« previous next »
Pages: [1]   Go Down

Author Topic: 79' 650 Cam removal  (Read 1051 times)

0 Members and 4 Guests are viewing this topic.

Offline redrider736

  • Enthusiast
  • **
  • Posts: 168
79' 650 Cam removal
« on: July 08, 2014, 01:42:30 pm »
Purchased  a 79' CB 650 motor for the Oil pan and Cam to put into my 78' CB  550...... I have never removed or opened up a motor until today... Got  the motor out of the frame easy enough,  but not sure how too remove Cam?
Logged
78' CB550k (Not Run'n / Basket Case Project)
77/78 cool 2 member #269

Offline calj737

  • Really Old Timer ...
  • *******
  • Posts: 20,960
  • I refuse...
Re: 79' 650 Cam removal
« Reply #1 on: July 08, 2014, 01:47:10 pm »
Remove tappet covers, release all tension of rockers, remove rocker cover.

Locate cam sprocket. Screws on either edge need to removed, chain slipped off. You need to release tension from cam chain tensioner to create "slack" in the chain first (below carbs, nut on engine). Once chain is slacked, slip chain off, but tie it off from falling into engine. You may need to rotate crank to get to both bolts on sprocket.
Logged
'74 550 Build http://forums.sohc4.net/index.php?topic=126401.0
'73 500 Build http://forums.sohc4.net/index.php?topic=132935.0

"Of all tyrannies, a tyranny sincerely exercised for the good of it's victim may be the most oppressive. It may be better to live under robber barons than under omnipotent moral busybodies. The robber baron's cruelty may sometimes sleep, his cupidity may at some point be satiated, but those who torment us for our own good will torment us without end for they do so with the approval of their own conscience." - C.S. Lewis

Offline goldarrow

  • one day, i'll be an
  • Old Timer
  • ******
  • Posts: 3,361
Re: 79' 650 Cam removal
« Reply #2 on: July 08, 2014, 01:59:06 pm »
If this is good motor, drop it right into the 550 frame???
Logged
Life Is Full Of Challenges - And My Backyard Is Full Of SOHC4's

CB550 K0
CB750 K0, K2, K23 JDM, K45, K5
And the little ones z50r, xr50r, st90


750k5 http://forums.sohc4.net/index.php?topic=114817.0

Offline redrider736

  • Enthusiast
  • **
  • Posts: 168
Re: 79' 650 Cam removal
« Reply #3 on: July 08, 2014, 02:08:13 pm »
Quote from: calj737 on July 08, 2014, 01:47:10 pm
Remove tappet covers, release all tension of rockers, remove rocker cover.

Locate cam sprocket. Screws on either edge need to removed, chain slipped off. You need to release tension from cam chain tensioner to create "slack" in the chain first (below carbs, nut on engine). Once chain is slacked, slip chain off, but tie it off from falling into engine. You may need to rotate crank to get to both bolts on sprocket.

Thanks calj737, just wasn't sure how to get "slack" on the chain..........
« Last Edit: July 08, 2014, 02:16:24 pm by redrider736 »
Logged
78' CB550k (Not Run'n / Basket Case Project)
77/78 cool 2 member #269

Offline redrider736

  • Enthusiast
  • **
  • Posts: 168
Re: 79' 650 Cam removal
« Reply #4 on: July 08, 2014, 02:11:29 pm »
Quote from: goldarrow on July 08, 2014, 01:59:06 pm
If this is good motor, drop it right into the 550 frame???

Don't know when it ran last or really any history from the PO... It didn't come with carbs or exhaust...
« Last Edit: July 08, 2014, 02:14:30 pm by redrider736 »
Logged
78' CB550k (Not Run'n / Basket Case Project)
77/78 cool 2 member #269

Offline Bankerdanny

  • Eventually I will be old enough in reality to be
  • Really Old Timer ...
  • *******
  • Posts: 7,617
  • Endeavor to persevere
Re: 79' 650 Cam removal
« Reply #5 on: July 08, 2014, 02:18:44 pm »
If all you want is the cam, then you can cut the chain off with a cutting wheel, just take care to cut where the chain is not touching the sprocket so you don't damage it.
Logged
"The problem with quotes on the Internet is that you never know if they're true" - Abraham Lincoln

