« previous next »
Pages: [1]   Go Down

Author Topic: mom's 72 cb350g  (Read 4887 times)

0 Members and 2 Guests are viewing this topic.

Offline SF

  • Hot Shot
  • ***
  • Posts: 527
  • I burn gas very well
mom's 72 cb350g
« on: March 26, 2014, 09:07:19 AM »
hey guys/gals 5 yrs ago I finally got my hands on my moms green 72 cb350 that she has had since new 17143mi. its been through a few family members from Ontario to Nova Scotia and beat pretty good so ive decided to do a complete resto on it. This is my first resto and I'd like to thank everybody on this forum for documenting their builds that I have learned from. So far this is what's been done.

rebuilt the motor
      -new seals/gaskets/bearings/bushings
      -1st over piston/rings
      -replaced 1 bent exhaust valve
      -new cam chain tensioner/roller
      -neutral switch
      -had the cases blasted and left raw
      -pc frame and etc....
      -cables
      -rubber
      -ceramic coated hubs/headers with repop mufflers
      -rebuilt carbs
      -repainted the tins oem green with metal flake :)
      -lots of new nut/bolts/washers from cmsnl
 
Questions I have,     
 
  I just finished rewire/repair the harness and I would like to know where it is layed out on the frame, it just doesn't look right and I don't have any pics.

I have a 3" ground wire with a washer on each end, not sure but I think it mounts from speedo to tach?

I cant figure out how the kick starter and return spring go back together with new ball and internal spring if found (cant find any info or replacement for the two)

Mods I'm trying,

  -rear grab bar from (550 I think)
  -rear signal stem relocation
  -smaller rear break light
  -redo the seat (foam shave or compress)

pics to follow...

shawn
     
Logged
92 wr250 sold
98 zx6r sold
04 zx10r
73 cb350 twin
75 cb550f
75 cb550f
72 r5c
rgid springer bobber project

Offline FuZZie

  • Expert
  • ****
  • Posts: 1,222
  • If I is expert, I can has cheezburger?
Re: mom's 72 cb350g
« Reply #1 on: March 26, 2014, 09:10:26 AM »
You should have this in "other bikes" SF not new members.  ;)
Logged

Offline SF

  • Hot Shot
  • ***
  • Posts: 527
  • I burn gas very well
Re: mom's 72 cb350g
« Reply #2 on: March 26, 2014, 07:15:37 PM »
Quote from: FuZZie on March 26, 2014, 09:10:26 AM
You should have this in "other bikes" SF not new members.  ;)

Ya I think your right, how do I move a thread??
Logged
92 wr250 sold
98 zx6r sold
04 zx10r
73 cb350 twin
75 cb550f
75 cb550f
72 r5c
rgid springer bobber project

Offline FuZZie

  • Expert
  • ****
  • Posts: 1,222
  • If I is expert, I can has cheezburger?
Re: mom's 72 cb350g
« Reply #3 on: March 26, 2014, 07:23:37 PM »
PM a moderator make sure you include a link to the tread.
Logged

Offline SF

  • Hot Shot
  • ***
  • Posts: 527
  • I burn gas very well
Re: mom's 72 cb350g
« Reply #4 on: March 26, 2014, 07:27:00 PM »
Might as well post the pics
Logged
92 wr250 sold
98 zx6r sold
04 zx10r
73 cb350 twin
75 cb550f
75 cb550f
72 r5c
rgid springer bobber project

Offline SF

  • Hot Shot
  • ***
  • Posts: 527
  • I burn gas very well
Re: mom's 72 cb350g
« Reply #5 on: March 26, 2014, 08:29:24 PM »
#2
Logged
92 wr250 sold
98 zx6r sold
04 zx10r
73 cb350 twin
75 cb550f
75 cb550f
72 r5c
rgid springer bobber project

Offline Stev-o

  • Ain't no
  • Really Old Timer ...
  • *******
  • Posts: 34,399
  • Central Texas
Re: mom's 72 cb350g
« Reply #6 on: March 27, 2014, 06:20:52 AM »
Subscribed.  Tank looks good...
Logged
'74 "Big Bang" Honda 750K [836].....'76 Honda 550F.....K3 Park Racer!......and a Bomber!............plus plus plus.........

