Author Topic: CB550 white smoke after top end rebuild  (Read 3502 times)

0 Members and 1 Guest are viewing this topic.

Offline JB Stellies

  • Full Member
  • *
  • Posts: 18
  • 76 CB550
CB550 white smoke after top end rebuild
« on: December 05, 2018, 08:43:16 am »
I did a top end rebuild after incorrect installation of tappet cover resulting in bent exhaust valves (noob mistake- followed workshop manual without watching youtube tutorials). Now the bike is smoking like a two stroke. I outsourced the valve replacement as I did not have the tool to compress the valves and the mechanic ensures me that the valve guides were not cracked and that valve stem seals are OK. I used aftermarket generic o-rings on the oil channels either side of the head. If these were not thick enough, could it result in white smoke/what would the symptom be? I have ridden 15km, the bike is running well (other than the white smoke) and there are no visible external oil leaks. The bike was not smoking before the top end rebuild and I did not touch the bottom end so I am confident that the rings are OK.

Offline TwoTired

  • Really Old Timer ...
  • *******
  • Posts: 21,805
Re: CB550 white smoke after top end rebuild
« Reply #1 on: December 05, 2018, 09:08:16 am »
White smoke is water vapor, generally.
Blue smoke is oil smoke.

Are you certain that water condensate in the exhaust is not the source of the "smoke"?  Have the exhaust been thoroughly heated to flash off the condensate?

Are all head pipes getting evenly hot?

Cheers,
Lloyd... (SOHC4 #11 Original Mail List)
72 500, 74 550, 75 550K, 75 550F, 76 550F, 77 550F X2, 78 550K, 77 750F X2, 78 750F, 79CX500, 85 700SC, GL1100

Those that learn from history are doomed to repeat it by those that don't learn from history.

Offline JB Stellies

  • Full Member
  • *
  • Posts: 18
  • 76 CB550
Re: CB550 white smoke after top end rebuild
« Reply #2 on: December 05, 2018, 10:48:19 pm »
I am pretty sure it is oil and we are talking about a large amount of smoke. It is worse at first start up but smokes heavily and consistently thereafter. I will check if all exhausts are heating up evenly when I next ride.

Offline JB Stellies

  • Full Member
  • *
  • Posts: 18
  • 76 CB550
Re: CB550 white smoke after top end rebuild
« Reply #3 on: December 05, 2018, 10:52:28 pm »
PS - and yes, after 15km I think the bike was pretty hot and any condensate and residual oil from the rebuild should have burnt off. Thks

Offline TwoTired

  • Really Old Timer ...
  • *******
  • Posts: 21,805
Re: CB550 white smoke after top end rebuild
« Reply #4 on: December 06, 2018, 08:22:40 am »
Tell us how you routed the top engine vent hose.
Can the crankcase still "breathe"?

Cheers,
Lloyd... (SOHC4 #11 Original Mail List)
72 500, 74 550, 75 550K, 75 550F, 76 550F, 77 550F X2, 78 550K, 77 750F X2, 78 750F, 79CX500, 85 700SC, GL1100

Those that learn from history are doomed to repeat it by those that don't learn from history.

Offline JB Stellies

  • Full Member
  • *
  • Posts: 18
  • 76 CB550
Re: CB550 white smoke after top end rebuild
« Reply #5 on: December 07, 2018, 07:37:48 am »
I have not fitted a vent hose.

Offline Deltarider

  • Really Old Timer ...
  • *******
  • Posts: 7,853
  • Another big liar has to face the truth.
Re: CB550 white smoke after top end rebuild
« Reply #6 on: December 07, 2018, 07:54:22 am »
Well, there's the source of your smoke, probably
CB500K2-ED Excel black
"There is enough for everyone's need but not enough for anybody's greed."

Offline TwoTired

  • Really Old Timer ...
  • *******
  • Posts: 21,805
Re: CB550 white smoke after top end rebuild
« Reply #7 on: December 07, 2018, 09:22:43 am »
I have not fitted a vent hose.
Is the hose nipple open or plugged?
Lloyd... (SOHC4 #11 Original Mail List)
72 500, 74 550, 75 550K, 75 550F, 76 550F, 77 550F X2, 78 550K, 77 750F X2, 78 750F, 79CX500, 85 700SC, GL1100

Those that learn from history are doomed to repeat it by those that don't learn from history.

Offline JB Stellies

  • Full Member
  • *
  • Posts: 18
  • 76 CB550
Re: CB550 white smoke after top end rebuild
« Reply #8 on: December 12, 2018, 07:47:00 am »
Vent nipple is open, photo attached tv. Have been running it without a hose since I got tbe bike with no problem.

