« previous next »
Pages: [1] 2  All   Go Down

Author Topic: sohc f2 head  (Read 6401 times)

0 Members and 1 Guest are viewing this topic.

Offline tony sawyer

  • Full Member
  • *
  • Posts: 34
sohc f2 head
« on: December 11, 2012, 11:51:26 AM »
hi any problems with the f2 head on f1 or k barrels ,i take it i have to use f2 pistons or higher comp than stock  any other issuse rgds tony
Logged

Offline madmtnmotors

  • When did I get to be a
  • Really Old Timer ...
  • *******
  • Posts: 6,090
  • Sunny Central Florida
Re: sohc f2 head
« Reply #1 on: December 11, 2012, 12:23:46 PM »
Here's one post: http://forums.sohc4.net/index.php?topic=369.msg42059#msg42059

and there are numerous threads devoted to this, still filtering through the search results.

http://forums.sohc4.net/index.php?topic=17622.0;nowap
http://forums.sohc4.net/index.php?topic=49659.msg547619#msg547619



 The later F2 heads require the ability to address the exposed studs that happen to serve as oil returns on the earlier heads and cylinders. You either need to combine the F2 head with F2 cylinders (and the FOUR additional o-rings at the base of the cylinders) or the F2 head can be sleeved (AND sealed) at these stud locations to eliminate their exposure to the atmosphere in order to use the F2 head with earlier cylinders. I just spent two months chasing the source of the four hot oil fountains at the head because the P.O. left out the four o-rings at the base of the cylinders on my recently aquired F2/F3 (78 CB750F)
Logged
TAMTF...


Wilbur



Projects:
"Evolution": http://forums.sohc4.net/index.php?topic=100352.0
"P.O. Debacle": http://forums.sohc4.net/index.php/topic,126692.msg1441661.html#msg1441661
F2/F3 O-rings: http://forums.sohc4.net/index.php?topic=113672.msg1300721#msg1300721
Cam Tower Studs: https://www.mcmaster.com/#93210a017/=t19sgp
Clean up that nasty harness: http://forums.sohc4.net/index.php?topic=137351.msg1549191#msg1549191
http://forums.sohc4.net/index.php/topic,148188.msg1688494.html#msg1688494
http://forums.sohc4.net/index.php/topic,139544.msg1579364.html#msg1579364
                                          
Charging system diagnosis: http://forums.sohc4.net/index.php?topic=1012.msg8345#msg8345
Get the manuals: http://manuals.sohc4.net/cb750k/
The Dragon: http://forums.sohc4.net/index.php?topic=45183.msg1571675#msg1571675
Headlight Switch: http://forums.sohc4.net/index.php?topic=113986.msg1283236#msg1283236
Branden's leak free top end thread: http://forums.sohc4.net/index.php?topic=107040.0
Engine Lifting Made Easy: http://forums.sohc4.net/index.php/topic,58210.msg1684742.html#msg1684742
                                      http://forums.sohc4.net/index.php/topic,100352.msg1675840.html#msg1675840
Static and Dynamic Timing: http://www.hondachopper.com/garage/carb_info/timing/timing1.html
Airbox Gasket Replacement: http://forums.sohc4.net/index.php/topic,114485.msg1290000.html#msg1290000
"Café" : http://forums.sohc4.net/index.php/topic,84697.msg953814.html#msg953814
PD Carb Choke Linkage: http://forums.sohc4.net/index.php/topic,100352.msg1669248.html#msg1669248
                                    http://forums.sohc4.net/index.php/topic,110931.msg1248354.html#msg1248354
                                    http://forums.sohc4.net/index.php/topic,48858.msg515204.html#msg515204
Follow up on your damn posts: http://forums.sohc4.net/index.php/topic,144305.msg1791605.html#msg1791605
Taiwanese Cam Chain Tensioners:  http://forums.sohc4.net/index.php/topic,155043.msg1774841.html#msg1774841
Gumtwo Seat Cover: http://forums.sohc4.net/index.php/topic,164440.msg1897366.html#msg1897366
Primary Drive: http://forums.sohc4.net/index.php/topic,166063.msg1919278.html#msg1919278
Tank Latch: http://forums.sohc4.net/index.php/topic,165975.msg1919495.html#msg1919495
Shorten your forks: http://vintage-and-classic-honda-s.456789.n3.nabble.com/How-to-shorten-forks-td4042465.html DO NOT CUT THE SPRINGS!
Clutch How To: http://vintage-and-classic-honda-s.456789.n3.nabble.com/How-to-change-and-adjust-a-clutch-SOHC-td4040391.html
Late model K7/K8/F2/F3 front sprocket cover removal: http://forums.sohc4.net/index.php/topic,178428.msg2072279.html#msg2072279
630 to 530 conversion: http://forums.sohc4.net/index.php/topic,180710.msg2094423.html#msg2094423

Sent from my Tandy TRS-80!