Current: '76 CB750F. Previous:  '75 CB550F, 2007 Yamaha Vino 125 Scooter, '75 Harley FXE Superglide, '77 GL1000, '77 CB550k, '68 Suzuki K10 80, '68 Yamaha YR2, '69 BMW R69S, '71 Honda SL175, '02 Royal Enfield Bullet 500, '89 Yamaha FJ1200

Offline redrider736

  • Enthusiast
  • **
  • Posts: 168
Re: 79' 650 Cam removal
« Reply #6 on: July 08, 2014, 02:19:58 pm »
Quote from: redrider736 on July 08, 2014, 02:08:13 pm
Quote from: calj737 on July 08, 2014, 01:47:10 pm
Remove tappet covers, release all tension of rockers, remove rocker cover.

Locate cam sprocket. Screws on either edge need to removed, chain slipped off. You need to release tension from cam chain tensioner to create "slack" in the chain first (below carbs, nut on engine). Once chain is slacked, slip chain off, but tie it off from falling into engine. You may need to rotate crank to get to both bolts on sprocket.

Thanks calj737, just wasn't sure how to get "slack" on the chain..........


My have made a error on the tear down........  You mentioned  "release  all tension of rockers" prior  to removal of the rocker cover...  I didn't do that,  is that a concern?
Logged
78' CB550k (Not Run'n / Basket Case Project)
77/78 cool 2 member #269

Offline calj737

  • Really Old Timer ...
  • *******
  • Posts: 20,960
  • I refuse...
Re: 79' 650 Cam removal
« Reply #7 on: July 08, 2014, 02:22:27 pm »
It can be. On the 550/500 you need to do this to avoid damaging a valve that may be under compression at the moment. Not sure if the 650 rocker cover is the same in this respect. If you pulled it without hearing or feeling something "ugly" you're probably okay.
Logged
'74 550 Build http://forums.sohc4.net/index.php?topic=126401.0
'73 500 Build http://forums.sohc4.net/index.php?topic=132935.0

"Of all tyrannies, a tyranny sincerely exercised for the good of it's victim may be the most oppressive. It may be better to live under robber barons than under omnipotent moral busybodies. The robber baron's cruelty may sometimes sleep, his cupidity may at some point be satiated, but those who torment us for our own good will torment us without end for they do so with the approval of their own conscience." - C.S. Lewis

Offline redrider736

  • Enthusiast
  • **
  • Posts: 168
Re: 79' 650 Cam removal
« Reply #8 on: July 08, 2014, 02:29:41 pm »
Covers were barley on.....  For next time how do I release tension  ?
Logged
78' CB550k (Not Run'n / Basket Case Project)
77/78 cool 2 member #269

Offline Bankerdanny

  • Eventually I will be old enough in reality to be
  • Really Old Timer ...
  • *******
  • Posts: 7,617
  • Endeavor to persevere
Re: 79' 650 Cam removal
« Reply #9 on: July 08, 2014, 02:33:51 pm »
you loosen the screw adjusters. A 10MM (I think) wrench loosens the lock nuts, then a flat bladed screw driver to back the adjusters out will remove the tension. You can test first to see if you can move the rockers with your fingers, the ones you cannot you loosen manually.
Logged
"The problem with quotes on the Internet is that you never know if they're true" - Abraham Lincoln

Current: '76 CB750F. Previous:  '75 CB550F, 2007 Yamaha Vino 125 Scooter, '75 Harley FXE Superglide, '77 GL1000, '77 CB550k, '68 Suzuki K10 80, '68 Yamaha YR2, '69 BMW R69S, '71 Honda SL175, '02 Royal Enfield Bullet 500, '89 Yamaha FJ1200

Offline calj737

  • Really Old Timer ...
  • *******
  • Posts: 20,960
  • I refuse...
Re: 79' 650 Cam removal
« Reply #10 on: July 08, 2014, 02:35:51 pm »
Remove the tappet cover for each cylinder, both intake and exhaust. Look inside, and insert a blade screwdriver into the adjuster, but then use a 10mm box to loosen the adjuster all the way. This is the same technique for adjusting valves, only instead of tightening/loosening to a feeler gauge, you're taking all tension of the rocker and spring.
Logged
'74 550 Build http://forums.sohc4.net/index.php?topic=126401.0
'73 500 Build http://forums.sohc4.net/index.php?topic=132935.0

