Author Topic: Cb400f "goldie", Handbuilt show, Bikeexif, and dyno run. (Read 79331 times)

SOHC4 Cafe Racer Fan · « **Reply #375 on:** March 22, 2017, 08:31:01 AM »

Quote from: calj737 on March 22, 2017, 03:31:27 AM

Quote from: 540nova on March 22, 2017, 03:29:48 AM
This bike is crying out for Black anodized GSX-R forks

Everyone has an opinion. I agree with Cal about the black GSXR forks though.

innovativems · « **Reply #376 on:** March 22, 2017, 12:52:06 PM »

haha, no usd forks on this ole girl. my 74 h2 on the other hand may get some. still kicking around what i'm going to do with that. that one is up after i get the cb350f done.

SOHC4 Cafe Racer Fan · « **Reply #377 on:** March 22, 2017, 12:55:41 PM »

Quote from: innovativems on March 22, 2017, 12:52:06 PM

haha, no usd forks on this ole girl. my 74 h2 on the other hand may get some. still kicking around what i'm going to do with that. that one is up after i get the cb350f done.

Ok. I'll compromise. Conventional R6 forks!

innovativems · « **Reply #378 on:** March 24, 2017, 07:41:30 PM »

Well gold valves for my forks finally arrived after being ordered almost 3 months. And my adapters aren't in the order. Ignore the little things in life.

Threw on my header and collector quick. Gonna move my oil cooler mount to give me a little more clearance. Also gonna start figuring out how I'm going to bend the back of the collector so the can clears the swingarm.

Sent from my iPhone using Tapatalk

grcamna2 · « **Reply #379 on:** March 24, 2017, 08:35:33 PM »

Those rear shocks 'Rock'

calj737 · « **Reply #380 on:** March 25, 2017, 02:25:15 AM »

Ac couple of pie cuts before the foot peg, create just enough angle to kick the can out.

Or, add a length of straight tubing to extend the megaphone mouth beyond the swing arm, tilting it up via the extension.

Or, a rigid mount attached to the backside of the megaphone that pushes the can outward.

540nova · « **Reply #381 on:** March 25, 2017, 03:23:44 AM »

Quote from: calj737 on March 25, 2017, 02:25:15 AM

Ac couple of pie cuts before the foot peg, create just enough angle to kick the can out.

+1

The hole in the hoop by your rearset is conveniently located for a clamp mount, but you probably already figured that out

This bike looks way cooler than I thought it would. Great paint! Still hoping for a GSX-R fork transplant. It deserves it.

Sent from my iPhone using Tapatalk

innovativems · « **Reply #382 on:** March 25, 2017, 08:55:27 PM »

Quote from: calj737 on March 25, 2017, 02:25:15 AM

Ac couple of pie cuts before the foot peg, create just enough angle to kick the can out.

Or, add a length of straight tubing to extend the megaphone mouth beyond the swing arm, tilting it up via the extension.

Or, a rigid mount attached to the backside of the megaphone that pushes the can outward.

Thanks cal! If my exhaust doesn't sell soon so I can get the mc-again system I'm going to start doing pie cuts to get me where I need to be.

Sent from my iPhone using Tapatalk

innovativems · « **Reply #383 on:** March 25, 2017, 09:00:18 PM »

Quote from: 540nova on March 25, 2017, 03:23:44 AM

Quote from: calj737 on March 25, 2017, 02:25:15 AM
Ac couple of pie cuts before the foot peg, create just enough angle to kick the can out.

+1

The hole in the hoop by your rearset is conveniently located for a clamp mount, but you probably already figured that out

This bike looks way cooler than I thought it would. Great paint! Still hoping for a GSX-R fork transplant. It deserves it.

Sent from my iPhone using Tapatalk

Haha on the hoop.

Thank you! I'm excited for how it's coming along. Turning out better then what I had in my mind. No zuki forks!! Honda Honda Honda!

