Author Topic: Looking for worn out RC engineering parts. (Read 3781 times)

gschuld · « **on:** April 07, 2013, 03:53:48 PM »

I know it's an odd request, but I'm looking for RC engineering parts that are too worn or damaged to re-use. Lightened alternators, cranks, rockers, cams, pistons, golden rods, super rods, big block, springs, retainers, ARD magnetos, whatever. I have a little research project going....

mildly damaged to totally destroyed welcome.

George

Bill/BentON Racing · « **Reply #1 on:** April 07, 2013, 04:59:28 PM »

Check your pms , was back in the cave, found something Jr. mighta stamped! Bill

gschuld · « **Reply #2 on:** April 07, 2013, 05:43:46 PM »

NICE

Thanks

gschuld · « **Reply #3 on:** July 01, 2013, 05:28:57 PM »

Bump

George

Retro Rocket · « **Reply #4 on:** July 29, 2013, 04:29:16 PM »

George, check your PM's mate...

AdrenalineReaper · « **Reply #5 on:** July 30, 2013, 07:45:39 PM »

Are you wanting to buy them, I have a rc points cover,scratched bad, and a distributor missing the drive gear

scottly · « **Reply #6 on:** July 30, 2013, 08:25:33 PM »

Quote from: AdrenalineReaper on July 30, 2013, 07:45:39 PM

Are you wanting to buy them, I have a rc points cover,scratched bad, and a distributor missing the drive gear

Good luck finding the drive gear, as they as they are as scarce as rocking-horse #$%*...

Medyo Bastos · « **Reply #7 on:** July 31, 2013, 05:07:45 AM »

george i have a cam sprocket, not slotted, but drilled

gschuld · « **Reply #8 on:** August 01, 2013, 03:51:44 PM »

PMs sent!

George

BLUE71TURBO · « **Reply #9 on:** August 01, 2013, 07:02:00 PM »

Quote from: AdrenalineReaper on July 30, 2013, 07:45:39 PM

Are you wanting to buy them, I have a rc points cover,scratched bad, and a distributor missing the drive gear

If you are talking about the gear at the bottom of the distributor, it is a stock Mallory part from their VW distributor. A special note.... The distributors used in the RC Engineering angle drive run in reverse rotation. That means the points cam and advance mechanism are reversed. So you can't use any VW designed distrbutor or magneto in the RC Engineering angle drive setup unless it is setup for the reverse rotation.

gschuld · « **Reply #10 on:** April 29, 2015, 05:51:56 PM »

Just bumping this back up, it's been a while, but I'm still interested in dead or alive RC stuff.

George

NalleyRacing · « **Reply #11 on:** April 30, 2015, 03:07:23 AM »

Talk with Mike Rieck. He has four of my heads and the unusable one had RC anodized retainers and was even stamped RC ENG on the bottom if I recall correctly.Along with the name STEAKLEY and BOB etched on the bottom.. I also have a 71mm block done by RC with the stock "736cc" stamp removed and replaced with just the number 1000. It has the standard copper O-ring's and a small corner of the block was shaved to accommodate the plate for the Hilborn fuel pump drive.

gschuld · « **Reply #12 on:** April 30, 2015, 04:17:22 AM »

Trey, I sent you an e-mail

George

Big Jay · « **Reply #13 on:** April 30, 2015, 11:41:24 PM »

Got a couple of fueler cylinder heads...... Oh wait, we are going to be using them again

gschuld · « **Reply #14 on:** May 01, 2015, 02:11:31 PM »

Not nice Jay ...not nice.

...

And what happened to all the take out parts from those heads?

George

Big Jay · « **Reply #15 on:** May 01, 2015, 05:40:45 PM »

Talk about parts? They will be getting the same parts we used in the triple heads.

gschuld · « **Reply #16 on:** May 01, 2015, 05:49:31 PM »

That's great. I was just asking about whether the parts coming out for good were getting saved or tossed.

George

jkbarberie · « **Reply #17 on:** May 01, 2015, 08:03:20 PM »

I have a non working RC engineering electronic ignition. I also have a duplex chain and sprocket set but I don't know if they are from RC engineering.

Jeff

Big Jay · « **Reply #18 on:** May 01, 2015, 11:41:57 PM »

Quote from: gschuld on May 01, 2015, 05:49:31 PM

That's great. I was just asking about whether the parts coming out for good were getting saved or tossed.

George

Never gave it any thought. I will run it past Russ.

Bill/BentON Racing · « **Reply #19 on:** May 02, 2015, 01:42:25 AM »

There's money in them parts! Awesome history, great memento's and gifts. Bill

gschuld · « **Reply #20 on:** May 02, 2015, 03:27:59 AM »

Quote from: Big Jay on May 01, 2015, 11:41:57 PM

Quote from: gschuld on May 01, 2015, 05:49:31 PM
That's great. I was just asking about whether the parts coming out for good were getting saved or tossed.

George
Never gave it any thought. I will run it past Russ.

Jay,

yes please do. I'm pretty sure Russ would want to keep the take out parts

jkbarbarie,

Pm sent. Thanks

George

Big Jay · « **Reply #21 on:** May 04, 2015, 10:10:43 PM »

You sure you want this stuff? It probably has Russ Collins DNA on it?

gschuld · « **Reply #22 on:** May 04, 2015, 10:18:39 PM »

If Russ Jr doesn't want it, than yes, I do. Not sure I want any DNA though

George

News:

Author Topic: Looking for worn out RC engineering parts. (Read 3781 times)