"Of all tyrannies, a tyranny sincerely exercised for the good of it's victim may be the most oppressive. It may be better to live under robber barons than under omnipotent moral busybodies. The robber baron's cruelty may sometimes sleep, his cupidity may at some point be satiated, but those who torment us for our own good will torment us without end for they do so with the approval of their own conscience." - C.S. Lewis

Offline cb650

  • Old Timer
  • ******
  • Posts: 3,864
Re: 79' 650 Cam removal
« Reply #11 on: July 08, 2014, 02:48:21 pm »
What are you going to do with the rest of the motor?  I might be interested in a couple items.
Logged
18 grand and 18 miles dont make you a biker

Offline redrider736

  • Enthusiast
  • **
  • Posts: 168
Re: 79' 650 Cam removal
« Reply #12 on: July 08, 2014, 02:54:17 pm »
Quote from: cb650 on July 08, 2014, 02:48:21 pm
What are you going to do with the rest of the motor?  I might be interested in a couple items.

I am planning to use the Cam and oil pan,  but everything  else  is up for grabs..
Logged
78' CB550k (Not Run'n / Basket Case Project)
77/78 cool 2 member #269

Offline redrider736

  • Enthusiast
  • **
  • Posts: 168
Re: 79' 650 Cam removal
« Reply #13 on: July 08, 2014, 03:01:45 pm »
Not sure what I am doing wrong but I can't seem to get any slack onto the Cam chain?

Logged
78' CB550k (Not Run'n / Basket Case Project)
77/78 cool 2 member #269

Offline redrider736

  • Enthusiast
  • **
  • Posts: 168
Re: 79' 650 Cam removal
« Reply #14 on: July 08, 2014, 03:09:51 pm »
Both Cam chain tension bolts are loose

Logged
78' CB550k (Not Run'n / Basket Case Project)
77/78 cool 2 member #269

Offline calj737

  • Really Old Timer ...
  • *******
  • Posts: 20,960
  • I refuse...
Re: 79' 650 Cam removal
« Reply #15 on: July 08, 2014, 03:42:27 pm »
Remove the left side, front cover (stator) and put a large socket on it, I believe 14mm. Rotate the crank a bit. The chain won't be super loose. You will also need to remove the 2 bolts on the sprocket mid way along the cam. That will allow you to slip the chain off the sprocket, sort of work it off and over to free the chain. Takes a bit of fiddling, but it will come free.

If nothing seems to work, take a Dremel or small cut-off tool and cut the cam chain, not near the sprocket or cam itself. Protect the debris from falling into the engine interior, and then remove the entire cam chain from the engine.
Logged
'74 550 Build http://forums.sohc4.net/index.php?topic=126401.0
'73 500 Build http://forums.sohc4.net/index.php?topic=132935.0

"Of all tyrannies, a tyranny sincerely exercised for the good of it's victim may be the most oppressive. It may be better to live under robber barons than under omnipotent moral busybodies. The robber baron's cruelty may sometimes sleep, his cupidity may at some point be satiated, but those who torment us for our own good will torment us without end for they do so with the approval of their own conscience." - C.S. Lewis

Offline redrider736

  • Enthusiast
  • **
  • Posts: 168
Re: 79' 650 Cam removal
« Reply #16 on: July 08, 2014, 04:31:27 pm »
Quote from: calj737 on July 08, 2014, 03:42:27 pm
Remove the left side, front cover (stator) and put a large socket on it, I believe 14mm. Rotate the crank a bit. The chain won't be super loose. You will also need to remove the 2 bolts on the sprocket mid way along the cam. That will allow you to slip the chain off the sprocket, sort of work it off and over to free the chain. Takes a bit of fiddling, but it will come free.

If nothing seems to work, take a Dremel or small cut-off tool and cut the cam chain, not near the sprocket or cam itself. Protect the debris from falling into the engine interior, and then remove the entire cam chain from the engine.

Thanks calj737! Success



Logged
78' CB550k (Not Run'n / Basket Case Project)
77/78 cool 2 member #269

Offline redrider736

  • Enthusiast
  • **
  • Posts: 168
Re: 79' 650 Cam removal
« Reply #17 on: July 08, 2014, 04:38:33 pm »
Quote from: Bankerdanny on July 08, 2014, 02:33:51 pm
you loosen the screw adjusters. A 10MM (I think) wrench loosens the lock nuts, then a flat bladed screw driver to back the adjusters out will remove the tension. You can test first to see if you can move the rockers with your fingers, the ones you cannot you loosen manually.

