Author Topic: Cut n Weld day ....  (Read 10480 times)

0 Members and 5 Guests are viewing this topic.

Offline WarwickE36

  • Expert
  • ****
  • Posts: 761
Cut n Weld day ....
« on: October 10, 2012, 03:27:38 PM »
Did a little fabrication on my cafe CB ...





the rear set section is high for 2 reasons, the first being the bike will have an undertail exhaust.  Number 2 it is going to have just a seat cushion not a bubble.  This bike is the anti bubble cafe racer!  Also bear in mind the tire will sit higher with shocks installed to proper height, right now the swing arm is sitting low.... Let me know what you think.  Hate on haters  ;D
" Why does anyone get offended by what someone does to their own bike? I dont get it. "

You made me think about it after I cheered knowing someone else would like to know what these control freaks are up to.
 Every time any owner strips whatever precious Honda part the horrified purists parts go up in value. That's not the part that bothers them.
 What bothers them is they sat up late at night, their breast full of wonder and estrogen, unable to sleep, dreaming about their lovely darling and all her glory... and next thing you know someone else doesn't share their emotional deluge and their reaction is they must spread their mind museum as far as they possibly can, taking over as much of the real world as possible.

Drink fast, drive slow, but ride it like you stole it

1974 Cb550 with style
2004 SV650s

Offline lucky

  • Really Old Timer ...
  • *******
  • Posts: 6,717
Re: Cut n Weld day ....
« Reply #1 on: October 10, 2012, 03:30:50 PM »
WHY do you want an undertail exhaust???

Think.

It will cause all kinds of problems with the SOHC engine.

Offline WarwickE36

  • Expert
  • ****
  • Posts: 761
Re: Cut n Weld day ....
« Reply #2 on: October 10, 2012, 03:33:22 PM »
And we have our first hater, I want it because all the old timers will hate it. 
" Why does anyone get offended by what someone does to their own bike? I dont get it. "

You made me think about it after I cheered knowing someone else would like to know what these control freaks are up to.
 Every time any owner strips whatever precious Honda part the horrified purists parts go up in value. That's not the part that bothers them.
 What bothers them is they sat up late at night, their breast full of wonder and estrogen, unable to sleep, dreaming about their lovely darling and all her glory... and next thing you know someone else doesn't share their emotional deluge and their reaction is they must spread their mind museum as far as they possibly can, taking over as much of the real world as possible.

Drink fast, drive slow, but ride it like you stole it

1974 Cb550 with style
2004 SV650s

Offline Mcwilliams570

  • Hot Shot
  • ***
  • Posts: 646
Re: Cut n Weld day ....
« Reply #3 on: October 10, 2012, 03:38:16 PM »
Heya Warwick good to see you back. Its hard for me to tell what it is going to look like. Will there be 4 pipes coming out back or just 2. Also how will you route them to come up from the engine to the tail section. Should be a fun project keep us updated..

Matt
My CB550 project http://forums.sohc4.net/index.php?topic=101182.0

Project UFB Cb550 http://forums.sohc4.net/index.php?topic=112143.0

Like a 10 dollar hooker on Friday night its going to be ridden.

1974 cb550
1975 cb550
2005 vmax
2009 vmax-sold
1981 gl500i

Offline WarwickE36

  • Expert
  • ****
  • Posts: 761
Re: Cut n Weld day ....
« Reply #4 on: October 10, 2012, 03:40:59 PM »
Its a cb350 twin shhhhhhhhhh dont tell anyone, it will be 2 into 1 with one pipe routed up the left side frame then tucked underneath the upper seat.  Ill keep posting pics
" Why does anyone get offended by what someone does to their own bike? I dont get it. "

You made me think about it after I cheered knowing someone else would like to know what these control freaks are up to.
 Every time any owner strips whatever precious Honda part the horrified purists parts go up in value. That's not the part that bothers them.
 What bothers them is they sat up late at night, their breast full of wonder and estrogen, unable to sleep, dreaming about their lovely darling and all her glory... and next thing you know someone else doesn't share their emotional deluge and their reaction is they must spread their mind museum as far as they possibly can, taking over as much of the real world as possible.

Drink fast, drive slow, but ride it like you stole it

1974 Cb550 with style
2004 SV650s

Offline WarwickE36

  • Expert
  • ****
  • Posts: 761
Re: Cut n Weld day ....
« Reply #5 on: October 10, 2012, 03:43:03 PM »
Inspiration for the exhaust came from this bike. 

" Why does anyone get offended by what someone does to their own bike? I dont get it. "

You made me think about it after I cheered knowing someone else would like to know what these control freaks are up to.
 Every time any owner strips whatever precious Honda part the horrified purists parts go up in value. That's not the part that bothers them.
 What bothers them is they sat up late at night, their breast full of wonder and estrogen, unable to sleep, dreaming about their lovely darling and all her glory... and next thing you know someone else doesn't share their emotional deluge and their reaction is they must spread their mind museum as far as they possibly can, taking over as much of the real world as possible.

