« previous next »
Pages: [1]   Go Down

Author Topic: Comstar trueing  (Read 2080 times)

0 Members and 1 Guest are viewing this topic.

Rocking-M

  • Guest
Comstar trueing
« on: July 19, 2006, 04:37:06 PM »
I posted earlier about a bent wheel, but it's not bent I think.
Just needs trueing. Can this be done to the Comstar?
Should most any motorcycle shop be able to handle it?

Or has anyone come up with a method to do it yourself?

Thanks, Robert
Logged

Offline cb650

  • Old Timer
  • ******
  • Posts: 3,864
Re: Comstar trueing
« Reply #1 on: July 19, 2006, 05:06:27 PM »
I dont think they can be trued. 



                   Terry   
Logged
18 grand and 18 miles dont make you a biker

Offline ofreen

  • Old Timer
  • ******
  • Posts: 4,060
Re: Comstar trueing
« Reply #2 on: July 19, 2006, 06:11:32 PM »
They can be trued if not bent too badly.  A shop near Seatac mall between Seattle and Tacoma, Washington did two Comstar wheels from a CB900F for me a few years ago, and they turned out fine.  Sorry, can't remember the name of the shop.  They also straightened frames.  If I come up with the name, I'll post it.
Logged
Greg
'75 CB750F

"I would rather have questions I cannot answer than answers I cannot question." - Dr. Wei-Hock Soon

Rocking-M

  • Guest
Re: Comstar trueing
« Reply #3 on: July 19, 2006, 06:24:38 PM »
Thanks Ofreen, my front isn't to bad, very slight wooble and the only reason I really noticed it
was slightly more vibration than I remembered from my last 750.(That was an 16 year memory too ;)
I'm sure if they can do it out there I ought to be able to find someone round here nearby.
Logged

Offline Killer Canary

  • Master
  • *****
  • Posts: 1,805
  • Typical Bran Muffin
Re: Comstar trueing
« Reply #4 on: July 19, 2006, 07:09:39 PM »
My experience with a bad ComStar was that the guy at the tire shop(automotive) told me the wheel had trued easily, but would run out of true again because the oval headed bolts at the hub weren't holding anymore. Before I put the wheel back on the bike( after truing) I ground off one of the hub nuts, replaced with hex head bolt and nut, torqued it down, ground off the next, etc. until all had been replaced. It never caused a problem again.
Logged
If it's worth doing at all it's worth over-doing.
Honda MT250, CB400F, CB450K, CB550, GL500, CBR929
Kawi GPz900, H1

Rocking-M

  • Guest
Re: Comstar trueing
« Reply #5 on: July 20, 2006, 12:23:54 PM »
Thanks Killer, I spent a bit of time while through town today hunting for a shop that could do it.
Started to leave it at the new race shop but decide if he was going to have to experiment well I could do that.
I have a borrowed old bike truing stand, and my comstars have bolts already. The nuts were tack welded to
keep them from backing off, i'll grind it off and loosen and go from there.
I'll post how it turns out.
Logged

Rocking-M

  • Guest
Re: Comstar trueing
« Reply #6 on: July 20, 2006, 06:53:13 PM »
Ground off the tack welds and loosend the bolts, fussed with the wheel bumping it back and
forth with a rubber hammer till I got it. Runs true now. Not to bad a job. Even fixed the
29 year old sticking calipers on the front. Thanks for the advice.
Logged
Pages: [1]   Go Up
« previous next »