« previous next »
Pages: [1]   Go Down

Author Topic: Carb t-fitting oring size??  (Read 1664 times)

0 Members and 1 Guest are viewing this topic.

Offline Dannodarko

  • Full Member
  • *
  • Posts: 89
Carb t-fitting oring size??
« on: June 27, 2015, 06:14:07 AM »
Good morning all!!! So as my topic states, I need the oring size for the t fitting between the carbs, I FINALLY got it running last night and fuel is leaking out of them thanks so much in advance!! Here's a pic of what I'm looking for
Logged

Offline 01Thomas

  • Hot Shot
  • ***
  • Posts: 475
Re: Carb t-fitting oring size??
« Reply #1 on: June 27, 2015, 01:40:37 PM »
HI
The parts manual says 7.8 x 1.9  but I think 8 x 2 mm will work just fine - and will be easier to find.

regards
Thomas
Logged
1971 Honda CB750 Four K1 [Engine: CB750E-1113521 / Frame: CB750-1113838]
1977 Seeley Honda CB750F (F1) [Engine: CB750E-2551214 / Frame No: SH7-655F]

'96 Yamaha YZF750SP & '81 Moto Guzzi SP1000 & '80 Moto Guzzi 850 LeMans II & '82 Bimota KB-3 [Frame No 49] & '66 Ducati 50 SL/1 & '53 Miele K-50 & '38 Miele 98

DH

  • Guest
Re: Carb t-fitting oring size??
« Reply #2 on: June 28, 2015, 07:50:44 PM »
If you're near a John Deere equipment dealer, ask for part #T77814 o-ring. 8 of 'em.
Logged

Offline riverfever

  • Master
  • *****
  • Posts: 1,796
Re: Carb t-fitting oring size??
« Reply #3 on: June 28, 2015, 08:34:45 PM »
I got something close enough at a local mom and pop hardware store.
Logged
http://forums.sohc4.net/index.php?topic=127186.0

"You wouldn't think that out here...a man could simply run clear...out of country but oh my...oh my...nothing but the light." -Ben Nichols

Offline Dannodarko

  • Full Member
  • *
  • Posts: 89
Re: Carb t-fitting oring size??
« Reply #4 on: June 29, 2015, 11:47:38 AM »
Awesome thanks guys!!!
Logged

Offline Rmart

  • Full Member
  • *
  • Posts: 12
Re: Carb t-fitting oring size??
« Reply #5 on: July 05, 2015, 08:25:14 PM »
Don't get just a type of black O-ring if possible get the green ones that are designed for AC they are oil and gas resistant I got a green set of O-rings for the AC systems at Harbor freight and there are about 10 of the overhangs in there in one of a compartments are the right size and it only cost me about two or three dollars
Rj
Logged

Offline Dannodarko

  • Full Member
  • *
  • Posts: 89
Re: Carb t-fitting oring size??
« Reply #6 on: July 06, 2015, 03:38:00 AM »
Good to know!!! Thanks!!!!!!
Logged

Offline FGKouki

  • Full Member
  • *
  • Posts: 57
Re: Carb t-fitting oring size??
« Reply #7 on: July 06, 2015, 01:09:10 PM »
I had good luck at Napa- forget the size though- 7mm x 2 maybe?  Just take the carbs with ya! 
Logged
Pages: [1]   Go Up
« previous next »