Drink fast, drive slow, but ride it like you stole it

1974 Cb550 with style
2004 SV650s

Offline DustyRags

  • I'm not skilled, I'm just a
  • Hot Shot
  • ***
  • Posts: 720
  • Just try it and see what happens
Re: Cut n Weld day ....
« Reply #6 on: October 10, 2012, 05:11:35 PM »
Man, undertail exhaust, twin cylinder... you're gonna get slagged!  ::)

Be curious to see how this turns out, I love the idea of the higher p-pad to act as the bumstop- should still give you that cafe look and feel, but with a second seat. Good times.
1976 CB550K- sold
2005 Kawasaki Vulcan 500- sold
2000 CB750 Nighthawk - sold
1975 XL350 - crashed
2004 Suzuki Vstrom 650 - sold

Offline Killer Canary

  • Master
  • *****
  • Posts: 1,805
  • Typical Bran Muffin
Re: Cut n Weld day ....
« Reply #7 on: October 10, 2012, 05:47:46 PM »
That's ambitious. Do you have the goodies to bend headers? The example looks gooood! :)
If it's worth doing at all it's worth over-doing.
Honda MT250, CB400F, CB450K, CB550, GL500, CBR929
Kawi GPz900, H1

Offline WarwickE36

  • Expert
  • ****
  • Posts: 761
Re: Cut n Weld day ....
« Reply #8 on: October 10, 2012, 06:07:13 PM »
My buddy owns a custom bike shop.  He will be doing the exhaust for me.  It's good knowing the right people. 
" Why does anyone get offended by what someone does to their own bike? I dont get it. "

You made me think about it after I cheered knowing someone else would like to know what these control freaks are up to.
 Every time any owner strips whatever precious Honda part the horrified purists parts go up in value. That's not the part that bothers them.
 What bothers them is they sat up late at night, their breast full of wonder and estrogen, unable to sleep, dreaming about their lovely darling and all her glory... and next thing you know someone else doesn't share their emotional deluge and their reaction is they must spread their mind museum as far as they possibly can, taking over as much of the real world as possible.

Drink fast, drive slow, but ride it like you stole it

1974 Cb550 with style
2004 SV650s

Offline mono

  • Definitely no
  • Expert
  • ****
  • Posts: 1,271
  • 1975 Honda CB550, 1978 CB750K (in progress)
Re: Cut n Weld day ....
« Reply #9 on: October 11, 2012, 06:32:27 AM »
WHY do you want an undertail exhaust???

Think.

It will cause all kinds of problems with the SOHC engine.

Lucky, what kind of problems would an undertail exhaust cause an SOHC engine - and why?  i'm not sure i see why routing the exhaust differently would cause problems.  please explain?

Offline mono

  • Definitely no
  • Expert
  • ****
  • Posts: 1,271
  • 1975 Honda CB550, 1978 CB750K (in progress)
Re: Cut n Weld day ....
« Reply #10 on: October 11, 2012, 06:33:37 AM »
also, Warwick - i like the frame design.   can't wait to see the custom pipes!

Offline WarwickE36

  • Expert
  • ****
  • Posts: 761
Re: Cut n Weld day ....
« Reply #11 on: October 11, 2012, 07:23:30 AM »
This is what it looks like from the front... gives a better idea for the feel...



@mono, there are people on this forum that believe these bikes will never run reasonably well without being completely bone stock.   I laugh at those people.  Is it easier to make it run right, sure, but where's the fun in that

Before I get flamed, there are gussets on the way, this is a work in progress
" Why does anyone get offended by what someone does to their own bike? I dont get it. "

You made me think about it after I cheered knowing someone else would like to know what these control freaks are up to.
 Every time any owner strips whatever precious Honda part the horrified purists parts go up in value. That's not the part that bothers them.
 What bothers them is they sat up late at night, their breast full of wonder and estrogen, unable to sleep, dreaming about their lovely darling and all her glory... and next thing you know someone else doesn't share their emotional deluge and their reaction is they must spread their mind museum as far as they possibly can, taking over as much of the real world as possible.

Drink fast, drive slow, but ride it like you stole it

1974 Cb550 with style
2004 SV650s

Offline MCRider

  • Such is the life of a
  • Really Old Timer ...
  • *******
  • Posts: 14,376
  • Today's Lesson: One good turn deserves another.
Re: Cut n Weld day ....
« Reply #12 on: October 11, 2012, 07:40:10 AM »
WHY do you want an undertail exhaust???

Think.

It will cause all kinds of problems with the SOHC engine.

