« previous next »
Pages: [1]   Go Down

Author Topic: Chains? sprockets??  (Read 951 times)

0 Members and 1 Guest are viewing this topic.

Offline dgilling

  • Hot Shot
  • ***
  • Posts: 343
Chains? sprockets??
« on: April 16, 2014, 03:45:07 PM »
I can't believe how many different opinions there are online about different chain/sprocket setups.  I'm super confused by this point and basically want someone to pick my parts for me.  I have a 77 CB750k.  My stuff is wore out.  I believe I found that the stock setup was a 630 chain with 15/41 sprockets.  Is that true?  My bike does run a little high in the RPMs at 65mph and I would like to improve that.  I'm not a cafe racer and I don't ride the bike a ton.  I just like a good ol sunday cruise.  I see a lot of guys go to 530 chains but some say to stick with 630, what's the real answer here?  is there anything special I'd need to do other than buy 530 chain with 530 sprockets to convert?  Where are you guys buying your chains and sprockets as well?

This is what I'm thinking, a regular 530 chain (no o-rings or special tools needed) with steel front sprocket/aluminum rear and a ratio that cruises good at 65mph.  Thoughts? Blessings?
Logged

Offline flybox1

  • My wife thinks I'm a
  • Really Old Timer ...
  • *******
  • Posts: 14,301
Re: Chains? sprockets??
« Reply #1 on: April 16, 2014, 03:53:32 PM »
a 530 chain is plenty, 110 link,  (not x/o-ring)
DID is a good brand ~$40 for a standard chain
RK is another good brand.
I went with a 17/48 set of JT sprockets and an RK 530 Heavy Duty chain.
« Last Edit: April 16, 2014, 03:57:21 PM by flybox1 »
Logged
'78 750K (F3 engine) PD42b's, Modified airbox w/K&N  filter, 40/110 jets, 1 needle shim, IMS@ 1 turn out. Kerker + Cone 18" QuietCore

Past Bikes
1974 550K0 (stock), 1973 CB350F (stock), 1983 Yamaha XS400K (POS)
77/78 cool 2 member #3
"Knowledge without mileage equals bullsh!t" - Henry Rollins

"This is my CB. There are many like it, but this one is mine…"

Offline Don R

  • My Sandcast is a
  • Really Old Timer ...
  • *******
  • Posts: 19,972
  • Saver of unloved motorcycles.
Re: Chains? sprockets??
« Reply #2 on: April 16, 2014, 04:15:29 PM »
I like the 18/48 for easy cruising, it takes the edge off the rpm's.
Logged
No matter how many times you paint over a shadow, it's still there.
 CEO at the no kill motorcycle shop.
 You don't need a weatherman to know which way the wind blows.

Offline 70CB750

  • Labor omnia vincit improbus.
  • Really Old Timer ...
  • *******
  • Posts: 14,805
  • Northern Virginia
Re: Chains? sprockets??
« Reply #3 on: April 16, 2014, 05:41:43 PM »
I like 17//48 because it moves when I want it to - and I am 250+ pounds.

530 chain is plenty for the bike.
Logged
Prokop
_______________
Pure Gas - find ethanol free gas station near you

I love it when parts come together.

Dorothy - my CB750
CB750K3F - The Red
Sidecar


CB900C

2006 KLR650

Offline Duanob

  • Bold Timer
  • Old Timer
  • ******
  • Posts: 4,009
  • Gotcha!
Re: Chains? sprockets??
« Reply #4 on: April 16, 2014, 08:15:18 PM »
I got a package deal from these guys:
http://www.powersportparts.net/SearchResults.asp?Search=jt

JT sprockets and a japanese 530 chain ( dont remember the brand but its 2 years old and still in good shape)  for a good price delivered.
Logged
"Just because you flush a boatload of money down the toilet, doesn't make the toilet worth more",  My Stepfather the Unknown Poet

1974 CB360T
1976 CB550K2 Resurrected
1976 CB550F2 Barn Find
1979 CX500 VG "HONDA-GUZZI"
2007 Moto Guzzi Breva 750ie
2015 BMW F700GS
Another 1976 CB550K Cafe?

