« previous next »
Pages: 1 2 3 [4]   Go Down

Author Topic: This is my first CB750F  (Read 14499 times)

0 Members and 4 Guests are viewing this topic.

Offline Johnny340

  • Hot Shot
  • ***
  • Posts: 431
Re: This is my first CB750F
« Reply #75 on: March 13, 2018, 10:55:05 AM »
Quote from: calj737 on March 13, 2018, 04:32:34 AM
Johnny - Is your tank bare metal inside? If so, you might try this product Master Series Silver. Another member, Pete was so damn adamant about it, I gave it a go. Its a moisture cured "primer" that you dump in, tumble once or twice, pour out. Let stand for 2-3 days, voila, done. Ethanol and gas resistant, and super thin, and no other chemicals. I'm impressed with it.

Yes the tank is bare inside.  It looked really good so I used Metal Rescue in case there was any surface rust I couldn't see and I rinsed it out, then sprayed Dry Coat. I don't know if something happened while it got dipped at the hydro graphic place but there were black flecks in it.  It is clean again and I have an inline filter as well.  I may try that stuff in the link.
I'd like to get it running perfect if possible now that the black flecks are taken care of.  I thought that raising the needles was going to do it but it still hangs before idling down.  The air screws have some affect on this (1/2T out is better than 1& 1/2T out).  I have one size up on the Pilots already at 45.  It's almost behaving like there is an air leak..  Any thoughts? 
CX3 cam with 251 duration should idle without hanging, eh?
Logged
1975 CB750F0 Super Sport
1972 CB750K2
1981 CB650
1974 T-500
2003 GSXR750
2006 YZ250

Offline calj737

  • Really Old Timer ...
  • *******
  • Posts: 21,070
  • I refuse...
Re: This is my first CB750F
« Reply #76 on: March 13, 2018, 12:23:40 PM »
Quote from: SOHC4 Cafe Racer Fan on March 13, 2018, 08:19:44 AM
Quote from: calj737 on March 13, 2018, 04:32:34 AM
Johnny - Is your tank bare metal inside? If so, you might try this product Master Series Silver. Another member, Pete was so damn adamant about it, I gave it a go. Its a moisture cured "primer" that you dump in, tumble once or twice, pour out. Let stand for 2-3 days, voila, done. Ethanol and gas resistant, and super thin, and no other chemicals. I'm impressed with it.

Hey, Cal.  Are you referring to the Primer/Sealer Silver product: https://shop.masterseriesct.com/product.sc;jsessionid=E94EE496B956F91F16821D32D396CC33.p3plqscsfapp006?productId=6&categoryId=1 ?
It looks like a pint would be sufficient for a gas tank.  Probably a lot thinner coat than Caswell epoxy.
Yep. And it is thiner and more workable than Caswell. Jury is still out on durability, but I've used it on some stuff in the shop I fab'ed up from steel and so far is working out well. Applied it with a foam brush on those steel surfaces.
Logged
'74 550 Build http://forums.sohc4.net/index.php?topic=126401.0
'73 500 Build http://forums.sohc4.net/index.php?topic=132935.0

"Of all tyrannies, a tyranny sincerely exercised for the good of it's victim may be the most oppressive. It may be better to live under robber barons than under omnipotent moral busybodies. The robber baron's cruelty may sometimes sleep, his cupidity may at some point be satiated, but those who torment us for our own good will torment us without end for they do so with the approval of their own conscience." - C.S. Lewis

Offline SOHC4 Cafe Racer Fan

  • Speak up, Whipper-Snapper! I'm a
  • Really Old Timer ...
  • *******
  • Posts: 15,733
  • SOHC/4 Member #1235
Re: This is my first CB750F
« Reply #77 on: March 13, 2018, 12:38:04 PM »
Quote from: calj737 on March 13, 2018, 12:23:40 PM
Quote from: SOHC4 Cafe Racer Fan on March 13, 2018, 08:19:44 AM
Quote from: calj737 on March 13, 2018, 04:32:34 AM
Johnny - Is your tank bare metal inside? If so, you might try this product Master Series Silver. Another member, Pete was so damn adamant about it, I gave it a go. Its a moisture cured "primer" that you dump in, tumble once or twice, pour out. Let stand for 2-3 days, voila, done. Ethanol and gas resistant, and super thin, and no other chemicals. I'm impressed with it.

Hey, Cal.  Are you referring to the Primer/Sealer Silver product: https://shop.masterseriesct.com/product.sc;jsessionid=E94EE496B956F91F16821D32D396CC33.p3plqscsfapp006?productId=6&categoryId=1 ?
It looks like a pint would be sufficient for a gas tank.  Probably a lot thinner coat than Caswell epoxy.
Yep. And it is thiner and more workable than Caswell. Jury is still out on durability, but I've used it on some stuff in the shop I fab'ed up from steel and so far is working out well. Applied it with a foam brush on those steel surfaces.

