Author Topic: CB750 K8 Build  (Read 11770 times)

0 Members and 1 Guest are viewing this topic.

Offline firebane

  • Hot Shot
  • ***
  • Posts: 360
CB750 K8 Build
« on: August 01, 2016, 01:10:32 PM »
I thought I had started a thread on this but I can't seem to find it so I figure I'll start it now.

I bought this bike in November of 2015 and was hoping to get it on the road in a timely fashion but unfortunately between work and life its been taking a bit longer than normal. In the time I have owned it it has gone through a lot of updates and been cleaned up a lot.

It is still a work in progress and recently I discovered that the swing arm was lengthened by at least 3-3.5" so that is the current battle in the bike.

Day 1 of bike being home:


Cut the frame and pulled the valve cover as this thing was being held on by gobs of orange rtv and was leaking everywhere. Also discovered a few tappet nuts were missing and fixed that all up.


Pulled off the ugly exhaust that the bike came with (I have a 4-1 replacing this now)


Pulled the stock bars and put some renthal ultra lows on


Not sure what the purpose of this was but it really makes the back of this bike look horrible


Discovered with the help of some awesome forum members the swing was extended by 3-3.5" and following this found everything related to the rear brake drum setup was also extended. With this extra 3-3.5" of extension putting this bike onto its center stand was a living miserable of a suck job to the point I hurt my back the first time.


New wiring harness attached and needing tidied up.


Swing arm yanked out and cut that atrocious weld job off the back of the bike


Current state of bike.. Front forks have been cleaned and painted black removing the horrible blue (fork dust covers to be installed later). Hoping once I replace the swing arm and all hardware that I will then continue on with the wiring and getting the bike running. At this point I'm not expecting this to happen till probably spring and be able to ride for next season.
« Last Edit: October 23, 2016, 06:58:24 PM by firebane »

Offline madmtnmotors

  • When did I get to be a
  • Really Old Timer ...
  • *******
  • Posts: 6,090
  • Sunny Central Florida
Re: CB750 K8 Build
« Reply #1 on: August 01, 2016, 01:54:04 PM »
With this extra 3-3.5" of extension putting this bike onto its center stand was a living miserable of a suck job to the point I hurt my back the first time.

That pretty much describes putting a stock CB750 on the centerstand as well! The motion to lift it onto the centerstand is somewhat unnatural. I will face the side of the bike, left hand on the handle bar, right hand on the grab rail or under the seat, just behind the upper shock mount. I then place the ball of my left foot on the centerstand lever. Most of the force is applied downward with my left foot with some lifting force with my right hand and a little pulling force with my left hand.  8)
TAMTF...


Wilbur



Projects:
"Evolution": http://forums.sohc4.net/index.php?topic=100352.0
"P.O. Debacle": http://forums.sohc4.net/index.php/topic,126692.msg1441661.html#msg1441661
F2/F3 O-rings: http://forums.sohc4.net/index.php?topic=113672.msg1300721#msg1300721
Cam Tower Studs: https://www.mcmaster.com/#93210a017/=t19sgp
Clean up that nasty harness: http://forums.sohc4.net/index.php?topic=137351.msg1549191#msg1549191
http://forums.sohc4.net/index.php/topic,148188.msg1688494.html#msg1688494
http://forums.sohc4.net/index.php/topic,139544.msg1579364.html#msg1579364
                                          
