Author Topic: Speedhut gauges! Pictures, questions, comments (Read 9575 times)

Elan · « **Reply #25 on:** September 17, 2013, 01:15:56 pm »

Ya i drew it up and had it done on a waterjet.

bert96 · « **Reply #26 on:** September 17, 2013, 01:47:19 pm »

And for those who are worry about the 15' foot gps antenna,i asked if it was possible to have it shorter and they said yes, it's only a 10$ option!

Bert

Stilltime · « **Reply #27 on:** September 17, 2013, 03:48:49 pm »

Quote from: bert96 on September 17, 2013, 07:30:38 am

I don't want to hijack,but i want to buy speedhut gauges too and i was wondering if there is a place cheaper to buy these gauges other than their web site?

Thanks

Bert

Whoops, everyone else beat me to it! Buy during their holiday sales...

I had them reverse my GPS Speedo and Tach so that the large sweeping needle is the tach and the tiny one on the right is the speedo. Just a personal preference, but they had no problem changing it.

Stilltime · « **Reply #28 on:** September 17, 2013, 03:58:25 pm »

Better shot of the gauge

ncstatecamp · « **Reply #29 on:** September 17, 2013, 04:10:49 pm »

Quote from: Elan on September 17, 2013, 01:15:56 pm

Ya i drew it up and had it done on a waterjet.

How much did that run you?

Elan · « **Reply #30 on:** September 17, 2013, 06:15:59 pm »

Quote from: ncstatecamp on September 17, 2013, 04:10:49 pm

Quote from: Elan on September 17, 2013, 01:15:56 pm
Ya i drew it up and had it done on a waterjet.

How much did that run you?

bribery at work

ncstatecamp · « **Reply #31 on:** September 17, 2013, 06:18:33 pm »

Quote from: Elan on September 17, 2013, 06:15:59 pm

bribery at work

And how much to bride you to bribe some again? :-)

Elan · « **Reply #32 on:** September 17, 2013, 07:36:52 pm »

Quote from: ncstatecamp on September 17, 2013, 06:18:33 pm

Quote from: Elan on September 17, 2013, 06:15:59 pm

bribery at work

And how much to bride you to bribe some again? :-)

hehehe slim. I've been bugging the guy to do more stuff and he's pretty much just an a$$h01e. But it isnt too expensive. I quoted it on ponoko.com and it was well under 100 shipped. But I think the stainless was on the thin side. But, its an example that you can get it done reasonably.

Elan · « **Reply #33 on:** September 17, 2013, 07:37:36 pm »

Quote from: Elan on September 17, 2013, 07:36:52 pm

Quote from: ncstatecamp on September 17, 2013, 06:18:33 pm
Quote from: Elan on September 17, 2013, 06:15:59 pm

bribery at work

And how much to bride you to bribe some again? :-)

hehehe slim chances. I've been bugging the guy to do more stuff and he's pretty much just an a$$h01e. But it isnt too expensive. I quoted it on ponoko.com and it was well under 100 shipped. But I think the stainless was on the thin side. But, its an example that you can get it done reasonably.

wowbagger · « **Reply #34 on:** September 17, 2013, 08:22:40 pm »

You could swap your unicorn top bridge for a later model bridge with the two gauge mount holes:

then use something like this:

bert96 · « **Reply #35 on:** October 02, 2013, 09:38:50 am »

Look what i have recieved this morning!

Bert

Stilltime · « **Reply #36 on:** October 02, 2013, 10:21:31 am »

Quote from: bert96 on October 02, 2013, 09:38:50 am

Look what i have recieved this morning!

Bert

Awesome!! What are your plans for mounting them?

bert96 · « **Reply #37 on:** October 02, 2013, 10:23:56 am »

Just like Trueblue,

http://forums.sohc4.net/index.php?topic=95342.50

Bert

trueblue · « **Reply #38 on:** October 03, 2013, 02:19:47 am »

Good luck Bert. If you have any questions, just shoot us a PM

.

bert96 · « **Reply #39 on:** October 09, 2013, 05:56:22 am »

You have fit a sensor on your front wheel right? i thought on install mine on the rear wheel(i bought speed sensor from a GMC truck)

What is your gap? i don't need a magnet i think?

Bert

Elan · « **Reply #40 on:** October 09, 2013, 08:41:58 am »

Quote from: bert96 on October 09, 2013, 05:56:22 am

You have fit a sensor on your front wheel right? i thought on install mine on the rear wheel(i bought speed sensor from a GMC truck)

What is your gap? i don't need a magnet i think?

Bert

You don't need a sensor, at least on mine. Does your's have GPS?

bert96 · « **Reply #41 on:** October 09, 2013, 09:18:20 am »

no gps...

Bert

Elan · « **Reply #42 on:** October 09, 2013, 09:31:55 am »

ahhh ok

trueblue · « **Reply #43 on:** October 10, 2013, 03:22:50 am »

Bert I went to the bike wreckers and got a speedo drive and pick up off a VFR750, it needed to be thinned down 0.100" to fit between the fork leg and wheel. The two speed pickup wires from the guage just plug into the two wires from the sensor.

Stilltime · « **Reply #44 on:** October 10, 2013, 04:22:53 pm »

Started making a new dash plate for mine...

ncstatecamp · « **Reply #45 on:** October 13, 2013, 05:11:32 pm »

Quote from: bert96 on October 09, 2013, 05:56:22 am

You have fit a sensor on your front wheel right? i thought on install mine on the rear wheel(i bought speed sensor from a GMC truck)

What is your gap? i don't need a magnet i think?

Bert

Depending on the ones he bought. Mine are gps so no sensors needed.

STERRCB750 · « **Reply #46 on:** October 18, 2016, 08:38:10 am »

is the back light always on for your gauge or did you have a switch for it?

ncstatecamp · « **Reply #47 on:** February 06, 2017, 05:30:27 pm »

always on

greenjeans · « **Reply #48 on:** February 07, 2017, 11:07:06 am »

Very timely post.
Just got mine in last night. Very easy to mount - I ordered their clamp mounts ($14 each) If you trim a little off the mount and enlarge the holes, you can use the gauge mounts on the triple. Their clamps are very secure. I really like the idea of mounting them in the original housing, but for this one, I'm wanting a lower profile. They look well made and seems like they would be easy to water-proof enough to keep things dry. They are pricey, but you only live once... as far as I know.

ncstatecamp · « **Reply #49 on:** February 07, 2017, 01:59:27 pm »

Quote from: greenjeans on February 07, 2017, 11:07:06 am

Very timely post.
Just got mine in last night. Very easy to mount - I ordered their clamp mounts ($14 each) If you trim a little off the mount and enlarge the holes, you can use the gauge mounts on the triple. Their clamps are very secure. I really like the idea of mounting them in the original housing, but for this one, I'm wanting a lower profile. They look well made and seems like they would be easy to water-proof enough to keep things dry. They are pricey, but you only live once... as far as I know.

They're well made and life time warranty, I did have something burn out where some lights weren't working, sent it into them and they tuned it up good as new.

Sent from my Nexus 6P using Tapatalk

News:

Author Topic: Speedhut gauges! Pictures, questions, comments (Read 9575 times)