« previous next »
Pages: 1 [2] 3 4 ... 7   Go Down

Author Topic: Stilltime's CB550 Project  (Read 25997 times)

0 Members and 1 Guest are viewing this topic.

Offline Stilltime

  • Hot Shot
  • ***
  • Posts: 353
  • Building my Dream
Re: Stilltime's CB550 Project
« Reply #25 on: February 28, 2014, 10:40:20 AM »
Swapped my tires over to the new (to me) wheels, gloss black rims and hubs, polished spokes...

Drained the tank, and dropped off the tank and side covers for paint, and everything else for powdercoat.  Can't wait to see the new paint job, the brushed on bedliner was getting old!

Ditched the reservoir that came with my Nissin brake lever in place of this nice billet mini reservoir.
Logged
'78 CB550 - Orange Crush

Offline Stilltime

  • Hot Shot
  • ***
  • Posts: 353
  • Building my Dream
Re: Stilltime's CB550 Project
« Reply #26 on: February 28, 2014, 10:43:33 AM »
Drilled and tapped the swingarm to mount spools.  I never had the center mount so this should make rear wheel and chain service a little simpler.

Started designing a bolt-on rear subframe, Harisluv bent the tube and it looks great!  Hopefully will be fabricating the rest this week.

Debating whether or not I will like this fairing with my TRS HID kit installed behind it...
Logged
'78 CB550 - Orange Crush

Offline Stilltime

  • Hot Shot
  • ***
  • Posts: 353
  • Building my Dream
Re: Stilltime's CB550 Project
« Reply #27 on: February 28, 2014, 10:46:08 AM »
Picked up all the parts from the powdercoater.  Everything turned out amazing, the level of detail they went to is awesome.  This will REALLY transform the look of the bike.
Logged
'78 CB550 - Orange Crush

Offline Stilltime

  • Hot Shot
  • ***
  • Posts: 353
  • Building my Dream
Re: Stilltime's CB550 Project
« Reply #28 on: February 28, 2014, 10:48:13 AM »
Installed 14" Progressives (my stock length set with ~1000mi will be for sale soon).  No pictures yet of these.

Seriously love the powdercoat, can't wait to get it all back together.  This is where I'm at, I'll be updating this a lot more frequently from now on!
Logged
'78 CB550 - Orange Crush

Offline Maurice

  • Hot Shot
  • ***
  • Posts: 450
Re: Stilltime's CB550 Project
« Reply #29 on: February 28, 2014, 11:29:22 AM »
Quote from: Stilltime on February 28, 2014, 10:37:02 AM
Thanks!  Maurice - I designed it to mate up to the stock air plenum, replacing the rear section that houses the filter.  Had it 3D printed and used it for a few months.  Really worked great.  Was worried it would crack but when I pulled it off to install the velocity stacks, there were no issues.  Not planning on letting go of it yet...

Any chance you could have another one printed out :) ? In black? That is one swell idea.
Logged

Offline Stilltime

  • Hot Shot
  • ***
  • Posts: 353
  • Building my Dream
Re: Stilltime's CB550 Project
« Reply #30 on: February 28, 2014, 11:33:13 AM »
You can print them right from Shapeways, I made the design available to public.  Only downside is that it'll run you ~$90...  (Nothing goes to me, that's their cost)  I can send the link if you're still interested!
Logged
'78 CB550 - Orange Crush

Offline Maurice

  • Hot Shot
  • ***
  • Posts: 450
Re: Stilltime's CB550 Project
« Reply #31 on: February 28, 2014, 11:37:04 AM »
Quote from: Stilltime on February 28, 2014, 11:33:13 AM
You can print them right from Shapeways, I made the design available to public.  Only downside is that it'll run you ~$90...  (Nothing goes to me, that's their cost)  I can send the link if you're still interested!