Charging system diagnosis: http://forums.sohc4.net/index.php?topic=1012.msg8345#msg8345
Get the manuals: http://manuals.sohc4.net/cb750k/
The Dragon: http://forums.sohc4.net/index.php?topic=45183.msg1571675#msg1571675
Headlight Switch: http://forums.sohc4.net/index.php?topic=113986.msg1283236#msg1283236
Branden's leak free top end thread: http://forums.sohc4.net/index.php?topic=107040.0
Engine Lifting Made Easy: http://forums.sohc4.net/index.php/topic,58210.msg1684742.html#msg1684742
                                      http://forums.sohc4.net/index.php/topic,100352.msg1675840.html#msg1675840
Static and Dynamic Timing: http://www.hondachopper.com/garage/carb_info/timing/timing1.html
Airbox Gasket Replacement: http://forums.sohc4.net/index.php/topic,114485.msg1290000.html#msg1290000
"Café" : http://forums.sohc4.net/index.php/topic,84697.msg953814.html#msg953814
PD Carb Choke Linkage: http://forums.sohc4.net/index.php/topic,100352.msg1669248.html#msg1669248
                                    http://forums.sohc4.net/index.php/topic,110931.msg1248354.html#msg1248354
                                    http://forums.sohc4.net/index.php/topic,48858.msg515204.html#msg515204
Follow up on your damn posts: http://forums.sohc4.net/index.php/topic,144305.msg1791605.html#msg1791605
Taiwanese Cam Chain Tensioners:  http://forums.sohc4.net/index.php/topic,155043.msg1774841.html#msg1774841
Gumtwo Seat Cover: http://forums.sohc4.net/index.php/topic,164440.msg1897366.html#msg1897366
Primary Drive: http://forums.sohc4.net/index.php/topic,166063.msg1919278.html#msg1919278
Tank Latch: http://forums.sohc4.net/index.php/topic,165975.msg1919495.html#msg1919495
Shorten your forks: http://vintage-and-classic-honda-s.456789.n3.nabble.com/How-to-shorten-forks-td4042465.html DO NOT CUT THE SPRINGS!
Clutch How To: http://vintage-and-classic-honda-s.456789.n3.nabble.com/How-to-change-and-adjust-a-clutch-SOHC-td4040391.html
Late model K7/K8/F2/F3 front sprocket cover removal: http://forums.sohc4.net/index.php/topic,178428.msg2072279.html#msg2072279
630 to 530 conversion: http://forums.sohc4.net/index.php/topic,180710.msg2094423.html#msg2094423

Sent from my Tandy TRS-80!

Offline SOHC4 Cafe Racer Fan

  • Speak up, Whipper-Snapper! I'm a
  • Really Old Timer ...
  • *******
  • Posts: 15,731
  • SOHC/4 Member #1235
Re: CB750 K8 Build
« Reply #2 on: August 01, 2016, 01:55:27 PM »
That swingarm looked all kinds of wrong.  Even if dragging is your goal, THAT is not the way to do it.
I'm glad to hear you are rectifying the errors of the PO.
1975 CB550K1 "Blue" Stockish Restomod (http://forums.sohc4.net/index.php?topic=135005.0)
1975 CB550F1 frame/CB650 engine hybrid "The Hot Mess" (http://forums.sohc4.net/index.php/topic,150220.0.html)
2008 Triumph Thruxton (http://forums.sohc4.net/index.php/topic,190956.0.html)
2014 MV Agusta Brutale Dragster 800
2015 Yamaha FZ-09 (http://forums.sohc4.net/index.php/topic,186861.0.html)

"There are some things nobody needs in this world, and a bright-red, hunch-back, warp-speed 900cc cafe racer is one of them — but I want one anyway, and on some days I actually believe I need one.... Being shot out of a cannon will always be better than being squeezed out of a tube. That is why God made fast motorcycles, Bubba." Hunter S. Thompson, Song of the Sausage Creature, Cycle World, March 1995.  (http://www.latexnet.org/~csmith/sausage.html and https://magazine.cycleworld.com/article/1995/3/1/song-of-the-sausage-creature)

Sold/Emeritus
1973 CB750K2 "Bionic Mongrel" (http://forums.sohc4.net/index.php?topic=132734.0) - Sold
1977 CB750K7 "Nine Lives" Restomod (http://forums.sohc4.net/index.php?topic=50490.0) - Sold
2005 RVT1000RR RC51-SP2 "El Diablo" - Sold
2016+ Triumph Thruxton 1200 R (http://forums.sohc4.net/index.php/topic,170198.0.html) - Sold

Offline firebane

  • Hot Shot
  • ***
  • Posts: 360
Re: CB750 K8 Build
« Reply #3 on: August 01, 2016, 01:57:41 PM »
That swingarm looked all kinds of wrong.  Even if dragging is your goal, THAT is not the way to do it.
I'm glad to hear you are rectifying the errors of the PO.

Its difficult finding these bikes in good shape anymore and I'm pretty finicky and like things to be right. Even if I chose to sell this bike right now I would feel all sorts of wrong knowing I sold a bike with sketchy parts on it.