Sent from my iPhone using Tapatalk

innovativems · « **Reply #384 on:** March 25, 2017, 09:01:11 PM »

Alright im finally going to mount my headlight and number plate this weekendish

Sent from my iPhone using Tapatalk

Bootsey · « **Reply #385 on:** March 26, 2017, 03:19:26 AM »

What's the MC-again system? The delkevic looks pretty darn good from here!

palepainter · « **Reply #386 on:** March 26, 2017, 07:43:21 AM »

Lookikng great Shawn. Whats the scoop on the headlight? Hi-Lo? Wattage?

innovativems · « **Reply #387 on:** March 27, 2017, 07:10:03 AM »

Quote from: Bootsey on March 26, 2017, 03:19:26 AM

What's the MC-again system? The delkevic looks pretty darn good from here!

The mc-again system has hand bent head pipes and give me alot of clearance with the swingarm. I do like the look of the delkevic but am open to not having to cut up the collector.

innovativems · « **Reply #388 on:** March 27, 2017, 07:13:06 AM »

Quote from: palepainter on March 26, 2017, 07:43:21 AM

Lookikng great Shawn. Whats the scoop on the headlight? Hi-Lo? Wattage?

Thanks Mike!

The light is fully adjustable and comes with a dimmer switch, so can go to low output all the way up to full. 2000 lumens on this bad boy! Crazy bright!

503400f · « **Reply #389 on:** March 27, 2017, 04:35:14 PM »

What size wheel and tire setups did you go with? LOVING the gold.

innovativems · « **Reply #390 on:** March 27, 2017, 09:27:04 PM »

Quote from: 503400f on March 27, 2017, 04:35:14 PM

What size wheel and tire setups did you go with? LOVING the gold.

Did 90 on the front with a wm2 wheel and 110 and wm3 on the back

Sent from my iPhone using Tapatalk

innovativems · « **Reply #391 on:** March 27, 2017, 09:28:59 PM »

Need some input on front number plate. I'm struggling with the angle of it. I'm started to think I mount it flush against the forks and cut out around the clip ons and gauge and then bend some aluminum to go over those areas.

Sent from my iPhone using Tapatalk

SOHC4 Cafe Racer Fan · « **Reply #392 on:** March 27, 2017, 11:58:29 PM »

I vote for cutting out relief spots for the clip-ons, so it can sit flush. It looks "off" canted forward.

catsoup · « **Reply #393 on:** March 28, 2017, 05:46:05 AM »

is the headlight going behind the number plate? i think flush is the better angle, but there will be a lot of holes, no?

innovativems · « **Reply #394 on:** March 28, 2017, 07:10:04 AM »

The light will poke through alittle bit. Only that hole and if I do cuts around the clip ons I'm planning to bend some aluminum to go over that area and either rivet it of weld it to the number plate

Sent from my iPhone using Tapatalk

innovativems · « **Reply #395 on:** March 28, 2017, 03:04:49 PM »

The more I think about it, the more I think I'm going to glass my own number plate.

Sent from my iPhone using Tapatalk

grcamna2 · « **Reply #396 on:** March 28, 2017, 03:17:21 PM »

Quote from: innovativems on March 28, 2017, 03:04:49 PM

The more I think about it, the more I think I'm going to glass my own number plate.

Sent from my iPhone using Tapatalk

How about an alloy one ?

innovativems · « **Reply #397 on:** March 28, 2017, 03:40:35 PM »

Quote from: grcamna2 on March 28, 2017, 03:17:21 PM

Quote from: innovativems on March 28, 2017, 03:04:49 PM
The more I think about it, the more I think I'm going to glass my own number plate.

Sent from my iPhone using Tapatalk

How about an alloy one ?

That's what I was gonna run but with the shapes to go around the clip ons and my gauge I could glass it quick and paint it to match. Might do a small glass fender too

Sent from my iPhone using Tapatalk

innovativems · « **Reply #398 on:** March 29, 2017, 11:16:02 PM »

Finally got everything for my forks. Race tech gold valves and springs with ttr400 preload adjusters are in.

Sent from my iPhone using Tapatalk

grcamna2 · « **Reply #399 on:** March 30, 2017, 02:38:49 AM »

That's going to handle Great

News:

Author Topic: Cb400f "goldie", Handbuilt show, Bikeexif, and dyno run. (Read 79331 times)