Offline Jerry Rxman Griffin aka MuthaF'er

  • This MuthaF'er is getting to be a
  • Really Old Timer ...
  • *******
  • Posts: 14,902
  • Bought her new 4/75
Re: sohc f2 head
« Reply #2 on: December 11, 2012, 12:26:35 PM »
Yeah, it's pretty much as cases-up swap BUT if can be done otherwise BUT it ain't worth the trouble to do otherwise
Logged
As of today 3/13/2012 my original owner 75 CB750F has made it through 3 wives, er EX-wives. Free at last.  ;-)

Offline tony sawyer

  • Full Member
  • *
  • Posts: 34
Re: sohc f2 head
« Reply #3 on: December 11, 2012, 12:55:11 PM »
hi have  another  option of f2 head and barrels 836 or f1 head and barrels 836 both pistons 10.25
wot cam any prefrences
Logged

Offline Sam Green Racing

  • Moderator
  • Really Old Timer ...
  • *****
  • Posts: 16,068
  • I REALLY? hate black rims.
Re: sohc f2 head
« Reply #4 on: December 11, 2012, 01:17:36 PM »
I take it it's for the side car :-\ if so, depends on where you're racing.
Megacycle 125-70/75 for IOM, gives more top end.
Megacycle 125-60/65 or Dynoman DP295 for short circuits, lots of low down and mid range grunt with 836 pistons.

Sam. :)
Logged
C95 sprint bike.
CB95 hybrid race bike
CB95 race bike
CB92
RS 175. sprint/land speed bike
JMR Racing CB750A street ET drag bike

Offline Howell

  • Honda the power of dreams
  • Hot Shot
  • ***
  • Posts: 573
    • CB500 classic racing
Re: sohc f2 head
« Reply #5 on: December 11, 2012, 01:18:15 PM »
Difference K and F2:
Logged
You meet the nicest people on a Honda

Offline bear

  • Vale Bill McIntosh ......"illegitimi non carborundum"
  • Old Timer
  • ******
  • Posts: 2,575
  • Leeton in Australia
Re: sohc f2 head
« Reply #6 on: December 11, 2012, 05:12:10 PM »
We have found that the F2 head is the best option for us.
We use comp. S/S valves from an EVO8.
35mm in. and 30mm exh.
Some machining is required but nothing a good head man can't handle.
The Mega 125-70/75 is the go with the head mods mentioned above, it has good lift and short duration.
We set the timing with 5deg. more advance than suggested on the timing card, this brings the curve down to a more usable rev range for the chairs.
PM if you would like more details.

Cheers,
Brian
« Last Edit: December 11, 2012, 05:15:20 PM by bear »
Logged
The older I get the faster I was.

Offline Jerry Rxman Griffin aka MuthaF'er

  • This MuthaF'er is getting to be a
  • Really Old Timer ...
  • *******
  • Posts: 14,902
  • Bought her new 4/75
Re: sohc f2 head
« Reply #7 on: December 11, 2012, 08:02:17 PM »
If you have the complete F2 top end I'd go with that. The larger valves will breathe better.

Howell, great compilation of info! What is the source for that?
Logged
As of today 3/13/2012 my original owner 75 CB750F has made it through 3 wives, er EX-wives. Free at last.  ;-)

Offline cbr954

  • Hot Shot
  • ***
  • Posts: 402
Re: sohc f2 head
« Reply #8 on: December 11, 2012, 08:07:07 PM »
Cycle X has that sheet up on there website but I think that is from Action Fours???  I am not sure of that though.
Logged
03 CBR954RR, 72 750 chopper(970cc
F2 head), 2017 CRF450R, 2001 CR250R, 72 CB500, 79 XR250, 04 CRF50,70's soon to be rebuilt cb750 drag bike.

Offline dragracer

  • Really Old Timer ...
  • *******
  • Posts: 5,101
  • CB750F Dragbike
Re: sohc f2 head
« Reply #9 on: December 12, 2012, 06:14:42 AM »
Stupid question, whats an EVO8?????