Well, sure. Looks like it would be useful for other things as well. Thanks

Still drooling over the pictures.
Logged

Offline Trad

  • Expert
  • ****
  • Posts: 964
Re: Stilltime's CB550 Project
« Reply #32 on: February 28, 2014, 11:54:57 AM »
Those pieces turned out great! I kind of wish I had used powdercoat for a lot of the engine pieces and frame on my build. Instead I just kept things raw media blasted alloy, brushed alloy, and Semi-Gloss automotive paint. Decided to use those funds elsewhere. Definitely subscribed here.

-JJ
Logged
74 CB550 Build: NOS-GUTTED-OEMplus-HOLDTRUE
http://forums.sohc4.net/index.php/topic,130575.0.html

Offline Stilltime

  • Hot Shot
  • ***
  • Posts: 353
  • Building my Dream
Re: Stilltime's CB550 Project
« Reply #33 on: February 28, 2014, 12:01:07 PM »
Logged
'78 CB550 - Orange Crush

Offline Stilltime

  • Hot Shot
  • ***
  • Posts: 353
  • Building my Dream
Re: Stilltime's CB550 Project
« Reply #34 on: February 28, 2014, 12:03:20 PM »
Trad, I wanted to try to paint as much as possible myself, but didn't end up getting started with this project heavily until January.  This winter has been BRUTAL cold, and without a heated garage I decided to have a pro finish them.  All in all I'm glad I went with powder, but the invoice hurt a little.
Logged
'78 CB550 - Orange Crush

Offline sourjon

  • Full Member
  • *
  • Posts: 10
Re: Stilltime's CB550 Project
« Reply #35 on: February 28, 2014, 01:04:02 PM »
Sweet. Subscribed.

John
Logged

Offline Stilltime

  • Hot Shot
  • ***
  • Posts: 353
  • Building my Dream
Re: Stilltime's CB550 Project
« Reply #36 on: February 28, 2014, 01:29:38 PM »
Going to send my rotors off to Truedisk to get this pattern drilled, then surface ground.

For everything I have removed, I have ordered button head stainless metric hardware to replace it, except for a few high strength areas like the rotor and caliper where hex heads will be used.
Logged
'78 CB550 - Orange Crush

Offline iron_worker

  • Master
  • *****
  • Posts: 2,081
Re: Stilltime's CB550 Project
« Reply #37 on: February 28, 2014, 02:46:44 PM »
The powder coater did an excellent job on your parts.  8)

IW
Logged

Offline Stilltime

  • Hot Shot
  • ***
  • Posts: 353
  • Building my Dream
Re: Stilltime's CB550 Project
« Reply #38 on: March 03, 2014, 05:57:00 PM »
Thanks!  I thought so too.  Got a sneak peek at the tank, side covers and points cover.  They aren't finished yet, still another surprise to come!  The color is Honda Orange Burst Metallic.
Logged
'78 CB550 - Orange Crush

Offline zenocchio

  • Enthusiast
  • **
  • Posts: 123
Re: Stilltime's CB550 Project
« Reply #39 on: March 03, 2014, 09:15:44 PM »
great build!
and great fab skills too!
Logged

Offline Stilltime

  • Hot Shot
  • ***
  • Posts: 353
  • Building my Dream
Re: Stilltime's CB550 Project
« Reply #40 on: March 04, 2014, 07:43:45 PM »
Started on carb reassembly while my wife worked on some paperwork.
Logged
'78 CB550 - Orange Crush

Offline RodPlunger

  • Annoying New Guy...
  • Full Member
  • *
  • Posts: 95
  • The road goes on forever....
Re: Stilltime's CB550 Project
« Reply #41 on: March 04, 2014, 08:25:10 PM »
That K/N adapter is fantastic. Did you like how it ran? I am slightly opposed to running pods as I want to use the bike as a daily driver, so the idea of the K/N filter replacement is great. But, why do they charge so much different for the black plastic over the white? Rats.
Logged
1977 CB550F Supersport

"We want to be free.
We want to be free to do what we want to do.
We want to be free to ride.
We want to be free to ride our machines without being hassled by The Man...
And we want to get loaded!

