« previous next »
Pages: [1]   Go Down

Author Topic: PAMCO install question  (Read 1099 times)

0 Members and 1 Guest are viewing this topic.

Offline P.abrera

  • Hot Shot
  • ***
  • Posts: 404
PAMCO install question
« on: December 21, 2014, 06:36:37 AM »
Installed a Pamco kit on my 550 build. Not sure if I've got the trigger magnet position right. It's the one marked with the red dot, correct? Would appreciate some guidance from those who have done theirs. Thanks.
Logged

Offline goldarrow

  • one day, i'll be an
  • Old Timer
  • ******
  • Posts: 3,360
Re: PAMCO install question
« Reply #1 on: December 21, 2014, 07:25:56 AM »
That seems about right
Logged
Life Is Full Of Challenges - And My Backyard Is Full Of SOHC4's

CB550 K0
CB750 K0, K2, K23 JDM, K45, K5
And the little ones z50r, xr50r, st90


750k5 http://forums.sohc4.net/index.php?topic=114817.0

Offline P.abrera

  • Hot Shot
  • ***
  • Posts: 404
Re: PAMCO install question
« Reply #2 on: December 21, 2014, 04:36:52 PM »

Quote from: goldarrow on December 21, 2014, 07:25:56 AM
That seems about right

Cool, thanks


Sent from my iPhone using Tapatalk
Logged

Offline Gooseman

  • Full Member
  • *
  • Posts: 38
Re: PAMCO install question
« Reply #3 on: December 22, 2014, 07:50:26 AM »
Just installed one on a 750 this weekend, and from my understanding of the instruction that is the "correct" setup for the trigger magnets.

If you happened to install it in reverse you can just switch the coil connections. 
Logged

Offline PeWe

  • Really Old Timer ...
  • *******
  • Posts: 16,293
  • Bike almost back to the 70's 2015
Re: PAMCO install question
« Reply #4 on: December 22, 2014, 01:19:51 PM »
If the rotor is wrong, the engine will not run until you swap wiring between 1-4 vs 2-3 coils.
Logged
CB750 K6-76  970cc (Earlier 1005cc JMR Billet block on the shelf waiting for a comeback)
CB750 K2-75 Parts assembled to a stock K2

Updates of the CB750 K6 -1976
http://forums.sohc4.net/index.php/topic,180468.msg2092136.html#msg2092136
The billet block build thread
http://forums.sohc4.net/index.php/topic,49438.msg1863571.html#msg1863571
CB750 K2 -1975  build thread
http://forums.sohc4.net/index.php/topic,168243.msg1948381.html#msg1948381
K2 engine build thread. For a complete CB750 -75
http://forums.sohc4.net/index.php/topic,180088.msg2088008.html#msg2088008
Carb jetting, a long story Mikuni TMR32
http://forums.sohc4.net/index.php/topic,179479.msg2104967.html#msg2104967

Offline P.abrera

  • Hot Shot
  • ***
  • Posts: 404
Re: PAMCO install question
« Reply #5 on: December 22, 2014, 03:26:51 PM »
Got it, cheers gents. Happy holidays.


Sent from my iPhone using Tapatalk
Logged
Pages: [1]   Go Up
« previous next »