start.
Logged

Offline MCRider

  • Such is the life of a
  • Really Old Timer ...
  • *******
  • Posts: 14,376
  • Today's Lesson: One good turn deserves another.
Re: After cam swap, won't start
« Reply #9 on: October 02, 2012, 06:35:25 PM »
Quote from: steam-powered man on October 02, 2012, 05:03:12 PM
cam might be 180 out, try swapping the blue/yellow points wires.  btdt
In deference to the "can't be 180 out" idea, I can't think it thru. I do know that there have been 3 instances of people swapping cams, suffering a no start condition, swap the point wires, and it starts. IF that's not 180deg out, I don't know.

Weren't you one of those victims SPM?

Proof is in the punch, swap the wires, can't hurt.
Logged
Ride Safe:
Ron
1988 NT650 HawkGT;  1978 CB400 Hawk;  1975 CB750F -Free Bird; 1968 CB77 Super Hawk -Ticker;  Phaedrus 1972 CB750K2- Build Thread
"Sometimes the light's all shining on me, other times I can barely see, lately it appears to me, what a long, strange trip its been."

Offline dave500

  • Really Old Timer ...
  • *******
  • Posts: 17,014
  • WHAT?no gravy?
Re: After cam swap, won't start
« Reply #10 on: October 02, 2012, 08:26:19 PM »
it was running with the cam swapped and now its not,unless the wire swapping elves are at it again?
Logged

Offline steam-powered man

  • Not the eggman, Not the walrus, I am the
  • Hot Shot
  • ***
  • Posts: 591
  • Where are you going? I was going to make Espresso
Re: After cam swap, won't start
« Reply #11 on: October 02, 2012, 08:48:51 PM »
yup, that was me.  set the cam with slot pointing down instead of up.  cough, boom, sputter, fart, and repeat.  swapped points wires and zoom!   wasn't that 180 out?  sometimes i think i live in an alternate universe where up is actually 270 degrees from down.   :o   
Logged
searching for a dr350se

Offline dave500

  • Really Old Timer ...
  • *******
  • Posts: 17,014
  • WHAT?no gravy?
Re: After cam swap, won't start
« Reply #12 on: October 02, 2012, 09:14:29 PM »
the slot should be horizontal,you must have had the crank misaligned aswell?if you have the cam a few teeth out you will bend valves.
Logged

Offline 750resurrection

  • Hot Shot
  • ***
  • Posts: 288
Re: After cam swap, won't start
« Reply #13 on: October 02, 2012, 09:18:57 PM »
Use some starting fluid, especially if you have pods.
Logged

Offline phil71

  • Master
  • *****
  • Posts: 1,813
Re: After cam swap, won't start
« Reply #14 on: October 02, 2012, 09:33:17 PM »
Starting fluid !? 
Logged

Offline dave500

  • Really Old Timer ...
  • *******
  • Posts: 17,014
  • WHAT?no gravy?
Re: After cam swap, won't start
« Reply #15 on: October 02, 2012, 09:38:06 PM »
yeah starting fluid is beer,then you run on bourbon!
Logged

Offline steam-powered man

  • Not the eggman, Not the walrus, I am the
  • Hot Shot
  • ***
  • Posts: 591
  • Where are you going? I was going to make Espresso
Re: After cam swap, won't start
« Reply #16 on: October 03, 2012, 05:15:59 AM »
actually, on this particular cb750k there were 2 "index lines" aligned horizontally with the cam holder and one "slot" to be pointing up.  got some good advice and saved me from yanking the engine.   ;)
Logged
searching for a dr350se

Offline stereosilence

  • Hot Shot
  • ***
  • Posts: 544
  • 1975 CB550K
Re: After cam swap, won't start
« Reply #17 on: October 03, 2012, 07:41:28 AM »
Well, I aligned the notch horizontally according to the manual. I know this cause I did it wrong the first time and to go back and redo it.  ::)

I won't have a chance to work on it til tomorrow. I'll try swapping the wires and checking the timing.
Logged

Offline dave500

  • Really Old Timer ...
  • *******
  • Posts: 17,014
  • WHAT?no gravy?
Re: After cam swap, won't start
« Reply #18 on: October 03, 2012, 12:28:20 PM »
its a 550 not a 750 steam man.
Logged