Offline Stilltime

  • Hot Shot
  • ***
  • Posts: 353
  • Building my Dream
Re: Stilltime's CB550 Project
« Reply #42 on: March 06, 2014, 03:19:50 PM »
I felt that it ran every bit as good as the stock airbox when I had it mounted.  Would run it again, except I love my SDP velocity stacks haha.  My guess is that the white material is the natural color, and they have to add ($20 worth???) of black dye to make the black parts.  You could always buy the white one and paint it!
Logged
'78 CB550 - Orange Crush

Offline Stilltime

  • Hot Shot
  • ***
  • Posts: 353
  • Building my Dream
Re: Stilltime's CB550 Project
« Reply #43 on: March 06, 2014, 03:23:28 PM »
Received my rotor from TrueDisc LLC today.  I shipped it last Saturday, so very quick turnaround for drilling and surfacing.

The pattern was supposed to look like the one I posted earlier.  There was a programming error and it started to drill the second hole in the wrong direction, so they had to do the whole pattern like a check mark.  Now that I see it, it isn't as bad as it sounded when Tom emailed me (and was willing to make it right if I wasn't happy, very good service), but I am still slightly bummed that it isn't the pattern I wanted...oh well.
Logged
'78 CB550 - Orange Crush

Offline Stilltime

  • Hot Shot
  • ***
  • Posts: 353
  • Building my Dream
Re: Stilltime's CB550 Project
« Reply #44 on: March 06, 2014, 08:22:57 PM »
Got the carbs back together...but not before the sharp corner of the manifold sliced my hand open!
Logged
'78 CB550 - Orange Crush

Offline SOHC4 Cafe Racer Fan

  • Speak up, Whipper-Snapper! I'm a
  • Really Old Timer ...
  • *******
  • Posts: 15,731
  • SOHC/4 Member #1235
Re: Stilltime's CB550 Project
« Reply #45 on: March 06, 2014, 10:43:15 PM »
Quote from: Stilltime on March 06, 2014, 03:23:28 PM
Received my rotor from TrueDisc LLC today.  I shipped it last Saturday, so very quick turnaround for drilling and surfacing.

The pattern was supposed to look like the one I posted earlier.  There was a programming error and it started to drill the second hole in the wrong direction, so they had to do the whole pattern like a check mark.  Now that I see it, it isn't as bad as it sounded when Tom emailed me (and was willing to make it right if I wasn't happy, very good service), but I am still slightly bummed that it isn't the pattern I wanted...oh well.

Check the box!  I would figure a way to drill a new disc.  That will bug you for years if you keep it.
Logged
1975 CB550K1 "Blue" Stockish Restomod (http://forums.sohc4.net/index.php?topic=135005.0)
1975 CB550F1 frame/CB650 engine hybrid "The Hot Mess" (http://forums.sohc4.net/index.php/topic,150220.0.html)
2008 Triumph Thruxton (http://forums.sohc4.net/index.php/topic,190956.0.html)
2014 MV Agusta Brutale Dragster 800
2015 Yamaha FZ-09 (http://forums.sohc4.net/index.php/topic,186861.0.html)

"There are some things nobody needs in this world, and a bright-red, hunch-back, warp-speed 900cc cafe racer is one of them — but I want one anyway, and on some days I actually believe I need one.... Being shot out of a cannon will always be better than being squeezed out of a tube. That is why God made fast motorcycles, Bubba." Hunter S. Thompson, Song of the Sausage Creature, Cycle World, March 1995.  (http://www.latexnet.org/~csmith/sausage.html and https://magazine.cycleworld.com/article/1995/3/1/song-of-the-sausage-creature)

Sold/Emeritus
1973 CB750K2 "Bionic Mongrel" (http://forums.sohc4.net/index.php?topic=132734.0) - Sold
1977 CB750K7 "Nine Lives" Restomod (http://forums.sohc4.net/index.php?topic=50490.0) - Sold
2005 RVT1000RR RC51-SP2 "El Diablo" - Sold
2016+ Triumph Thruxton 1200 R (http://forums.sohc4.net/index.php/topic,170198.0.html) - Sold

Offline Stilltime

  • Hot Shot
  • ***
  • Posts: 353
  • Building my Dream
Re: Stilltime's CB550 Project
« Reply #46 on: March 07, 2014, 07:18:16 AM »
Luckily I powdercoated both rotors but only sent one...I might see if they'll drill the second rotor for free or something...the way I wanted it to begin with.

