« previous next »
Pages: [1]   Go Down

Author Topic: Restoring, but not over-restoring, engine covers?  (Read 2407 times)

0 Members and 2 Guests are viewing this topic.

Offline Scott S

  • Global Moderator
  • Really Old Timer ...
  • *****
  • Posts: 8,232
Restoring, but not over-restoring, engine covers?
« on: August 27, 2013, 07:09:31 PM »
 I know the engine covers were lightly polished and then clear coated from the factory. I've got a place that does awesome aluminum polishing, but what's everybody's trick for simply restoring the covers? Is there a way to bring them back to as close to the factory finish as possible?

Logged
'71 CB500 K0
'17 Triumph Street Scrambler
'81 Yamaha XS650

Offline seanbarney41

  • not really that much younger than an
  • Really Old Timer ...
  • *******
  • Posts: 10,835
Re: Restoring, but not over-restoring, engine covers?
« Reply #1 on: August 27, 2013, 08:09:43 PM »
sand to about 320 grit, then hit 'em with red scotchbrite...this will get you in the ballpark....certainly not concourse.  Also, factory aluminum was clear coated...
Logged
If it works good, it looks good...

Offline bjbuchanan

  • Master
  • *****
  • Posts: 2,276
Re: Restoring, but not over-restoring, engine covers?
« Reply #2 on: August 27, 2013, 08:17:58 PM »
I sand thru the bad crap and then hit them with a wire wheel. I have a dremel and like to use the carbon steel wire wheel, nice light polished look to it.
Logged
The dirty girl-1976 cb750k, Ebay 836, Tracy bodykit
Round top carbs w/ 38 pilots, middle needle position, airscrew 7/8ths out, 122 main jet
Stock airbox w/ drop in K&N, Hooker 4-1

Don't trust me alone with a claw hammer and some pliers

Offline scunny

  • Old Timer
  • ******
  • Posts: 4,618
  • don't call me expert
Re: Restoring, but not over-restoring, engine covers?
« Reply #3 on: August 28, 2013, 12:43:29 AM »
+1 on the scotchbrite, adds a nice brushed look if you aren't into highly polished. then mothers aluminum mag wheel polish to seal it. only have to redo the polish occasionally.
Logged
past-cb100,ts250,cb500,cb500,gs1000,gs650g.phillips traveller
present-CB 650 retro
            VTR1000F3
           XL250S riverbed rocket
           TS250[sold]
           TS185[sold]
           XL125S[sold]
           MT50 (white)
           MT50 (red)[sold]
           KN250/XS400 project
           XR/XL250 bitsa under construction
           SL100[sold]
           XL250R
           pedal(pub bike) leaks oil
my gallery http://gallery.sohc4.net/members/personal/scunny

Offline Scott S

  • Global Moderator
  • Really Old Timer ...
  • *****
  • Posts: 8,232
Re: Restoring, but not over-restoring, engine covers?
« Reply #4 on: August 28, 2013, 03:18:41 AM »
 Cool. I can do that and probably not have to remove the stuff from the bike. Worth a shot, anyway.

 Were the forks done in this same manner?
Logged
'71 CB500 K0
'17 Triumph Street Scrambler
'81 Yamaha XS650

Offline DanJ

  • Enthusiast
  • **
  • Posts: 142
Re: Restoring, but not over-restoring, engine covers?
« Reply #5 on: August 28, 2013, 04:15:47 AM »
A buddy of mine who does some pretty awesome restorations on dirt bikes say polish the hell out of them then sandblast with fine walnut shells.
Logged

Offline flybox1

  • My wife thinks I'm a
  • Really Old Timer ...
  • *******
  • Posts: 14,301
Re: Restoring, but not over-restoring, engine covers?
« Reply #6 on: August 28, 2013, 08:22:56 AM »
Quote from: DanJ on August 28, 2013, 04:15:47 AM
A buddy of mine who does some pretty awesome restorations on dirt bikes say polish the hell out of them then sandblast with fine walnut shells.
kinda sounds backwards...
Logged
'78 750K (F3 engine) PD42b's, Modified airbox w/K&N  filter, 40/110 jets, 1 needle shim, IMS@ 1 turn out. Kerker + Cone 18" QuietCore

