Author Topic: Project B7 Underway! Billet Big Block Built By Bill BentON Racing (Read 62017 times)

dragracer · « **Reply #75 on:** October 31, 2017, 11:38:23 PM »

Quote from: Bill/BentON Racing on October 31, 2017, 04:01:39 PM

Sure thing shorty! Lol. Progress the B plate number the other day was the metal one. The B friction also not available but I have sources......

Yep, that's me. Always short a dollar or a much needed part. Just rub it in my friend. Lol. I'll make something happen with the project bike before 2017 is over. It'll be good to move into 2018 with something to work from versus starting from scratch. I'm going to stay fairly local in 2018. Make as many Commerce races as possible so my brother can compete in the bike class. The rest of the time I'll spend racing my drag car in nearby bracket races. I'll run a very limited Man Cup schedule. Likely just the first, and last race of 2018.😶

Bill/BentON Racing · « **Reply #76 on:** November 01, 2017, 04:13:05 AM »

I hear you.....hope to make Commerce more often for sure, Jimmy Heisler needs some challengers, lol!

Bill/BentON Racing · « **Reply #77 on:** November 07, 2017, 07:21:44 PM »

Back up bike coming along.

bleach8484 · « **Reply #78 on:** November 07, 2017, 09:02:00 PM »

Looking good Bill!

What kind of Marshall amp was that hanging out back there?

dragracer · « **Reply #79 on:** November 08, 2017, 02:23:22 AM »

Quote from: Bill/BentON Racing on November 07, 2017, 07:21:44 PM

Back up bike coming along.

So fresh and so clean. Lol. Nice work Bill. Hope you won't have to race the back up and will be on the primary instead. I'm still accessing my status on racing my SOHC but I will enter a bike in street ET regardless. Either the old KZ or the ZX10 will be in the trailer.

voodooracer · « **Reply #80 on:** November 08, 2017, 07:42:20 AM »

Nice build, Bill. After you set some records, pop that thang in that laydown frame and let's go fast! hehe. I'll look for yall at the ManCup on the 18th.

Bill/BentON Racing · « **Reply #81 on:** November 08, 2017, 05:06:44 PM »

November 2018 the lay down turbo should be ready.....at least I hope so. Billet block engine waiting on primary drive rt now....but I'm busy with the back up and primary ride. Installed Dyna S and EK DRZ2 530 drive chain today. 17/48 gearing, might not need 5th, we'll see. Keeping it so I can back all original one day. Has some improvements like ignition, coils, drive chain and sprockets, SS allen heads etc.Even if primary bike ready I'll probably ride this in S ET. We'll see how TestnTune goes. My new pitbike...Yamaha 1961 YDT-1, 250cc 2 stroke 1 carb, Y manifold. Elec start, the Patina Queen Rat Bike!

rickmoore24 · « **Reply #82 on:** November 08, 2017, 11:06:38 PM »

I like the safety wire on the key.

Bill/BentON Racing · « **Reply #83 on:** November 14, 2017, 11:14:37 AM »

Clutch time and f and r brakes, we done, cept for tuning

Bill/BentON Racing · « **Reply #84 on:** November 14, 2017, 01:39:48 PM »

Frank, used stack height was 39.50, new 40.20mm

dragracer · « **Reply #85 on:** November 14, 2017, 01:41:43 PM »

Looks like you're wrapping this one up. Good job. I rolled mine out of the trailer so I could get the top gas bike out because it was strapped down in the rear. I then pushed it back in the trailer. I'd better get busy. 2 days left

Bill/BentON Racing · « **Reply #86 on:** January 27, 2018, 03:33:44 PM »

I'm back at it! Engine build time...lol.

Jerry Rxman Griffin aka MuthaF'er · « **Reply #87 on:** January 27, 2018, 06:40:50 PM »

Get em Bill! Looks good. Time to spare too

dragracer · « **Reply #88 on:** January 27, 2018, 10:18:31 PM »

Quote from: Bill/BentON Racing on January 27, 2018, 03:33:44 PM

I'm back at it! Engine build time...lol.

Roll on brother. Seems as if we're always trying to get something ready to race. Time is on your side right now. You could even be ready for some post season testing and maybe even make a few early season races prior to the Cup kickoff.

I'm going to do the best I can to drag myself in the shop tomorrow to start back working on the project F model. An old guy told me once that if you have a project, try to do at least one thing a day even when you don't feel like working. Eventually, it'll all get done.

Keep moving!!!

Medyo Bastos · « **Reply #89 on:** January 28, 2018, 04:29:33 AM »

Good advice Frankie! Keep n it Billie!

Sent from my iPhone using Tapatalk

Bill/BentON Racing · « **Reply #90 on:** January 28, 2018, 04:55:28 AM »

Yep, going pull top end today, check these out..... bottom one Cappallini, the best I've seen so far, definitely will free up some hp ,spins so freely top and bottom. Yes, it's pricey, $270.00 for what you see, but I like it. Bill
The new one above it I'll let go, it's been assembled, kmb69 was kind enough to help me out...$135.00 shipped 48 states

Bill/BentON Racing · « **Reply #91 on:** January 28, 2018, 05:16:47 PM »

Well, it's clean inside....lol

, Bill Time to disassemble.....

Bill/BentON Racing · « **Reply #92 on:** January 28, 2018, 06:52:12 PM »

Not too bad, about what we expected...

dragracer · « **Reply #93 on:** January 28, 2018, 08:49:38 PM »

You must have been running that crack fuel again. Lean😡

754 · « **Reply #94 on:** January 28, 2018, 09:30:12 PM »

Bill is that a collapsed O ring to left of cam roller.
When I wrecked my cam I had a sticking guide..? When I pulled it apart both those brings had shrunk up, like 2 flat sides.. strange.
I think good O rings stay soft but I pulled a set off the oil jets recently, that were hard as ever , can't bend they break.

Bill/BentON Racing · « **Reply #95 on:** January 29, 2018, 04:13:34 AM »

Nah, it stuck to the head, when I pulled it off some gasgacinch stuck to it and wrapped around etc. I think it was ok before that, good eye though. This cylinder and bore kit may be for sale.....decisions, decisions lol! Bill

PeWe · « **Reply #96 on:** January 30, 2018, 03:33:39 AM »

What about your JMR Big Block cylinder? Not in a build?

MRieck · « **Reply #97 on:** January 30, 2018, 05:12:08 AM »

Quote from: PeWe on January 30, 2018, 03:33:39 AM

What about your JMR Big Block cylinder? Not in a build?

For the automatic bike

PeWe · « **Reply #98 on:** January 30, 2018, 09:13:28 AM »

OK, an automatic can handle that? Turbine mod allowing higher rpm before take off too, right?
I have looked forward to see others using JMR Billet block, the result with various setups, cams etc.

MRieck · « **Reply #99 on:** January 30, 2018, 04:50:37 PM »

Quote from: PeWe on January 30, 2018, 09:13:28 AM

OK, an automatic can handle that? Turbine mod allowing higher rpm before take off too, right?
I have looked forward to see others using JMR Billet block, the result with various setups, cams etc.

Yes....there are others. I will dyno mine this spring. I really don't like the cam in it but that is a conversation for another time.

News:

Author Topic: Project B7 Underway! Billet Big Block Built By Bill BentON Racing (Read 62017 times)