I'm too anal to just be okay with it.  If the additional hole was centered between the two lines, it might have been fine but as it is it looks completely out of place.
Logged
'78 CB550 - Orange Crush

Offline Trad

  • Expert
  • ****
  • Posts: 964
Re: Stilltime's CB550 Project
« Reply #47 on: March 07, 2014, 08:48:44 AM »
In all honesty, I think the added hole looks fine. I had to look pretty hard to see any kind of error.......If that's any consolation  ;)
« Last Edit: March 07, 2014, 09:20:56 AM by Trad »
Logged
74 CB550 Build: NOS-GUTTED-OEMplus-HOLDTRUE
http://forums.sohc4.net/index.php/topic,130575.0.html

Offline SOHC4 Cafe Racer Fan

  • Speak up, Whipper-Snapper! I'm a
  • Really Old Timer ...
  • *******
  • Posts: 15,731
  • SOHC/4 Member #1235
Re: Stilltime's CB550 Project
« Reply #48 on: March 07, 2014, 08:53:05 AM »
I agree that it's a matter of personal taste.  Many folks would not notice or not let it bother them.  I'm one of those people where it would bug me too much.  The good news is that you have a spare and he can drill and resurface that one to make up for the other one.
Logged
1975 CB550K1 "Blue" Stockish Restomod (http://forums.sohc4.net/index.php?topic=135005.0)
1975 CB550F1 frame/CB650 engine hybrid "The Hot Mess" (http://forums.sohc4.net/index.php/topic,150220.0.html)
2008 Triumph Thruxton (http://forums.sohc4.net/index.php/topic,190956.0.html)
2014 MV Agusta Brutale Dragster 800
2015 Yamaha FZ-09 (http://forums.sohc4.net/index.php/topic,186861.0.html)

"There are some things nobody needs in this world, and a bright-red, hunch-back, warp-speed 900cc cafe racer is one of them — but I want one anyway, and on some days I actually believe I need one.... Being shot out of a cannon will always be better than being squeezed out of a tube. That is why God made fast motorcycles, Bubba." Hunter S. Thompson, Song of the Sausage Creature, Cycle World, March 1995.  (http://www.latexnet.org/~csmith/sausage.html and https://magazine.cycleworld.com/article/1995/3/1/song-of-the-sausage-creature)

Sold/Emeritus
1973 CB750K2 "Bionic Mongrel" (http://forums.sohc4.net/index.php?topic=132734.0) - Sold
1977 CB750K7 "Nine Lives" Restomod (http://forums.sohc4.net/index.php?topic=50490.0) - Sold
2005 RVT1000RR RC51-SP2 "El Diablo" - Sold
2016+ Triumph Thruxton 1200 R (http://forums.sohc4.net/index.php/topic,170198.0.html) - Sold

Offline Trad

  • Expert
  • ****
  • Posts: 964
Re: Stilltime's CB550 Project
« Reply #49 on: March 07, 2014, 09:21:11 AM »
Quote from: CB750 Cafe Racer Fan on March 07, 2014, 08:53:05 AM
I agree that it's a matter of personal taste.  Many folks would not notice or not let it bother them.  I'm one of those people where it would bug me too much.  The good news is that you have a spare and he can drill and resurface that one to make up for the other one.

Agreed.
Logged
74 CB550 Build: NOS-GUTTED-OEMplus-HOLDTRUE
http://forums.sohc4.net/index.php/topic,130575.0.html
Pages: 1 [2] 3 4 ... 7   Go Up
« previous next »