Quote from: bear on December 11, 2012, 05:12:10 PM
We have found that the F2 head is the best option for us.
We use comp. S/S valves from an EVO8.
35mm in. and 30mm exh.
Some machining is required but nothing a good head man can't handle.
The Mega 125-70/75 is the go with the head mods mentioned above, it has good lift and short duration.
We set the timing with 5deg. more advance than suggested on the timing card, this brings the curve down to a more usable rev range for the chairs.
PM if you would like more details.

Cheers,
Brian
Logged

Offline Tintop

  • Old Timer
  • ******
  • Posts: 3,965
Re: sohc f2 head
« Reply #10 on: December 12, 2012, 07:21:44 AM »
My quess would be a Mitsubishi EVO.
Logged
1977 CB550/4 Cafe - Speed Warrior / BOTM 03/11
1980 CB750F (project)
Whittaker GBF Vintage Racing Sidecar (XS750 power) - ITG / 151's / CMR Racing Products (SOLD)
1976 CB400 SS - stock / BOTM 04/11 (SOLD)
1973 CB750 K - basket case (SOLD)
77 CB550 Cafe build
550/750 Filter Thread
Sidecar Rebuild Thread

Offline johno

  • Expert
  • ****
  • Posts: 1,314
Re: sohc f2 head
« Reply #11 on: December 12, 2012, 11:48:32 AM »
 Mitsubishi  it is , I used the same valves on the hi port head.
johno
Logged
GRASSHOPPER SOHC HONDAS ARE THE MEANING OF LIFE.

Offline dragracer

  • Really Old Timer ...
  • *******
  • Posts: 5,101
  • CB750F Dragbike
Re: sohc f2 head
« Reply #12 on: December 12, 2012, 08:10:19 PM »
Quote from: johno on December 12, 2012, 11:48:32 AM
Mitsubishi  it is , I used the same valves on the hi port head.
johno

Can i assume that the stem size on the EVO valve is the same as stock F2 stems???
Logged

Offline dragracer

  • Really Old Timer ...
  • *******
  • Posts: 5,101
  • CB750F Dragbike
Re: sohc f2 head
« Reply #13 on: December 12, 2012, 08:52:06 PM »
I researched a few sites and confirmed the stem diameter is close. I have not measured the length of the stock F2 valve yet. Hopefully its a lot shorter than the EVO valve so theres room for a new keeper groove.

http://www.racecomponentsinc.com/Evolution-Evo_VII_IX_Intake_and_Exhaust_valves_1mm.html
Logged

Offline johno

  • Expert
  • ****
  • Posts: 1,314
Re: sohc f2 head
« Reply #14 on: December 14, 2012, 04:43:12 AM »
captain dragracer  :D

I will be back home on Monday, I'll take some pics of them and specs to fit etc and send to you if your interested. Stems a touch bigger but For the larger bore brigade they allow you to run an average port diam of around 31.5mm with good air velocity up from 30.6mm with a 34mm valve.    Still why worry ! just put evan bigger valves in and run a sprocket as big as the wheel ;D ;D ;D
 Begs the question! whats the biggest inlet valve anyone has run or heard of being run ?  ( apart from captain Ken at Cycle x new beast) ;)
johno
Logged
GRASSHOPPER SOHC HONDAS ARE THE MEANING OF LIFE.

Offline Jerry Rxman Griffin aka MuthaF'er

  • This MuthaF'er is getting to be a
  • Really Old Timer ...
  • *******
  • Posts: 14,902
  • Bought her new 4/75
Re: sohc f2 head
« Reply #15 on: December 14, 2012, 03:46:53 PM »
Have we told anyone the secret intake size of the NEW CycleX head?!?!
Logged
As of today 3/13/2012 my original owner 75 CB750F has made it through 3 wives, er EX-wives. Free at last.  ;-)

Offline cbr954

  • Hot Shot
  • ***
  • Posts: 402
Re: sohc f2 head
« Reply #16 on: December 14, 2012, 05:21:18 PM »
website says 38mm intake  32mm exhaust.
Logged
03 CBR954RR, 72 750 chopper(970cc
F2 head), 2017 CRF450R, 2001 CR250R, 72 CB500, 79 XR250, 04 CRF50,70's soon to be rebuilt cb750 drag bike.