So the hunt right now is on for a new swing arm and either another frame to repair this one or I'm going to just rebuild the back end of this thing.

Offline Desert-SOHC

  • Expert
  • ****
  • Posts: 1,015
  • It's old
Re: CB750 K8 Build
« Reply #4 on: August 01, 2016, 09:22:04 PM »
That pretty much describes putting a stock CB750 on the centerstand as well! The motion to lift it onto the centerstand is somewhat unnatural. I will face the side of the bike, left hand on the handle bar, right hand on the grab rail or under the seat, just behind the upper shock mount. I then place the ball of my left foot on the centerstand lever. Most of the force is applied downward with my left foot with some lifting force with my right hand and a little pulling force with my left hand.  8)

Mine is lowered and I roll the rear tire up on a 2x4 and a 1x4....takes no effort.
90 F350 Lariat CS S/C Dually
90 S&S 11SC Cabover Camper
97 FLHTP (under construction)
11 Ranger S/C 2wd

Offline Retro Rocket

  • Eggs are hard due too a
  • Really Old Timer ...
  • *******
  • Posts: 19,279
  • ROCK & ROLL
Re: CB750 K8 Build
« Reply #5 on: August 01, 2016, 10:01:04 PM »
Make sure you get a K7/K8 swingarm to replace that one, they are wider on the left hand side than the early K models {10mm} .... ;)
750 K2 1000cc
750 F1 970cc
750 Bitsa 900cc
If You can't fix it with a hammer, You've got an electrical problem.

Offline calj737

  • Really Old Timer ...
  • *******
  • Posts: 21,018
  • I refuse...
Re: CB750 K8 Build
« Reply #6 on: August 02, 2016, 01:55:38 AM »
Send a PM to Bill Benton, likely he will have a good quality spare swing arm.
'74 550 Build http://forums.sohc4.net/index.php?topic=126401.0
'73 500 Build http://forums.sohc4.net/index.php?topic=132935.0

"Of all tyrannies, a tyranny sincerely exercised for the good of it's victim may be the most oppressive. It may be better to live under robber barons than under omnipotent moral busybodies. The robber baron's cruelty may sometimes sleep, his cupidity may at some point be satiated, but those who torment us for our own good will torment us without end for they do so with the approval of their own conscience." - C.S. Lewis

Offline firebane

  • Hot Shot
  • ***
  • Posts: 360
Re: CB750 K8 Build
« Reply #7 on: August 02, 2016, 04:46:13 AM »
Found a swing arm on ebay for $50 shipped to my door and have bronze bushings on the way too.

I know the bolt on the drum side for the brake stay is shouldered, but is the head of that bolt special? I have looked around and it looks like a normal bolt

Offline Retro Rocket

  • Eggs are hard due too a
  • Really Old Timer ...
  • *******
  • Posts: 19,279
  • ROCK & ROLL
Re: CB750 K8 Build
« Reply #8 on: August 02, 2016, 06:33:38 PM »
Found a swing arm on ebay for $50 shipped to my door and have bronze bushings on the way too.

I know the bolt on the drum side for the brake stay is shouldered, but is the head of that bolt special? I have looked around and it looks like a normal bolt

You should ask here first mate, you'll probably be able to get everything you need from the forum, and at a very reasonable price... ;)
Was the swingarm you bought specifically a K7/K8 arm ...?
750 K2 1000cc
750 F1 970cc
750 Bitsa 900cc
If You can't fix it with a hammer, You've got an electrical problem.

Offline firebane

  • Hot Shot
  • ***
  • Posts: 360
Re: CB750 K8 Build
« Reply #9 on: August 02, 2016, 07:01:24 PM »
Found a swing arm on ebay for $50 shipped to my door and have bronze bushings on the way too.

I know the bolt on the drum side for the brake stay is shouldered, but is the head of that bolt special? I have looked around and it looks like a normal bolt

You should ask here first mate, you'll probably be able to get everything you need from the forum, and at a very reasonable price... ;)
Was the swingarm you bought specifically a K7/K8 arm ...?

It is specific. Issue is that I'm Canadian so shipping plus exchange rate generally kills me. So finding one for $50 shipped on Ebay was a great price. I asked someone on here and they quoted me a great price for the arm but $60 for shipping.