Good to know.  Fortunately, my next tank is aluminum so I should not need to coat it.
Logged
1975 CB550K1 "Blue" Stockish Restomod (http://forums.sohc4.net/index.php?topic=135005.0)
1975 CB550F1 frame/CB650 engine hybrid "The Hot Mess" (http://forums.sohc4.net/index.php/topic,150220.0.html)
2008 Triumph Thruxton (http://forums.sohc4.net/index.php/topic,190956.0.html)
2014 MV Agusta Brutale Dragster 800
2015 Yamaha FZ-09 (http://forums.sohc4.net/index.php/topic,186861.0.html)

"There are some things nobody needs in this world, and a bright-red, hunch-back, warp-speed 900cc cafe racer is one of them — but I want one anyway, and on some days I actually believe I need one.... Being shot out of a cannon will always be better than being squeezed out of a tube. That is why God made fast motorcycles, Bubba." Hunter S. Thompson, Song of the Sausage Creature, Cycle World, March 1995.  (http://www.latexnet.org/~csmith/sausage.html and https://magazine.cycleworld.com/article/1995/3/1/song-of-the-sausage-creature)

Sold/Emeritus
1973 CB750K2 "Bionic Mongrel" (http://forums.sohc4.net/index.php?topic=132734.0) - Sold
1977 CB750K7 "Nine Lives" Restomod (http://forums.sohc4.net/index.php?topic=50490.0) - Sold
2005 RVT1000RR RC51-SP2 "El Diablo" - Sold
2016+ Triumph Thruxton 1200 R (http://forums.sohc4.net/index.php/topic,170198.0.html) - Sold

Offline Johnny340

  • Hot Shot
  • ***
  • Posts: 431
Re: This is my first CB750F
« Reply #78 on: March 13, 2018, 03:56:47 PM »
Fixed the neutral switch.  :)

Runs best with Air Screws at only 1/4 turn out which leads me to believe the Pilots are still too small.  It idles great there but still has a hang up at 2300RPM for a couple seconds before idling down.  Any suggestions? Thx.

Another pic.
Logged
1975 CB750F0 Super Sport
1972 CB750K2
1981 CB650
1974 T-500
2003 GSXR750
2006 YZ250

Offline Johnny340

  • Hot Shot
  • ***
  • Posts: 431
Re: This is my first CB750F
« Reply #79 on: October 02, 2018, 12:08:20 PM »
Fixed Idle and it runs perfect now! New Fox shocks.  Finished!  Super fun to ride!!


Logged
1975 CB750F0 Super Sport
1972 CB750K2
1981 CB650
1974 T-500
2003 GSXR750
2006 YZ250

Offline Johnny340

  • Hot Shot
  • ***
  • Posts: 431
Re: This is my first CB750F
« Reply #80 on: October 02, 2018, 12:26:41 PM »
More pics
Logged
1975 CB750F0 Super Sport
1972 CB750K2
1981 CB650
1974 T-500
2003 GSXR750
2006 YZ250

Offline 754

  • Really Old Timer ...
  • *******
  • Posts: 29,058
Re: This is my first CB750F
« Reply #81 on: October 02, 2018, 01:38:19 PM »
 Great looking bike  look me up if you get up this way..
 One thing I would do if it's were mine,
 I would make headlight bracket lo get and curl the front down to at least midpoint of damper. If you did not use countersunk Allen head to mount light block, that can get it lower.
 Or just paint the damper black, make it blend in, right now it stands out.l
 Enjoy the bike.,
Logged
Maker of the WELDLESS 750 Frame Kit
dodogas99@gmail.com
Kelowna B.C.       Canada

My next bike will be a ..ANFOB.....

It's All part of the ADVENTURE...

73 836cc.. Green, had it for 3 decades!!
Lost quite a few CB 750's along the way

Offline Johnny340

  • Hot Shot
  • ***
  • Posts: 431
Re: This is my first CB750F
« Reply #82 on: October 04, 2018, 08:24:46 PM »
Thanks a lot Frank!  You bet I will when I'm in town.
I know what  you mean about the steering dampener.  I have the headlight as low as possible and it just barely clears the dampener as it is.  I tried it lower but it would have had to stick out front too far to clear it..  You're right, I'll paint the dampener black so it doesn't stand out and that should improve the look of the front end.

It's super fun to ride, but Summer ended too fast!
« Last Edit: October 04, 2018, 08:26:52 PM by Johnny340 »
Logged
1975 CB750F0 Super Sport
1972 CB750K2
1981 CB650
1974 T-500
2003 GSXR750
2006 YZ250

Offline Johnny340

  • Hot Shot
  • ***
  • Posts: 431
Re: This is my first CB750F
« Reply #83 on: October 17, 2018, 09:07:10 AM »
I just wanted to say a big THANK YOU too all of the forum members who helped me out!  I would never have been this happy with it without all of the help.  What a great forum!  You know who you are but these ones pop into my head: 754, Calj737, Flybox1, Bodi, Hondaman, Scottly, TwoTired, PeWe, godffery, Mystic1. Thank you to you and all the others who helped or even just offered an opinion along the way.
Logged
1975 CB750F0 Super Sport
1972 CB750K2
1981 CB650
1974 T-500
2003 GSXR750
2006 YZ250

Offline diep

  • Full Member
  • *
  • Posts: 1
Re: This is my first CB750F
« Reply #84 on: December 09, 2018, 08:15:40 PM »
love the work you did on your bike, its beautiful. where did you get the seat and seat pan?
Logged

Offline Johnny340

  • Hot Shot
  • ***
  • Posts: 431
Re: This is my first CB750F
« Reply #85 on: December 09, 2018, 09:39:38 PM »
Quote from: diep on December 09, 2018, 08:15:40 PM
love the work you did on your bike, its beautiful. where did you get the seat and seat pan?

Thanks for your comments!  I had the seat custom made from a friend in the upholstery business and the seat pan came from here:
https://www.dimecitycycles.com/legendary-motorcycles-fiberglass-thruxton-cafe-racer-motorcycle-seat-pan.html
Logged
1975 CB750F0 Super Sport
1972 CB750K2
1981 CB650
1974 T-500
2003 GSXR750
2006 YZ250
Pages: 1 2 3 [4]   Go Up
« previous next »