Offline Jerry Rxman Griffin aka MuthaF'er

  • This MuthaF'er is getting to be a
  • Really Old Timer ...
  • *******
  • Posts: 14,902
  • Bought her new 4/75
Re: sohc f2 head
« Reply #17 on: December 14, 2012, 05:44:00 PM »
And it's true. Does it say the intake runners are set up for 40mm carbs?
Logged
As of today 3/13/2012 my original owner 75 CB750F has made it through 3 wives, er EX-wives. Free at last.  ;-)

Offline dragracer

  • Really Old Timer ...
  • *******
  • Posts: 5,101
  • CB750F Dragbike
Re: sohc f2 head
« Reply #18 on: December 14, 2012, 06:10:57 PM »
Heck, i even got to touch it in person. I'm still dreaming about that head!!
Logged

Offline dragracer

  • Really Old Timer ...
  • *******
  • Posts: 5,101
  • CB750F Dragbike
Re: sohc f2 head
« Reply #19 on: December 14, 2012, 06:18:15 PM »
Quote from: johno on December 14, 2012, 04:43:12 AM
captain dragracer  :D

I will be back home on Monday, I'll take some pics of them and specs to fit etc and send to you if your interested. Stems a touch bigger but For the larger bore brigade they allow you to run an average port diam of around 31.5mm with good air velocity up from 30.6mm with a 34mm valve.    Still why worry ! just put evan bigger valves in and run a sprocket as big as the wheel ;D ;D ;D
 Begs the question! whats the biggest inlet valve anyone has run or heard of being run ?  ( apart from captain Ken at Cycle x new beast) ;)
johno

Sir Johno.

I would be most honored if you would kindly share the information on using the EVO valves in an "F" head. My email address is; NEXTPLAIN@aol.com. I cannot afford to buy or duplicate one of those CycleX heads but if there is a chance to do some affordable mods to mine like the use of the larger EVO stainless valves, I will surely pursue that option to the best of my financial ability. The only drawback is the need for stiffer springs to keep those heavier valves from bouncing off the seat and the impact to my current cam tower set up. But then, CycleX already has a fix for that one too. 
Logged

Offline MRieck

  • Really Old Timer ...
  • *******
  • Posts: 10,560
  • Big ideas....
Re: sohc f2 head
« Reply #20 on: December 15, 2012, 05:26:52 AM »
Not to be a buzzkill but those valves are real heavy. I have had the stock size F2 valves made up with 5mm stems (with the stock tulip)....they are still heavy. One problem I found was valve to valve clearance with a real big cam with a lot of overlap. Another problem was getting enough spring with Kibblewhite 5mm guides. That was for an LSR engine but drag racing is the same. If anything I'd go to a 36mm intake (changing the seat) and shrink the exhaust valve (changing the seat again). The F2 port could handle the 36 intake. But where do you get new F2 carb manifolds???????? ;D ;D ;D
Logged
Owner of the "Million Dollar CB"

Offline dragracer

  • Really Old Timer ...
  • *******
  • Posts: 5,101
  • CB750F Dragbike
Re: sohc f2 head
« Reply #21 on: December 15, 2012, 07:35:22 AM »
Die grinder????
Logged

Offline dragracer

  • Really Old Timer ...
  • *******
  • Posts: 5,101
  • CB750F Dragbike
Re: sohc f2 head
« Reply #22 on: December 15, 2012, 07:43:28 AM »
Mike,

I felt that weight would be a big issue so the correct seat pressure is extremely important. Finding the right springs could be an issue.  Good point on the valve to valve problem.

Lots to think about and experiment with at this point. It could be time to invest in some equipment and find a few old heads to play with.
Logged

Offline MRieck

  • Really Old Timer ...
  • *******
  • Posts: 10,560
  • Big ideas....
Re: sohc f2 head
« Reply #23 on: December 15, 2012, 08:56:55 AM »
Quote from: dragracer on December 15, 2012, 07:35:22 AM
Die grinder????
Yes....that would work Frank. ;D ;D
Logged
Owner of the "Million Dollar CB"

Offline MRieck

  • Really Old Timer ...
  • *******
  • Posts: 10,560
  • Big ideas....
Re: sohc f2 head
« Reply #24 on: December 15, 2012, 10:09:31 AM »
Quote from: dragracer on December 15, 2012, 07:43:28 AM
Mike,

I felt that weight would be a big issue so the correct seat pressure is extremely important. Finding the right springs could be an issue.  Good point on the valve to valve problem.

Lots to think about and experiment with at this point. It could be time to invest in some equipment and find a few old heads to play with.
I agree THOUGH you could use Ti. ;) ;D
Logged
Owner of the "Million Dollar CB"
Pages: [1] 2  All   Go Up
« previous next »