Offline Retro Rocket

  • Eggs are hard due too a
  • Really Old Timer ...
  • *******
  • Posts: 19,279
  • ROCK & ROLL
Re: CB750 K8 Build
« Reply #10 on: August 03, 2016, 01:03:01 AM »
Found a swing arm on ebay for $50 shipped to my door and have bronze bushings on the way too.

I know the bolt on the drum side for the brake stay is shouldered, but is the head of that bolt special? I have looked around and it looks like a normal bolt

You should ask here first mate, you'll probably be able to get everything you need from the forum, and at a very reasonable price... ;)
Was the swingarm you bought specifically a K7/K8 arm ...?

It is specific. Issue is that I'm Canadian so shipping plus exchange rate generally kills me. So finding one for $50 shipped on Ebay was a great price. I asked someone on here and they quoted me a great price for the arm but $60 for shipping.

Cool, good result... ;)
750 K2 1000cc
750 F1 970cc
750 Bitsa 900cc
If You can't fix it with a hammer, You've got an electrical problem.

Offline firebane

  • Hot Shot
  • ***
  • Posts: 360
Re: CB750 K8 Build
« Reply #11 on: September 04, 2016, 03:30:04 PM »
So I've had some time lately and was able to get that swing arm from ebay. The final measurement of extension is exactly 3" longer over stock!!

Swingarm that came with the bike is on the left and the proper one is on the right:


Showing the difference in length between the two

Offline firebane

  • Hot Shot
  • ***
  • Posts: 360
Re: CB750 K8 Build
« Reply #12 on: September 29, 2016, 04:52:06 PM »
So here is the next conundrum in my story. I recently picked up a hoop to tie up the back end of my bike that required hacking off a lot of crap from the previous owner. Unfortunately in doing this you really find out how bad things are and now I'm at a point where I have to decide what I want to do.

My first choice is to weld the hoop on and put some new plate over both sides to tie everything together. My second choice is completely getting rid of the shock stud and all applicable metal and either installing something like cognito motos shock stud kit (https://cognitomoto.com/products/shock-mounting-kit) or coming up with my own means.

Here are some pics of just the left side as I haven't started on the right till I decide what I want to do or where I go. I will also be the first to admit I may have cut out a bit more than needed on this side and if I do the right side I have a better idea of how to do things.








Offline calj737

  • Really Old Timer ...
  • *******
  • Posts: 21,018
  • I refuse...
Re: CB750 K8 Build
« Reply #13 on: September 29, 2016, 06:04:50 PM »
Cut the stock gusset off clean to the triangular brace, weld in a new plate with a stud inserted, weld on your new hoop and tie everything in together. I'd encourage you to weld a slug into the existing frame and slip your hoop over it. Leave a 1/16" gape between your hoop and the frame, and weld it up tight. Stronger and cleaner.
'74 550 Build http://forums.sohc4.net/index.php?topic=126401.0
'73 500 Build http://forums.sohc4.net/index.php?topic=132935.0

"Of all tyrannies, a tyranny sincerely exercised for the good of it's victim may be the most oppressive. It may be better to live under robber barons than under omnipotent moral busybodies. The robber baron's cruelty may sometimes sleep, his cupidity may at some point be satiated, but those who torment us for our own good will torment us without end for they do so with the approval of their own conscience." - C.S. Lewis

Offline firebane

  • Hot Shot
  • ***
  • Posts: 360
Re: CB750 K8 Build
« Reply #14 on: September 29, 2016, 06:20:04 PM »
Cut the stock gusset off clean to the triangular brace, weld in a new plate with a stud inserted, weld on your new hoop and tie everything in together. I'd encourage you to weld a slug into the existing frame and slip your hoop over it. Leave a 1/16" gape between your hoop and the frame, and weld it up tight. Stronger and cleaner.

You share my thoughts. But that then leaves one concern.... When I put in a new stud how does one know where to place it so it's as close to stick as possible? I have seen drawings showing measurements but most of the references to help me are gone on the bike.

