« previous next »
Pages: [1]   Go Down

Author Topic: New or reused head studs and nuts?  (Read 466 times)

0 Members and 1 Guest are viewing this topic.

Offline cj8990

  • Full Member
  • *
  • Posts: 56
New or reused head studs and nuts?
« on: June 22, 2016, 03:35:36 PM »
Should I reuse my old head studs or order some new ones?

Also on one of them the whole stud came out and not just the nut during disassembly.. if I do reuse am I fine to just put the whole stud in and torque to spec or should I remove the nut (its on there pretty good) and torque the stud in and then the nut?

-Corey
Logged

Offline MickB

  • Expert
  • ****
  • Posts: 945
Re: New or reused head studs and nuts?
« Reply #1 on: June 22, 2016, 03:36:34 PM »
Reuse them, as long as they're in good nick.
Logged

Offline cj8990

  • Full Member
  • *
  • Posts: 56
Re: New or reused head studs and nuts?
« Reply #2 on: June 22, 2016, 03:46:17 PM »
Cool.. as for retorqueing the one stud that came out then I should probably get the nut off.. torque stud to 8 lb and then during reassembly torque the nut down?
Logged

Offline madmtnmotors

  • When did I get to be a
  • Really Old Timer ...
  • *******
  • Posts: 6,110
  • Sunny Central Florida
Re: New or reused head studs and nuts?
« Reply #3 on: June 22, 2016, 05:40:25 PM »
Quote from: cj8990 on June 22, 2016, 03:46:17 PM
Cool.. as for retorqueing the one stud that came out then I should probably get the nut off.. torque stud to 8 lb and then during reassembly torque the nut down?

Yes.
Logged
TAMTF...


Wilbur



Projects:
"Evolution": http://forums.sohc4.net/index.php?topic=100352.0
"P.O. Debacle": http://forums.sohc4.net/index.php/topic,126692.msg1441661.html#msg1441661
F2/F3 O-rings: http://forums.sohc4.net/index.php?topic=113672.msg1300721#msg1300721
Cam Tower Studs: https://www.mcmaster.com/#93210a017/=t19sgp
Clean up that nasty harness: http://forums.sohc4.net/index.php?topic=137351.msg1549191#msg1549191
http://forums.sohc4.net/index.php/topic,148188.msg1688494.html#msg1688494
http://forums.sohc4.net/index.php/topic,139544.msg1579364.html#msg1579364
                                          
Charging system diagnosis: http://forums.sohc4.net/index.php?topic=1012.msg8345#msg8345
Get the manuals: http://manuals.sohc4.net/cb750k/
The Dragon: http://forums.sohc4.net/index.php?topic=45183.msg1571675#msg1571675
Headlight Switch: http://forums.sohc4.net/index.php?topic=113986.msg1283236#msg1283236
Branden's leak free top end thread: http://forums.sohc4.net/index.php?topic=107040.0
Engine Lifting Made Easy: http://forums.sohc4.net/index.php/topic,58210.msg1684742.html#msg1684742
                                      http://forums.sohc4.net/index.php/topic,100352.msg1675840.html#msg1675840
Static and Dynamic Timing: http://www.hondachopper.com/garage/carb_info/timing/timing1.html
Airbox Gasket Replacement: http://forums.sohc4.net/index.php/topic,114485.msg1290000.html#msg1290000
"Café" : http://forums.sohc4.net/index.php/topic,84697.msg953814.html#msg953814
PD Carb Choke Linkage: http://forums.sohc4.net/index.php/topic,100352.msg1669248.html#msg1669248
                                    http://forums.sohc4.net/index.php/topic,110931.msg1248354.html#msg1248354
                                    http://forums.sohc4.net/index.php/topic,48858.msg515204.html#msg515204
Follow up on your damn posts: http://forums.sohc4.net/index.php/topic,144305.msg1791605.html#msg1791605
Taiwanese Cam Chain Tensioners:  http://forums.sohc4.net/index.php/topic,155043.msg1774841.html#msg1774841
Gumtwo Seat Cover: http://forums.sohc4.net/index.php/topic,164440.msg1897366.html#msg1897366
Primary Drive: http://forums.sohc4.net/index.php/topic,166063.msg1919278.html#msg1919278
Tank Latch: http://forums.sohc4.net/index.php/topic,165975.msg1919495.html#msg1919495
Shorten your forks: http://vintage-and-classic-honda-s.456789.n3.nabble.com/How-to-shorten-forks-td4042465.html DO NOT CUT THE SPRINGS!
Clutch How To: http://vintage-and-classic-honda-s.456789.n3.nabble.com/How-to-change-and-adjust-a-clutch-SOHC-td4040391.html
Late model K7/K8/F2/F3 front sprocket cover removal: http://forums.sohc4.net/index.php/topic,178428.msg2072279.html#msg2072279
630 to 530 conversion: http://forums.sohc4.net/index.php/topic,180710.msg2094423.html#msg2094423

Sent from my Tandy TRS-80!

Offline ksmith0034

  • When I grow up I want to be a
  • Hot Shot
  • ***
  • Posts: 616
    • Please subscribe to my motovlog
Re: New or reused head studs and nuts?
« Reply #4 on: June 22, 2016, 07:29:59 PM »
Why take the chance?  Just buy new ones and be don't worry about them.  Buy APE studs if you REALLY want to be sure they're secure!
Logged
It took 10 years but she's finally done!
             ↓   ↓   ↓   ↓   ↓
Stocker 2 Rocker CAFE conversion

My YouTube channel HERE:
https://www.youtube.com/MotoCafeRacer
Pages: [1]   Go Up
« previous next »