Lucky, what kind of problems would an undertail exhaust cause an SOHC engine - and why?  i'm not sure i see why routing the exhaust differently would cause problems.  please explain?
Really! Blunt ended statements of pseudo fact do nothing to further the discussion. Give a reason or withhold the comment.

Or so I think.

Personally, I see no reason why it would cause a problem any more than any other homemade exhaust might. Flip a coin, could actually be an improvement. Certainly solves a ground clearance problem.
Ride Safe:
Ron
1988 NT650 HawkGT;  1978 CB400 Hawk;  1975 CB750F -Free Bird; 1968 CB77 Super Hawk -Ticker;  Phaedrus 1972 CB750K2- Build Thread
"Sometimes the light's all shining on me, other times I can barely see, lately it appears to me, what a long, strange trip its been."

Offline Killer Canary

  • Master
  • *****
  • Posts: 1,805
  • Typical Bran Muffin
Re: Cut n Weld day ....
« Reply #13 on: October 11, 2012, 07:42:31 AM »
I would think the important thing would be to keep header lengths equal.
If it's worth doing at all it's worth over-doing.
Honda MT250, CB400F, CB450K, CB550, GL500, CBR929
Kawi GPz900, H1

Offline Killer Canary

  • Master
  • *****
  • Posts: 1,805
  • Typical Bran Muffin
Re: Cut n Weld day ....
« Reply #14 on: October 11, 2012, 07:47:10 AM »
Quote
Really! Blunt ended statements of pseudo fact do nothing to further the discussion. Give a reason or withhold the comment.
Start every post with, and I quote "Please don't respond if you only think you know" ;D
If it's worth doing at all it's worth over-doing.
Honda MT250, CB400F, CB450K, CB550, GL500, CBR929
Kawi GPz900, H1

Offline flybox1

  • My wife thinks I'm a
  • Really Old Timer ...
  • *******
  • Posts: 14,301
Re: Cut n Weld day ....
« Reply #15 on: October 11, 2012, 08:07:27 AM »
My buddy owns a custom bike shop.  He will be doing the exhaust for me.  It's good knowing the right people.
love the idea.
Keep us posted!
'78 750K (F3 engine) PD42b's, Modified airbox w/K&N  filter, 40/110 jets, 1 needle shim, IMS@ 1 turn out. Kerker + Cone 18" QuietCore

Past Bikes
1974 550K0 (stock), 1973 CB350F (stock), 1983 Yamaha XS400K (POS)
77/78 cool 2 member #3
"Knowledge without mileage equals bullsh!t" - Henry Rollins

"This is my CB. There are many like it, but this one is mine…"

Offline lucky

  • Really Old Timer ...
  • *******
  • Posts: 6,717
Re: Cut n Weld day ....
« Reply #16 on: October 11, 2012, 08:25:36 AM »
And we have our first hater, I want it because all the old timers will hate it.

Hater???/  It does NOT have to have stock exhaust but just not up high for this particular engine. Most of the bikes that have high exhausts in the rear was for a very good reason. They had V4 engines OR V twin engines and the rear cylinder exited the rear because IT MADE SENSE.

Not really . I just am trying to save you a lot of hell.
Carry on floppy ears!!  LOL.lol

BTW.... some old timers have some information that is very helpful.
If you listen to some old timers you may save time ,money, pain and frustration.
Also OUR generation got you all the modern luxuries you now enjoy. We got us to the moon. WE made the airplanes, We made the trains, We built the freeway system. We made the first phones that worked perfect and clear as a Bell.





« Last Edit: October 11, 2012, 08:38:04 AM by lucky »

Offline 750resurrection

  • Hot Shot
  • ***
  • Posts: 288
Re: Cut n Weld day ....
« Reply #17 on: October 11, 2012, 08:28:38 AM »
I would think the important thing would be to keep header lengths equal.

When Warwick pops the wheelie then does his giant sheep defying air time jump and the rear tire and rim closes the exhaust on the 5G landing impact, Lucky will be saying I told you so.  ;D

Offline lucky

  • Really Old Timer ...
  • *******
  • Posts: 6,717
Re: Cut n Weld day ....
« Reply #18 on: October 11, 2012, 08:30:36 AM »
Inspiration for the exhaust came from this bike. 



That example bike already looks like the riders leg and a$$ got hot, and the shift lever linkage is all bent up.
Just think if that pipe exited down low then no hot a$$ and no hot leg, and the shift linkage would get straitened out.  See what I mean.

Think... why do you want the exhaust out the a$$ up high. Why??
« Last Edit: October 11, 2012, 08:39:12 AM by lucky »

Offline flybox1

  • My wife thinks I'm a
  • Really Old Timer ...
  • *******
  • Posts: 14,301
Re: Cut n Weld day ....
« Reply #19 on: October 11, 2012, 08:45:15 AM »
because it looks cool, and its his bike and he can do as he pleases...
heat shields will save his a$$ and his legs.
changing the exhaust route will not change the function of the bike.