Maybe I will seek help with another post asking for references

Offline calj737

  • Really Old Timer ...
  • *******
  • Posts: 21,018
  • I refuse...
Re: CB750 K8 Build
« Reply #15 on: September 29, 2016, 08:00:00 PM »
Just measure the location of the stock unit before cutting it off. Even if your new stud is off by 1/4", it won't matter. Being in the proper plane relative to the swing arm shock mount does matter.
'74 550 Build http://forums.sohc4.net/index.php?topic=126401.0
'73 500 Build http://forums.sohc4.net/index.php?topic=132935.0

"Of all tyrannies, a tyranny sincerely exercised for the good of it's victim may be the most oppressive. It may be better to live under robber barons than under omnipotent moral busybodies. The robber baron's cruelty may sometimes sleep, his cupidity may at some point be satiated, but those who torment us for our own good will torment us without end for they do so with the approval of their own conscience." - C.S. Lewis

Offline 70CB750

  • Labor omnia vincit improbus.
  • Really Old Timer ...
  • *******
  • Posts: 14,792
  • Northern Virginia
Re: CB750 K8 Build
« Reply #16 on: September 30, 2016, 05:38:45 AM »
Following

Offline firebane

  • Hot Shot
  • ***
  • Posts: 360
Re: CB750 K8 Build
« Reply #17 on: October 01, 2016, 01:39:43 PM »
Stage 1... Complete. Offending metal is gone. Thanks to harisluv I got the hoop and slugs put in but not yet welded yet. Also in place is the new and proper swing arm that isn't extended by 3".  I took an original seat pan and now found out well its far too long so a custom seat will be play now lol! I now have a cb750f complete seat, cb750k pan and a seat from a unknown bike.

Next up will be getting some metal and redoing shock mounts and I'm sure that will be fun.
 
« Last Edit: October 01, 2016, 01:41:35 PM by firebane »

Offline firebane

  • Hot Shot
  • ***
  • Posts: 360
Re: CB750 K8 Build
« Reply #18 on: October 23, 2016, 04:41:30 PM »
So figure it was time to add some updates since I've had some time to work on the bike again. I have figured out a secure method of reattaching the shocks to the frame and it seems that it should work well. Here are some pics of the progress.

What you see is a piece of 5/8 rod which is the diameter of the shock bushing hole, a few collars, and some bushings. I don't have access to high end equipment so all of this is being done with a grinder with a grinding wheel and a cut off wheel with a small 110v welder.

I haven't decided how I want to secure the shock yet... I'm debating one of two means. First means is drilling the center of the rod and using either a m6 or m8 socket cap bolt with washer or use the 5/8 rod and thread it for a flanged acorn nut... thoughts? I also realize the right shock is leaning WAY out. I'm verifying side to side by placing a square on the rod being lifted by the jack and squaring from that to the side of the shock.

I am also taking feedback if you guys think the left shock can be brought in just a tad or if perhaps where it mounts to the frame needs to be moved back a bit. Once I have everything figured out to secure the shock I will be getting some 14g or 16g steel to make a plate for welding to the frame and putting the sleeve inside to hold everything snug.

Side profile:


3/4 Rear View:


Underside View:


Rear View:


Offline calj737

  • Really Old Timer ...
  • *******
  • Posts: 21,018
  • I refuse...
Re: CB750 K8 Build
« Reply #19 on: October 24, 2016, 05:03:46 AM »
Your shocks should be plumb from bottom to top. A forward lean angle is fine, but they can't be splayed outward as you have them.

Thread the end of the rod and secure it with a proper nut. As for the 14-16ga steel as a mounting plate, thats way too thin and weak. 1/4" minimum. I appreciate that a 110v welder won't weld that up straight away, but you have a couple of choices: have someone else weld that aspect of the frame properly, OR, if you can't then-

Use some 3/8" plate. Bevel the outside and inside edge so the portion in contact with the frame is about 1/8". Then weld a single thin pass on the outside, and again on the inside. Then repeat with a "cover pass". The 1/8" contact portion is a "landing area" and the bevel allows you to get enough weld in with appropriate penetration to fuse the gusset to the frame.