  __o
_- \_<,
(*) /' (*)

Offline dgilling

  • Hot Shot
  • ***
  • Posts: 343
Re: Chains? sprockets??
« Reply #5 on: April 16, 2014, 09:29:12 PM »
This is exactly what I needed. I'm going 530 chain with the ratios mentioned above. Will I need special tools for a non-oring chain?
Logged

Offline PeWe

  • Really Old Timer ...
  • *******
  • Posts: 15,596
  • Bike almost back to the 70's 2015
Re: Chains? sprockets??
« Reply #6 on: April 17, 2014, 02:09:01 AM »
You need a riveting tool if the chain has a rivet link as most of the o-ring/ x-ring chains have
Solid rivet link need very powerful tool like on branded Whale. Hollow rívet link is easier whith plenty of cheaper tools.
Clip link no specific tools except what you probably have, screwdriver + plier
Logged
CB750 K6-76  970cc (Earlier 1005cc JMR Billet block on the shelf waiting for a comeback)
CB750 K2-75 Parts assembled to a stock K2

Updates of the CB750 K6 -1976
http://forums.sohc4.net/index.php/topic,180468.msg2092136.html#msg2092136
The billet block build thread
http://forums.sohc4.net/index.php/topic,49438.msg1863571.html#msg1863571
CB750 K2 -1975  build thread
http://forums.sohc4.net/index.php/topic,168243.msg1948381.html#msg1948381
K2 engine build thread. For a complete CB750 -75
http://forums.sohc4.net/index.php/topic,180088.msg2088008.html#msg2088008
Carb jetting, a long story Mikuni TMR32
http://forums.sohc4.net/index.php/topic,179479.msg2104967.html#msg2104967

Offline flybox1

  • My wife thinks I'm a
  • Really Old Timer ...
  • *******
  • Posts: 14,301
Re: Chains? sprockets??
« Reply #7 on: April 17, 2014, 11:53:18 AM »
Quote from: dgilling on April 16, 2014, 09:29:12 PM
This is exactly what I needed. I'm going 530 chain with the ratios mentioned above. Will I need special tools for a non-oring chain?
nope.  standard chains typically come with clip-type master links.
Logged
'78 750K (F3 engine) PD42b's, Modified airbox w/K&N  filter, 40/110 jets, 1 needle shim, IMS@ 1 turn out. Kerker + Cone 18" QuietCore

Past Bikes
1974 550K0 (stock), 1973 CB350F (stock), 1983 Yamaha XS400K (POS)
77/78 cool 2 member #3
"Knowledge without mileage equals bullsh!t" - Henry Rollins

"This is my CB. There are many like it, but this one is mine…"

Offline dgilling

  • Hot Shot
  • ***
  • Posts: 343
Re: Chains? sprockets??
« Reply #8 on: April 17, 2014, 12:56:12 PM »
how about the rear sprocket material? Alloy or steel? Does alloy wear faster than steel?
Logged

Offline Duanob

  • Bold Timer
  • Old Timer
  • ******
  • Posts: 4,009
  • Gotcha!
Re: Chains? sprockets??
« Reply #9 on: April 17, 2014, 12:59:03 PM »
Original was steel, why not go steel unless you're making a race bike and every lb counts.
Logged
"Just because you flush a boatload of money down the toilet, doesn't make the toilet worth more",  My Stepfather the Unknown Poet

1974 CB360T
1976 CB550K2 Resurrected
1976 CB550F2 Barn Find
1979 CX500 VG "HONDA-GUZZI"
2007 Moto Guzzi Breva 750ie
2015 BMW F700GS
Another 1976 CB550K Cafe?

  __o
_- \_<,
(*) /' (*)

Offline dgilling

  • Hot Shot
  • ***
  • Posts: 343
Re: Chains? sprockets??
« Reply #10 on: April 17, 2014, 01:10:03 PM »
also, is this the type of standard chain we're talking about?  it says 400cc max.

http://www.bikebandit.com/rk-530-rk-m-standard-chain

Logged

Offline dgilling

  • Hot Shot
  • ***
  • Posts: 343
Re: Chains? sprockets??
« Reply #11 on: April 17, 2014, 01:19:22 PM »
I guess a better question is what tensil strength do I need?
Logged

Offline Pat_at_APE

  • Enthusiast
  • **
  • Posts: 171
    • APE Race Parts
Re: Chains? sprockets??
« Reply #12 on: April 17, 2014, 04:32:33 PM »
Considering modern materials and that 1000cc+ bikes now use 530 chain I wouldn't worry about tensile strength with our hp output. 

I'm using 530 chain and the next time I get sprockets I'll get 17 and 47t.  It's lasting great so far.

Regards,
Pat at APE
Logged
Pages: [1]   Go Up
« previous next »