Author Topic: Cb400f "goldie", Handbuilt show, Bikeexif, and dyno run. (Read 79336 times)

innovativems · « **Reply #325 on:** March 08, 2017, 05:12:03 PM »

Triples are going on tomorrow and I'll begin work to mount my led headlight.

Oh ya a piece of art arrived today. My stage 2 ported head from the man, the myth, the legend, MRieck

Sent from my iPhone using Tapatalk

calj737 · « **Reply #326 on:** March 08, 2017, 05:33:05 PM »

Only Stage 2?

Skimper!

MRieck · « **Reply #327 on:** March 08, 2017, 05:52:23 PM »

The 400 ports are fairly big for a small engine....they just need to be massaged a bit Cal.

Camrector · « **Reply #328 on:** March 08, 2017, 08:53:34 PM »

Beautiful as always and Mikes handwriting is getting better too!

innovativems · « **Reply #329 on:** March 08, 2017, 10:16:35 PM »

Head is on and torqued down!

Sent from my iPhone using Tapatalk

grcamna2 · « **Reply #330 on:** March 08, 2017, 10:25:47 PM »

Looking good

calj737 · « **Reply #331 on:** March 09, 2017, 04:21:12 AM »

Quote from: MRieck on March 08, 2017, 05:52:23 PM

The 400 ports are fairly big for a small engine....they just need to be massaged a bit Cal.

You can't pay for kid's college Mike, just massaging ports...

innovativems · « **Reply #332 on:** March 09, 2017, 04:54:11 AM »

Quote from: calj737 on March 09, 2017, 04:21:12 AM

Quote from: MRieck on March 08, 2017, 05:52:23 PM
The 400 ports are fairly big for a small engine....they just need to be massaged a bit Cal.
You can't pay for kid's college Mike, just massaging ports...

I can't pay for my kids college if I hang around here too much. Too much bad influence to buy goodies on here

Sent from my iPhone using Tapatalk

MRieck · « **Reply #333 on:** March 09, 2017, 05:28:56 AM »

Quote from: calj737 on March 09, 2017, 04:21:12 AM

Quote from: MRieck on March 08, 2017, 05:52:23 PM
The 400 ports are fairly big for a small engine....they just need to be massaged a bit Cal.
You can't pay for kid's college Mike, just massaging ports...

....but I thought a massage always results in a happy ending Cal. Now I'm confused.

calj737 · « **Reply #334 on:** March 09, 2017, 07:40:45 AM »

Quote from: MRieck on March 09, 2017, 05:28:56 AM

....but I thought a massage always results in a happy ending Cal. Now I'm confused.

Now we know where you spend your nights and weekends... at the nearby Asian Massage Parlor.

palepainter · « **Reply #335 on:** March 09, 2017, 09:36:35 PM »

Man...That sure is purty. Nice work Shawn.

innovativems · « **Reply #336 on:** March 09, 2017, 10:04:40 PM »

Quote from: palepainter on March 09, 2017, 09:36:35 PM

Man...That sure is purty. Nice work Shawn.

Thanks!!

Sent from my iPhone using Tapatalk

innovativems · « **Reply #337 on:** March 09, 2017, 10:06:37 PM »

Got alot done tonight. Polished my triples and upper fork legs. And mounted them with tapered bearings. Also got the tank and tail into primer.

Sent from my iPhone using Tapatalk

innovativems · « **Reply #338 on:** March 10, 2017, 09:05:19 PM »

Blocked the tank and tail. Blocked out very nice. Going to do one more round of primer and then ready for paint in a week.

Sent from my iPhone using Tapatalk

palepainter · « **Reply #339 on:** March 11, 2017, 03:10:14 PM »

Wax on. Wax off.

Sent from my iPhone using Tapatalk

innovativems · « **Reply #340 on:** March 14, 2017, 09:51:11 AM »

Last round of primer is going on tonight. Picked up the last of powdercoat parts. Also got the clutch side togther. Went with ebc clutch fibers and Barnett HD springs.

Sent from my iPhone using Tapatalk

innovativems · « **Reply #341 on:** March 14, 2017, 09:43:38 PM »

Front end is mocked up. Gold valves will be here this week and I'll get the forks back together. Also last round of primer.

Sent from my iPhone using Tapatalk

grcamna2 · « **Reply #342 on:** March 14, 2017, 10:06:52 PM »

That looks good;I love that oil cooler !

calj737 · « **Reply #343 on:** March 15, 2017, 04:27:52 AM »

I'd check for clearance around the oil cooler with the exhaust installed... just to be sure.

innovativems · « **Reply #344 on:** March 15, 2017, 07:22:37 AM »

Quote from: grcamna2 on March 14, 2017, 10:06:52 PM

That looks good;I love that oil cooler !

Thanks!

innovativems · « **Reply #345 on:** March 15, 2017, 07:41:27 AM »

Quote from: calj737 on March 15, 2017, 04:27:52 AM

I'd check for clearance around the oil cooler with the exhaust installed... just to be sure.

With the jacks in the way, I've eye balled it and it's looking good. Should have the forks finished by the weekend and i can get the jacks out from under the frame. From the pictures Kevin sent me, I'll be set for clearance with about any system with his cooler setup.

innovativems · « **Reply #346 on:** March 15, 2017, 07:09:07 PM »

Got my preload adjusters from ttr400. Wet sanding primer Friday and planning to paint Monday.

Sent from my iPhone using Tapatalk

grcamna2 · « **Reply #347 on:** March 15, 2017, 07:27:21 PM »

I like those ttr400 preload adjusters

They fit the stock 33mm fork tubes,yes ?

palepainter · « **Reply #348 on:** March 15, 2017, 07:28:58 PM »

Oh...The preload adjusters are the business..... Tell us more about them.

SOHC4 Cafe Racer Fan · « **Reply #349 on:** March 15, 2017, 08:03:41 PM »

Quote from: grcamna2 on March 15, 2017, 07:27:21 PM

I like those ttr400 preload adjusters They fit the stock 33mm fork tubes,yes ?

35 mm

News:

Author Topic: Cb400f "goldie", Handbuilt show, Bikeexif, and dyno run. (Read 79336 times)