Past Bikes
1974 550K0 (stock), 1973 CB350F (stock), 1983 Yamaha XS400K (POS)
77/78 cool 2 member #3
"Knowledge without mileage equals bullsh!t" - Henry Rollins

"This is my CB. There are many like it, but this one is mine…"

Offline TwoTired

  • Really Old Timer ...
  • *******
  • Posts: 21,805
Re: Restoring, but not over-restoring, engine covers?
« Reply #7 on: August 28, 2013, 08:35:08 AM »
Quote from: Scott S on August 27, 2013, 07:09:31 PM
I know the engine covers were lightly polished and then clear coated from the factory.
Half true.  They were certainly clear coated.  But, it was a "brushed" finish.  Like what you get from fine sandpaper or Scothcbrite.

Clear coat won't grab onto highly polished surfaces.  To make the tiny scratches uniformly shallow, they were probably polished first, though.  So deeper grooves from coarser grit didn't alter the final visual effect.
Logged
Lloyd... (SOHC4 #11 Original Mail List)
72 500, 74 550, 75 550K, 75 550F, 76 550F, 77 550F X2, 78 550K, 77 750F X2, 78 750F, 79CX500, 85 700SC, GL1100

Those that learn from history are doomed to repeat it by those that don't learn from history.

Offline DanJ

  • Enthusiast
  • **
  • Posts: 142
Re: Restoring, but not over-restoring, engine covers?
« Reply #8 on: August 28, 2013, 08:44:45 AM »
Quote from: flybox1 on August 28, 2013, 08:22:56 AM
Quote from: DanJ on August 28, 2013, 04:15:47 AM
A buddy of mine who does some pretty awesome restorations on dirt bikes say polish the hell out of them then sandblast with fine walnut shells.
kinda sounds backwards...
I guess the fine walnut just takes the high gloss off and leaves a nice finish. I haven't tried it but the guy does nice work and I have no reason to doubt him.
Logged

Offline Bankerdanny

  • Eventually I will be old enough in reality to be
  • Really Old Timer ...
  • *******
  • Posts: 7,626
  • Endeavor to persevere
Re: Restoring, but not over-restoring, engine covers?
« Reply #9 on: August 28, 2013, 09:10:45 AM »
I got this finish on my drive side case by using 220, then 400, then 600, then 800, then 1,000, then 1,500 grit wet/dry paper and finishing with semi-chrome polish and a buffing wheel on a drill.

Logged
"The problem with quotes on the Internet is that you never know if they're true" - Abraham Lincoln

Current: '76 CB750F. Previous:  '75 CB550F, 2007 Yamaha Vino 125 Scooter, '75 Harley FXE Superglide, '77 GL1000, '77 CB550k, '68 Suzuki K10 80, '68 Yamaha YR2, '69 BMW R69S, '71 Honda SL175, '02 Royal Enfield Bullet 500, '89 Yamaha FJ1200

Offline Scott S

  • Global Moderator
  • Really Old Timer ...
  • *****
  • Posts: 8,232
Re: Restoring, but not over-restoring, engine covers?
« Reply #10 on: August 28, 2013, 05:20:24 PM »
 I took these pics the other night while polishing up some chromed covers that came with my 550F. I realized that they show some NOS, unrestored parts that are a nice example of the stock finish.
 Look at the valve cover end caps in the background. I also have an NOS alternator cover, too.


Logged
'71 CB500 K0
'17 Triumph Street Scrambler
'81 Yamaha XS650

Offline Xnavylfr

  • Expert
  • ****
  • Posts: 1,102
  • Beers, Babes and bikes since 1965
Re: Restoring, but not over-restoring, engine covers?
« Reply #11 on: August 29, 2013, 12:40:45 PM »
If you continue to polish with finer grit sandpaper them use SIMICHROME paste the ALT cover will look just as good as the others. Without some type of wax/polish over the shiny stuff , it will start to corrode pretty quick!!


Xnavylfr(CHUCK)
Logged
Pages: [1]   Go Up
« previous next »