Offline steam-powered man

  • Not the eggman, Not the walrus, I am the
  • Hot Shot
  • ***
  • Posts: 591
  • Where are you going? I was going to make Espresso
Re: After cam swap, won't start
« Reply #19 on: October 03, 2012, 05:40:29 PM »
"its a 550 not a 750"

oops / eek! 
Logged
searching for a dr350se

Offline stereosilence

  • Hot Shot
  • ***
  • Posts: 544
  • 1975 CB550K
Re: After cam swap, won't start
« Reply #20 on: October 04, 2012, 05:20:32 PM »
Got home and was going to check the timing, tried to turn it over and it made a terrible noise. On the other hand, the ignition timing was at least close, so I don't need to swap wires or anything. I posted a video of the sound. If you have any ideas, let me know. I can't tell if it is metal on metal scraping or a rubber-squealing noise. I guess I'll take it apart *again* a piece at a time and see if I can find the problem.

Engine Noise
Logged

Offline MCRider

  • Such is the life of a
  • Really Old Timer ...
  • *******
  • Posts: 14,376
  • Today's Lesson: One good turn deserves another.
Re: After cam swap, won't start | Engine Noise Vid!
« Reply #21 on: October 04, 2012, 05:33:34 PM »
Quote from: LesterPiglet on October 04, 2012, 05:27:06 PM
Please don't use that nut for turning the engine, they snap regularly.
Curious. That's what its for. Nice if one can remove the spark plugs, but even so... that's what that nut is for. Treat it right, it won't snap.

What do you use?
Logged
Ride Safe:
Ron
1988 NT650 HawkGT;  1978 CB400 Hawk;  1975 CB750F -Free Bird; 1968 CB77 Super Hawk -Ticker;  Phaedrus 1972 CB750K2- Build Thread
"Sometimes the light's all shining on me, other times I can barely see, lately it appears to me, what a long, strange trip its been."

Offline crazypj

  • I'm brill, me
  • Old Timer
  • ******
  • Posts: 4,467
  • first 100,000 miles. 1977 CB550F
Re: After cam swap, won't start | Engine Noise Vid!
« Reply #22 on: October 04, 2012, 05:35:06 PM »
Quote from: MCRider on October 02, 2012, 06:35:25 PM
Quote from: steam-powered man on October 02, 2012, 05:03:12 PM
cam might be 180 out, try swapping the blue/yellow points wires.  btdt
In deference to the "can't be 180 out" idea, I can't think it thru. I do know that there have been 3 instances of people swapping cams, suffering a no start condition, swap the point wires, and it starts. IF that's not 180deg out, I don't know.

Weren't you one of those victims SPM?

Proof is in the punch, swap the wires, can't hurt.

 That can only work if points cam is mounted on camshaft.
This isn't so can't be 180 out
Logged
I fake being smart pretty good
'you can take my word for it or argue until you find out I'm right'

Offline Tews19

  • I am no
  • Really Old Timer ...
  • *******
  • Posts: 6,465
Re: After cam swap, won't start | Engine Noise Vid!
« Reply #23 on: October 04, 2012, 05:53:17 PM »
Quote from: MCRider on October 04, 2012, 05:33:34 PM
Quote from: LesterPiglet on October 04, 2012, 05:27:06 PM
Please don't use that nut for turning the engine, they snap regularly.
Curious. That's what its for. Nice if one can remove the spark plugs, but even so... that's what that nut is for. Treat it right, it won't snap.

What do you use?


Curious, i thought that is what it was for too... Thats what I've used...

Did you stick a cat in the cylinder????????????? Sounds like one is getting kicked
Logged
1969 Honda CB750... Basket case
1970 Honda CB750 survivor.

Offline MCRider

  • Such is the life of a
  • Really Old Timer ...
  • *******
  • Posts: 14,376
  • Today's Lesson: One good turn deserves another.
Re: After cam swap, won't start | Engine Noise Vid!
« Reply #24 on: October 04, 2012, 05:59:38 PM »
Sorry that doesn't sound good. Maybe you've answered this, but are they new pistons and rings? Were the rings end gaps checked.

Be sure to document your cam timing for posterity. Curious.
Logged
Ride Safe:
Ron
1988 NT650 HawkGT;  1978 CB400 Hawk;  1975 CB750F -Free Bird; 1968 CB77 Super Hawk -Ticker;  Phaedrus 1972 CB750K2- Build Thread
"Sometimes the light's all shining on me, other times I can barely see, lately it appears to me, what a long, strange trip its been."
Pages: [1] 2 3 ... 7   Go Up
« previous next »