Offline Don R

  • My Sandcast is a
  • Really Old Timer ...
  • *******
  • Posts: 19,166
  • Saver of unloved motorcycles.
Re: CB550 white smoke after top end rebuild
« Reply #9 on: December 12, 2018, 08:09:33 am »
 My buddy ran across a breather tube filled with silicone, it caused a similar problem. Just my friends experience.
No matter how many times you paint over a shadow, it's still there.
If you love it, set it free, if it stays it's probably one of my 750's.
 CEO at the no kill motorcycle shop.

Offline TwoTired

  • Really Old Timer ...
  • *******
  • Posts: 21,805
Re: CB550 white smoke after top end rebuild
« Reply #10 on: December 12, 2018, 08:18:24 am »
Vent nipple is open, photo attached tv. Have been running it without a hose since I got tbe bike with no problem.

...Except for the bugs that crawl in and nest, or abrasive dust invasion.  Rain or wash water ingress?
And, if you do get excessive piston ring blow by, the engine oil sprays out of there covering the entire rear of the bike.  If it weren't a required item, why do you think Honda went to the expense of installing one on every bike they sold?  Give them a little credit, please.

Anyway, it's good that you didn't plug it off.  We can check crankcase pressure build up off the possible cause list.  I was looking for cheap and easy fixes.  Now it warrants a more serious investigation.

If you have excessive oil smoke, it is getting past the valve guide seals or the piston rings. (or leaking onto the exhaust system.)  Time for a leak down cylinder check, or at least a compression check, to ensure mechanical health of the cylinders.

Do the spark plug deposits show anything interesting?  Are they the same for each cylinder position?  Did you verify each head pipe runs at about equal temperature?  We need to know if all four pots are burning, or if one is just pumping fuel/air without igniting. If the latter, white fuel vapor out the exhaust is a possibility. 

Have you checked for spark at each position?

Cheers,

Lloyd... (SOHC4 #11 Original Mail List)
72 500, 74 550, 75 550K, 75 550F, 76 550F, 77 550F X2, 78 550K, 77 750F X2, 78 750F, 79CX500, 85 700SC, GL1100

Those that learn from history are doomed to repeat it by those that don't learn from history.

Offline JB Stellies

  • Full Member
  • *
  • Posts: 18
  • 76 CB550
Re: CB550 white smoke after top end rebuild
« Reply #11 on: December 12, 2018, 08:52:42 am »
Thanks gents. New rings about 1000km ago and did not touch the block and it was running fine before I took the head off so I am confident rings fine. My guess is that mechanic did not check for cracked valve guides and that one or more exhaust valve guides cracked when the valves bent. When I asked the mechanic if he checked he said he would need to check with the guy who did the work so my guess is he did not give clear instructions to his junior. Attached photo of smoking bike.

Offline PeWe

  • Really Old Timer ...
  • *******
  • Posts: 15,098
  • Bike almost back to the 70's 2015
Re: CB550 white smoke after top end rebuild
« Reply #12 on: December 12, 2018, 08:58:01 am »
Vent nipple is open, photo attached tv. Have been running it without a hose since I got tbe bike with no problem.
You have not felt any stinky warm oil smell right up in your face while waiting for green light with warm engine?

My CB750 K6 had a long hose from valve cover breather going backwards on right side to the rear passenger foot peg. Old hose hardened and cracked. Now a shorter one ending just behind main foot peg.
Std car 1/2" oil/heater hose work fine. A little bit thick... Honda used thinner walled hose without braiding.
CB750 K6-76 1005cc JMR Billet block.
CB750 K2-75 Parts assembled to a stock K2

Updates of the CB750 K6 -1976
http://forums.sohc4.net/index.php/topic,180468.msg2092136.html#msg2092136
The billet block build thread
http://forums.sohc4.net/index.php/topic,49438.msg1863571.html#msg1863571
CB750 K2 -1975  build thread
http://forums.sohc4.net/index.php/topic,168243.msg1948381.html#msg1948381
K2 engine build thread. For a complete CB750 -75
http://forums.sohc4.net/index.php/topic,180088.msg2088008.html#msg2088008
Carb jetting, a long story Mikuni TMR32
http://forums.sohc4.net/index.php/topic,179479.msg2104967.html#msg2104967

Offline JB Stellies

  • Full Member
  • *
  • Posts: 18
  • 76 CB550
Re: CB550 white smoke after top end rebuild
« Reply #13 on: December 12, 2018, 09:02:02 am »
Thanks, I will fit a hose when I put the engine back together again after sorting out the cause of the smoking.