Offline SF

  • Hot Shot
  • ***
  • Posts: 527
  • I burn gas very well
Re: mom's 72 cb350g
« Reply #7 on: March 27, 2014, 06:57:08 AM »
more..
Logged
92 wr250 sold
98 zx6r sold
04 zx10r
73 cb350 twin
75 cb550f
75 cb550f
72 r5c
rgid springer bobber project

Offline SF

  • Hot Shot
  • ***
  • Posts: 527
  • I burn gas very well
Re: mom's 72 cb350g
« Reply #8 on: March 27, 2014, 07:02:19 AM »
cant find info on this anywhere, can some one chime in...I think its a signal beeper?
Logged
92 wr250 sold
98 zx6r sold
04 zx10r
73 cb350 twin
75 cb550f
75 cb550f
72 r5c
rgid springer bobber project

Offline Johnie

  • Really Old Timer ...
  • *******
  • Posts: 8,611
Re: mom's 72 cb350g
« Reply #9 on: March 27, 2014, 07:08:41 AM »
Looks like a nice project for you and to keep it in the family is great. If you have trouble finding info or parts you can also check www.hondatwins.net  Lots of good guys there with parts and expertise.
« Last Edit: March 27, 2014, 08:23:01 AM by Johnie »
Logged
1970 CB750K0 - Candy Ruby Red
1973 CB750K3 - Candy Bacchus Olive or Sunflake Orange
1970 Chevy Chevelle SS396 - Cortez Silver
1976 GL1000 Sulphur Yellow

Oshkosh, WI  USA

Offline SF

  • Hot Shot
  • ***
  • Posts: 527
  • I burn gas very well
Re: mom's 72 cb350g
« Reply #10 on: March 27, 2014, 07:11:39 AM »
thanks Johnie
Logged
92 wr250 sold
98 zx6r sold
04 zx10r
73 cb350 twin
75 cb550f
75 cb550f
72 r5c
rgid springer bobber project

Offline SF

  • Hot Shot
  • ***
  • Posts: 527
  • I burn gas very well
Re: mom's 72 cb350g
« Reply #11 on: March 27, 2014, 07:34:22 AM »
can some one tell me where this ground wire goes? I cant find this any where >:(
Logged
92 wr250 sold
98 zx6r sold
04 zx10r
73 cb350 twin
75 cb550f
75 cb550f
72 r5c
rgid springer bobber project

Offline tbpmusic

  • Expert
  • ****
  • Posts: 791
Re: mom's 72 cb350g
« Reply #12 on: March 27, 2014, 08:16:03 AM »
Quote from: SF on March 27, 2014, 07:34:22 AM
can some one tell me where this ground wire goes? I cant find this any where >:(

I think that wire goes from  the handlebar mount to a frame ground.
Without it your handlebars may not ground correctly, and the switches may not work.
Logged
"If you can't fix it with a hammer, then it's an electrical problem"

Bill Lane
 '71 CB450 Mutant/ '75 CB200/ '81 CM200/ '71 C70M

Offline SF

  • Hot Shot
  • ***
  • Posts: 527
  • I burn gas very well
Re: mom's 72 cb350g
« Reply #13 on: March 27, 2014, 12:58:40 PM »
would you know where exactly?
Logged
92 wr250 sold
98 zx6r sold
04 zx10r
73 cb350 twin
75 cb550f
75 cb550f
72 r5c
rgid springer bobber project

Offline tbpmusic

  • Expert
  • ****
  • Posts: 791
Re: mom's 72 cb350g
« Reply #14 on: March 28, 2014, 10:01:40 AM »
Quote from: SF on March 27, 2014, 12:58:40 PM
would you know where exactly?

From part #13/14 in the picture, at the bottom.
It grounds part #3, which grounds the handlebars so your switches work.
Make sure there's no paint where the bars meet #3.
The other end goes to any nearby ground - the existing curves in the wire may give you a clue.



Logged
"If you can't fix it with a hammer, then it's an electrical problem"

Bill Lane
 '71 CB450 Mutant/ '75 CB200/ '81 CM200/ '71 C70M

Offline SF

  • Hot Shot
  • ***
  • Posts: 527
  • I burn gas very well
Re: mom's 72 cb350g
« Reply #15 on: March 28, 2014, 10:06:36 AM »
tbpmusic thanks for the help!  I can see it line up
Logged
92 wr250 sold
98 zx6r sold
04 zx10r
73 cb350 twin
75 cb550f
75 cb550f
72 r5c
rgid springer bobber project

Offline grcamna2

  • Not a
  • Really Old Timer ...
  • *******
  • Posts: 15,207
  • I love to restore & travel. Keep'em Going Strong !
Re: mom's 72 cb350g
« Reply #16 on: March 29, 2014, 03:42:56 PM »
Quote from: tbpmusic on March 27, 2014, 08:16:03 AM
Quote from: SF on March 27, 2014, 07:34:22 AM
can some one tell me where this ground wire goes? I cant find this any where >:(

I think that wire goes from  the handlebar mount to a frame ground.
Without it your handlebars may not ground correctly, and the switches may not work.