'78 750K (F3 engine) PD42b's, Modified airbox w/K&N  filter, 40/110 jets, 1 needle shim, IMS@ 1 turn out. Kerker + Cone 18" QuietCore

Past Bikes
1974 550K0 (stock), 1973 CB350F (stock), 1983 Yamaha XS400K (POS)
77/78 cool 2 member #3
"Knowledge without mileage equals bullsh!t" - Henry Rollins

"This is my CB. There are many like it, but this one is mine…"

Offline MCRider

  • Such is the life of a
  • Really Old Timer ...
  • *******
  • Posts: 14,376
  • Today's Lesson: One good turn deserves another.
Re: Cut n Weld day ....
« Reply #20 on: October 11, 2012, 08:49:32 AM »
That's better. So its not a performance issue, at least so far.

I'd agree there are often design compromises, heat and controls, with the high under seat pipes. But for many bikes, Ducatis, Hondas, etc. production under seat pipes are no problem with heat or controls. usually V-twins or 4s though. So I'd like to see what they come up with.

For a track bike, its a great thing.
Ride Safe:
Ron
1988 NT650 HawkGT;  1978 CB400 Hawk;  1975 CB750F -Free Bird; 1968 CB77 Super Hawk -Ticker;  Phaedrus 1972 CB750K2- Build Thread
"Sometimes the light's all shining on me, other times I can barely see, lately it appears to me, what a long, strange trip its been."

Offline Killer Canary

  • Master
  • *****
  • Posts: 1,805
  • Typical Bran Muffin
Re: Cut n Weld day ....
« Reply #21 on: October 11, 2012, 08:50:10 AM »
All of the big 4's late model transverse 4 crotch rockets have underseat. Whether it's your thing or not, it works, and well. SOHCs do have the compression to hurl those heavy exhaust gasses uphill also, even defying gravity.
If it's worth doing at all it's worth over-doing.
Honda MT250, CB400F, CB450K, CB550, GL500, CBR929
Kawi GPz900, H1

Offline stereosilence

  • Hot Shot
  • ***
  • Posts: 544
  • 1975 CB550K
Re: Cut n Weld day ....
« Reply #22 on: October 11, 2012, 09:14:48 AM »
Wait. When did we start caring about how mods affect comfort or performance on this forum?  :o

Cafe/customized bikes are some of the most uncomfortable things known to man. They make the seat a vinyl covered piece of metal and put it as far back as possible. Then, you remove all baffles and possibly eff the pipes all up and make it loud as hell and destroy the calculated backpressure (because nothing is quite as cool as hearing damage). Next, you put some big-ass ugly tires that will probably put you on your side the first chance you get. Of course, you also have to cut the back fender off (and maybe the frame) to get covered in mud and road-oil if it ever decides to sprinkle. Finally, you replace the handle bars with something that will allow you to put your hands as close to the front axle as you possibly can. Don't forget the pods either (but that is another thread).

So, you end up with a bike that wasn't fast (nor was supposed to be, its 40 years old...), now runs rough as a dirt road, sounds like a war zone, is as comfortable as riding on a rail, and possibly lacks basic road-worthiness equipment.

But it looks awesome. It's a piece of art straight out of your imagination. People give you respect cause they can't dream of have the technical knowledge or creativity to make it happen. Nobody calls you a moto-douche or lumps you in with the obnoxious squids on the highway. Nobody thinks you are an 55 year old account in midlife crisis (Harley's anyone?). Everyone turns their head, the chicks dig it, and you look like a total badass when you roll up.

If you want performance, go buy a BMW R1000s or something. For comfort, get a Goldwing. For bling, a Harley. But for style points, make a custom bike.

Carry on with the undertail exhaust. Even if it makes your seat hot, people pay a lot of money for an evenly tanned butt.  ;D

Offline iron_worker

  • Master
  • *****
  • Posts: 2,081
Re: Cut n Weld day ....
« Reply #23 on: October 11, 2012, 09:19:51 AM »
My 2003 CBR 600RR had an undertail exhaust. They are of course DOHC I4s ... but I will have you know it worked very well and I was never burned by it.

110hp in a 400lb ... man was it fun!

IW

Offline mono

  • Definitely no
  • Expert
  • ****
  • Posts: 1,271
  • 1975 Honda CB550, 1978 CB750K (in progress)
Re: Cut n Weld day ....
« Reply #24 on: October 11, 2012, 09:35:38 AM »
+1 to Stereo's sermon.

+1 to Lucky's "whipper-snapper" points, also.