Thanks Bankerdanny,  I should have looked here first before "tearing" into her!
Logged
78' CB550k (Not Run'n / Basket Case Project)
77/78 cool 2 member #269

Offline calj737

  • Really Old Timer ...
  • *******
  • Posts: 20,960
  • I refuse...
Re: 79' 650 Cam removal
« Reply #18 on: July 08, 2014, 04:39:19 pm »
It had to be simple, if a simple-minded dolt like me could think of it  ;)
Logged
'74 550 Build http://forums.sohc4.net/index.php?topic=126401.0
'73 500 Build http://forums.sohc4.net/index.php?topic=132935.0

"Of all tyrannies, a tyranny sincerely exercised for the good of it's victim may be the most oppressive. It may be better to live under robber barons than under omnipotent moral busybodies. The robber baron's cruelty may sometimes sleep, his cupidity may at some point be satiated, but those who torment us for our own good will torment us without end for they do so with the approval of their own conscience." - C.S. Lewis

Offline MiGhost

  • What was that about being an
  • Hot Shot
  • ***
  • Posts: 362
Re: 79' 650 Cam removal
« Reply #19 on: July 08, 2014, 04:40:56 pm »
Quote from: redrider736 on July 08, 2014, 02:54:17 pm
Quote from: cb650 on July 08, 2014, 02:48:21 pm
What are you going to do with the rest of the motor?  I might be interested in a couple items.

I am planning to use the Cam and oil pan,  but everything  else  is up for grabs..

Make sure you keep the tach drive gear. You will need it.
The 500/550 tach drive gear is not compatible with the 650 cam.

You will also need a 650 tach. 
Logged
~ Ghost

Grey Ghost '80 CB650C: Updated Stock Restomod. Period Custom Cruiser (OEM harbags & trunk, Wixom Ranger fairing, Jardine turnouts)
Bad Moon '83 XJ750MK Midnight Maxim: Full Dress Tour Deluxe w/ X-1 Fairing

Offline redrider736

  • Enthusiast
  • **
  • Posts: 168
Re: 79' 650 Cam removal
« Reply #20 on: July 08, 2014, 05:00:22 pm »
Quote from: MiGhost on July 08, 2014, 04:40:56 pm
Quote from: redrider736 on July 08, 2014, 02:54:17 pm
Quote from: cb650 on July 08, 2014, 02:48:21 pm
What are you going to do with the rest of the motor?  I might be interested in a couple items.

I am planning to use the Cam and oil pan,  but everything  else  is up for grabs..

Make sure you keep the tach drive gear. You will need it.
The 500/550 tach drive gear is not compatible with the 650 cam.

You will also need a 650 tach.

Thanks ghost! Going to have to source a 650 Tach, the bike was missing it and a bunch of odds & ends
Logged
78' CB550k (Not Run'n / Basket Case Project)
77/78 cool 2 member #269

Offline goldarrow

  • one day, i'll be an
  • Old Timer
  • ******
  • Posts: 3,361
Re: 79' 650 Cam removal
« Reply #21 on: July 08, 2014, 05:28:58 pm »

Quote from: MiGhost on July 08, 2014, 04:40:56 pm
Quote from: redrider736 on July 08, 2014, 02:54:17 pm
Quote from: cb650 on July 08, 2014, 02:48:21 pm
What are you going to do with the rest of the motor?  I might be interested in a couple items.

I am planning to use the Cam and oil pan,  but everything  else  is up for grabs..

Make sure you keep the tach drive gear. You will need it.
The 500/550 tach drive gear is not compatible with the 650 cam.

You will also need a 650 tach.

Just cap the valves cover if you don't want to run tach
Logged
Life Is Full Of Challenges - And My Backyard Is Full Of SOHC4's

CB550 K0
CB750 K0, K2, K23 JDM, K45, K5
And the little ones z50r, xr50r, st90


750k5 http://forums.sohc4.net/index.php?topic=114817.0

Offline cb650

  • Old Timer
  • ******
  • Posts: 3,864
Re: 79' 650 Cam removal
« Reply #22 on: July 09, 2014, 06:07:08 am »
I'll trade u a tach for the starter cover and outer rocker covers.  if they are original 79.
Logged
18 grand and 18 miles dont make you a biker
Pages: [1]   Go Up
« previous next »