That green ground strap(I agree tbp)goes on the bottom of the handlebar(dog bone)mount nut where it tightens down,then bolts to your top triple.I agree that you should scrape paint off of the top triple clamp where it clamps the fork tube for a solid ground.
« Last Edit: March 29, 2014, 03:45:26 PM by grcamna2 »
Logged
75' CB400F/'bunch o' parts' & 81' CB125S modded to a 'CB200S'
  I love the small ones too !
Do your BEST...nobody can take that away from you.

Offline SF

  • Hot Shot
  • ***
  • Posts: 527
  • I burn gas very well
Re: mom's 72 cb350g
« Reply #17 on: March 31, 2014, 12:35:23 PM »
grcamna2-thanks for the input! I have removed powder and sanded every contact point on the bike, cleaned and used dielectric grease on every connection. the last thing I want is to chase grounding issues or ANY issue!
Logged
92 wr250 sold
98 zx6r sold
04 zx10r
73 cb350 twin
75 cb550f
75 cb550f
72 r5c
rgid springer bobber project

Offline SF

  • Hot Shot
  • ***
  • Posts: 527
  • I burn gas very well
Re: mom's 72 cb350g
« Reply #18 on: March 31, 2014, 12:36:49 PM »
Quote from: SF on March 27, 2014, 07:02:19 AM
cant find info on this anywhere, can some one chime in...I think its a signal beeper?


any body know what this is? or better yet where it gets mounted?
Logged
92 wr250 sold
98 zx6r sold
04 zx10r
73 cb350 twin
75 cb550f
75 cb550f
72 r5c
rgid springer bobber project

Offline SF

  • Hot Shot
  • ***
  • Posts: 527
  • I burn gas very well
Re: mom's 72 cb350g
« Reply #19 on: March 31, 2014, 12:59:32 PM »
ceramic hubs not powder
Logged
92 wr250 sold
98 zx6r sold
04 zx10r
73 cb350 twin
75 cb550f
75 cb550f
72 r5c
rgid springer bobber project

Offline grcamna2

  • Not a
  • Really Old Timer ...
  • *******
  • Posts: 15,207
  • I love to restore & travel. Keep'em Going Strong !
Re: mom's 72 cb350g
« Reply #20 on: March 31, 2014, 01:17:45 PM »
They look better than new.
Logged
75' CB400F/'bunch o' parts' & 81' CB125S modded to a 'CB200S'
  I love the small ones too !
Do your BEST...nobody can take that away from you.

Offline SF

  • Hot Shot
  • ***
  • Posts: 527
  • I burn gas very well
Re: mom's 72 cb350g
« Reply #21 on: November 05, 2014, 01:40:55 PM »
been awhile, life in the way and I suck at posting. ive been doing the little things like cables, carbs, exhaust.... polishing signal lenses and a nice little tail light I found. hope to modify the two brackets so it looks narrower, the stock tail is just to big for this 350 IMO and my mom is ok with it so that's good.

 ill post some pics of it along with the signals. I do have a question regarding the exhaust pipe joint collars and their orientation for install maybe some one could chime in.

thanks for looking   
Logged
92 wr250 sold
98 zx6r sold
04 zx10r
73 cb350 twin
75 cb550f
75 cb550f
72 r5c
rgid springer bobber project

Offline SF

  • Hot Shot
  • ***
  • Posts: 527
  • I burn gas very well
Re: mom's 72 cb350g
« Reply #22 on: November 05, 2014, 01:48:07 PM »
can any body tell me if I can change out the 6v bulb in the tail I want to use for a 12v? they are both duel filament. I suspect the 12v would get hotter.
Logged
92 wr250 sold
98 zx6r sold
04 zx10r
73 cb350 twin
75 cb550f
75 cb550f
72 r5c
rgid springer bobber project

Offline grcamna2

  • Not a
  • Really Old Timer ...
  • *******
  • Posts: 15,207
  • I love to restore & travel. Keep'em Going Strong !
Re: mom's 72 cb350g
« Reply #23 on: November 05, 2014, 05:41:19 PM »
Yes,go for the 12 vt.
Logged
75' CB400F/'bunch o' parts' & 81' CB125S modded to a 'CB200S'
  I love the small ones too !
Do your BEST...nobody can take that away from you.

Offline Tugboat

  • Puppet
  • Master
  • *****
  • Posts: 1,778
  • '75 CB750K + '67 CL90 + '71 CT90
    • PseudoMoto
Re: mom's 72 cb350g
« Reply #24 on: November 06, 2014, 08:49:16 AM »
Yes, you can just swap out the bulb. Wires is wires :)
Logged
If it's worth doing, it's worth doing twice.
Pages: [1]   Go Up
« previous next »