Author Topic: Cb400f "goldie", Handbuilt show, Bikeexif, and dyno run. (Read 79296 times)

innovativems · « **Reply #550 on:** July 30, 2017, 06:11:36 AM »

Quote from: calj737 on July 30, 2017, 03:56:49 AM

You might want to give your exhaust a quick but thorough wipe down with Acetone too before you for a lengthy ride. It will clean the grease and oils off before they burn in as tarnished marks on the stainless.

Good call cal! Completely forgot that in all the excitement of it running.

Sent from my iPhone using Tapatalk

seanbarney41 · « **Reply #551 on:** July 30, 2017, 08:23:09 AM »

Quote from: innovativems on July 30, 2017, 06:11:00 AM

Quote from: seanbarney41 on July 30, 2017, 03:17:26 AM
come on man...the rest of the bike is so good...but you have to do something about an inner rear fender and some real air filters
Those are K&n filters on the bike.

Yep fenders are coming along. Tanner matic is doing a carbon front and I'm going to swap the number plate and build a inner rear out of carbon. Probably be a month before that's all done

Sent from my iPhone using Tapatalk

thank goodness! Not sure why I doubted you as this bike exceeds expectations every where else. Can't wait to see the Tannnermatic fender. Amazingly, I have not seen anyone else use his stuff on this site. Guessing those are the biggest K&Ns that fit the 400 carbs. I feel spoiled by the parts availability of the cb750. I forget what its like trying to find good stuff for other bikes

innovativems · « **Reply #552 on:** July 30, 2017, 05:14:54 PM »

No kidding these smaller fours get alittle hard at times. Thank goodness for ttr400 for most of the parts

Sent from my iPhone using Tapatalk

innovativems · « **Reply #553 on:** July 30, 2017, 05:20:25 PM »

Well shake down went pretty good. Gota get some plug chops in. Hesitates around 6k but once through it she's scoots. Also got one float that is hanging up I'm gonna have to deal with. She is getting there.

Sent from my iPhone using Tapatalk

SOHC4 Cafe Racer Fan · « **Reply #554 on:** July 30, 2017, 09:23:48 PM »

Looking good, out there in the wild!

innovativems · « **Reply #555 on:** July 31, 2017, 05:54:02 AM »

Thank you sir!

SOHC4 Cafe Racer Fan · « **Reply #556 on:** August 01, 2017, 09:01:22 AM »

Congratulations! Your CB400f has been nominated for Bike of the Month September 2017. Please post that you "accept" the nomination in the BOTM thread: http://forums.sohc4.net/index.php/topic,167520.0.html

rickmoore24 · « **Reply #557 on:** August 01, 2017, 09:49:10 AM »

Well deserved!!

Stev-o · « **Reply #558 on:** August 01, 2017, 03:03:03 PM »

Looking good!

innovativems · « **Reply #559 on:** August 03, 2017, 06:24:12 AM »

thank you everyone! Your comments mean alot!

innovativems · « **Reply #560 on:** August 13, 2017, 04:02:34 PM »

Been slow to post updates. Got the bodywork all cut and buffed out. And made a battery hold down. My Tanner matic carbon front fender arrives this week and then I'll make my carbon number plate and rear hugger.

Sent from my iPhone using Tapatalk

innovativems · « **Reply #561 on:** August 14, 2017, 07:52:45 PM »

Put a few more miles on tonight breaking her in

Sent from my iPhone using Tapatalk

scunny · « **Reply #562 on:** August 15, 2017, 12:39:35 AM »

looking good

innovativems · « **Reply #563 on:** August 15, 2017, 05:39:55 AM »

Quote from: scunny on August 15, 2017, 12:39:35 AM

looking good

Thank you!

RAFster122s · « **Reply #564 on:** August 15, 2017, 03:01:03 PM »

Very nice...so do we get to see these new doodads?

innovativems · « **Reply #565 on:** August 16, 2017, 05:18:04 AM »

Quote from: RAF122S on August 15, 2017, 03:01:03 PM

Very nice...so do we get to see these new doodads?

Just got this today. Once I get the fender I'll get some sheet carbon to make the front number plate. Once those are on I'll determine the plan for a rear hugger. Part of me really likes it being open. But a hugger would be nice to have

Sent from my iPhone using Tapatalk

innovativems · « **Reply #566 on:** August 16, 2017, 05:18:26 AM »

Sent from my iPhone using Tapatalk

riverfever · « **Reply #567 on:** August 16, 2017, 08:17:17 AM »

I'm sprung.

SOHC4 Cafe Racer Fan · « **Reply #568 on:** August 16, 2017, 08:36:44 AM »

Hot damn.

innovativems · « **Reply #569 on:** August 19, 2017, 01:25:37 PM »

Alright got my fender. I'm going to get some carbon and make a front number plate. My question is on a rear hugger. Do I;
1-not run one
2-do carbon fiber
3-polished aluminum

I like it all open but the sensible side of me says I should run one.

Sent from my iPhone using Tapatalk

innovativems · « **Reply #570 on:** August 19, 2017, 02:06:02 PM »

Kind of leaning towards painting the fender to match, leave the number plate and either go polished aluminum hugger or no hugger

Sent from my iPhone using Tapatalk

seanbarney41 · « **Reply #571 on:** August 19, 2017, 02:48:16 PM »

You gotta do something to keep crap of your air filters and the back of the engine...not doing something just send the message that this bike will not really be used, and that's not a good look no matter how clean it is.

innovativems · « **Reply #572 on:** August 19, 2017, 02:55:27 PM »

Agreed. Leaning towards polished hugger and painting the fender

Sent from my iPhone using Tapatalk

SOHC4 Cafe Racer Fan · « **Reply #573 on:** August 19, 2017, 04:46:21 PM »

Carbon hugger. Subtle but enough to keep the dirt and water off your motor, carbs, electronics - and it'll look good and match your front.

innovativems · « **Reply #574 on:** August 23, 2017, 04:09:52 AM »

Put a few more miles on the 400. Going to change the oil this weekend. Got some aluminum coming and some carbon to see which looks right for the hugger

Sent from my iPhone using Tapatalk

News:

Author Topic: Cb400f "goldie", Handbuilt show, Bikeexif, and dyno run. (Read 79296 times)