Shock mounts take significant stress. This is NOT a place to DIY and wing-it. Got to be safe, and strong.
'74 550 Build http://forums.sohc4.net/index.php?topic=126401.0
'73 500 Build http://forums.sohc4.net/index.php?topic=132935.0

"Of all tyrannies, a tyranny sincerely exercised for the good of it's victim may be the most oppressive. It may be better to live under robber barons than under omnipotent moral busybodies. The robber baron's cruelty may sometimes sleep, his cupidity may at some point be satiated, but those who torment us for our own good will torment us without end for they do so with the approval of their own conscience." - C.S. Lewis

Offline firebane

  • Hot Shot
  • ***
  • Posts: 360
Re: CB750 K8 Build
« Reply #20 on: October 24, 2016, 05:43:41 AM »
I appreciate the feed back but the original steel for shock mounts is about 14g.. maybe closer to 13g but I don't have a great piece to test off of. The piece I did have came in around 0.06xx inches. I realize you can go thicker but putting 1/2 inch of steel on the back is crazy.

My plan is to use either 14g or 16g and fold it over like the original piece and then weld that to the bike.

I know about the shocks I wrote about that above lol.

Offline calj737

  • Really Old Timer ...
  • *******
  • Posts: 21,018
  • I refuse...
Re: CB750 K8 Build
« Reply #21 on: October 24, 2016, 11:02:30 AM »
What is "crazy" is trying to shortcut on structurally important aspects of a vehicle that your life depends upon with a 110v welder. If you rent. Competent and experienced welder, then you should leave those modifications and repairtls to someone who is.

Your choices of materials are completely wrong and that's an indication that your lack of experience calls out for good advice. But it's your bike and your neck. I hope you're safe and that shoukd you ever have a failure that neither you nor anyone around you is injured.

Owning a welding machine and knowing how to operate it doesn't make you a welder or fabricator. It just makes you handy and dangerous.
'74 550 Build http://forums.sohc4.net/index.php?topic=126401.0
'73 500 Build http://forums.sohc4.net/index.php?topic=132935.0

"Of all tyrannies, a tyranny sincerely exercised for the good of it's victim may be the most oppressive. It may be better to live under robber barons than under omnipotent moral busybodies. The robber baron's cruelty may sometimes sleep, his cupidity may at some point be satiated, but those who torment us for our own good will torment us without end for they do so with the approval of their own conscience." - C.S. Lewis

Offline firebane

  • Hot Shot
  • ***
  • Posts: 360
Re: CB750 K8 Build
« Reply #22 on: October 24, 2016, 11:20:22 AM »
What is "crazy" is trying to shortcut on structurally important aspects of a vehicle that your life depends upon with a 110v welder. If you rent. Competent and experienced welder, then you should leave those modifications and repairtls to someone who is.

Your choices of materials are completely wrong and that's an indication that your lack of experience calls out for good advice. But it's your bike and your neck. I hope you're safe and that shoukd you ever have a failure that neither you nor anyone around you is injured.

Owning a welding machine and knowing how to operate it doesn't make you a welder or fabricator. It just makes you handy and dangerous.

I never said I was going to do the final welding on this as I know my limitations. I can do everything up to that part and ensure its welded correctly and properly.

I'm not sure how your saying my choice of materials is wrong? I'm using the exact same materials that the original pieces were made of so I'm not sure why you are making that assumption?

Offline 540nova

  • Hot Shot
  • ***
  • Posts: 593
Re: CB750 K8 Build
« Reply #23 on: October 24, 2016, 11:50:27 AM »
Personally, I would have left the stock mounts, and worked around it.


Sent from my iPhone using Tapatalk

Offline slikwilli420

  • Master of Disaster
  • Master
  • *****
  • Posts: 2,362
Re: CB750 K8 Build
« Reply #24 on: October 24, 2016, 11:59:40 AM »
Interested to see where this goes as I may have to redo some shock mounts. The stock material is sheet metal and is pretty substantial. I usually agree with Cal, but I cannot see how using 1/4" plate would be even remotely necessary. Many bikes over the years have used sheet metal in that gauge range for shock and motor/swingarm mounts. Its all in the prep and actual welding.
All you gotta do is do what you gotta do.

Vintage Speed Parts Mashup: http://forums.sohc4.net/index.php?topic=133638.0
Rickman CR Parts Kit Refresh: http://forums.sohc4.net/index.php/topic,154837.0.html
AHRMA CB750 Racer: http://forums.sohc4.net/index.php/topic,158461.0.html
AHRMA Superbike Heavyweight Racer: http://forums.sohc4.net/index.php/topic,173120.0.html
'76F CB750 Patina Redemption: http://forums.sohc4.net/index.php/topic,174871.0.html