Offline bryanj

  • Really Old Timer ...
  • *******
  • Posts: 13,449
  • CB500 Number 1000036
Re: CB550 white smoke after top end rebuild
« Reply #14 on: December 12, 2018, 01:36:32 pm »
If the valves were bent i would be 90% certain the guides were broken somehow. If you fit new they need to be ACCURATELY reamed to size and the seats re ground to suit.

The size reamer is not a "standard" size so unless it is a shop that does a lot of Hondas an adjustable one tends to get used and they are simply not good enough.
Semi Geriatric ex-Honda mechanic and MOT tester (UK version of annual inspection). Garage full of "projects" mostly 500/4 from pre 73 (no road tax in UK).

Remember "Its always in the last place you look" COURSE IT IS YOU STOP LOOKIN THEN!

Offline JB Stellies

  • Full Member
  • *
  • Posts: 18
  • 76 CB550
Re: CB550 white smoke after top end rebuild
« Reply #15 on: December 13, 2018, 06:21:34 am »
Thanks Bryanj. Will have a careful look at valve guides when it is in pieces again. I have a full spare engine in parts and may be better to use that head but cam chain tensioner broke on that engine and cam chain slipped so not sure what damage that may have caused to the head if any. Cannot see any visible damage to the head.

Offline bryanj

  • Really Old Timer ...
  • *******
  • Posts: 13,449
  • CB500 Number 1000036
Re: CB550 white smoke after top end rebuild
« Reply #16 on: December 13, 2018, 10:03:17 am »
Easy check to see if valves are reasonable is to stand head on exhaust outlets then fill inlets with gas or keroseen and see if any apears in combusion area then put head on inlets and fill exhaust. Easier to see which, if any, valves are leaking than the book way of filling combustion chamber.
Semi Geriatric ex-Honda mechanic and MOT tester (UK version of annual inspection). Garage full of "projects" mostly 500/4 from pre 73 (no road tax in UK).

Remember "Its always in the last place you look" COURSE IT IS YOU STOP LOOKIN THEN!

Offline JB Stellies

  • Full Member
  • *
  • Posts: 18
  • 76 CB550
Re: CB550 white smoke after top end rebuild
« Reply #17 on: December 13, 2018, 10:25:30 am »
Thanks Bryan, great tip.

Online calj737

  • Really Old Timer ...
  • *******
  • Posts: 20,809
  • I refuse...
Re: CB550 white smoke after top end rebuild
« Reply #18 on: December 13, 2018, 11:22:30 am »
Easy check to see if valves are reasonable is to stand head on exhaust outlets then fill inlets with gas or keroseen and see if any apears in combusion area then put head on inlets and fill exhaust. Easier to see which, if any, valves are leaking than the book way of filling combustion chamber.
This will only tell you whether or not the valve face is seating do sealing fully, not whether the guide is worn. You could easily have carbon build up on the valve face, preventing full seating, but good guides. Conversely, worn guides that under operating conditions allow the valve to move off their axis, but freshly lapped faces that seat.

Unless I’m missing something?
'74 550 Build http://forums.sohc4.net/index.php?topic=126401.0
'73 500 Build http://forums.sohc4.net/index.php?topic=132935.0

"Of all tyrannies, a tyranny sincerely exercised for the good of it's victim may be the most oppressive. It may be better to live under robber barons than under omnipotent moral busybodies. The robber baron's cruelty may sometimes sleep, his cupidity may at some point be satiated, but those who torment us for our own good will torment us without end for they do so with the approval of their own conscience." - C.S. Lewis

Offline JB Stellies

  • Full Member
  • *
  • Posts: 18
  • 76 CB550
Re: CB550 white smoke after top end rebuild
« Reply #19 on: December 13, 2018, 12:12:44 pm »
Makes sense unless you can look for gasoline leaking through on either side with that test (valve seat and stem ends)?

Online calj737

  • Really Old Timer ...
  • *******
  • Posts: 20,809
  • I refuse...
Re: CB550 white smoke after top end rebuild
« Reply #20 on: December 13, 2018, 12:20:19 pm »
Makes sense unless you can look for gasoline leaking through on either side with that test (valve seat and stem ends)?
Maybe I made my point in a confusing fashion, or I’m confused. I see where that technique addresses the valve seat. But I don’t see where it addresses valve guide wear.
Thanks Bryanj. Will have a careful look at valve guides when it is in pieces again.
Wasn’t that your point with this post?
'74 550 Build http://forums.sohc4.net/index.php?topic=126401.0
'73 500 Build http://forums.sohc4.net/index.php?topic=132935.0

"Of all tyrannies, a tyranny sincerely exercised for the good of it's victim may be the most oppressive. It may be better to live under robber barons than under omnipotent moral busybodies. The robber baron's cruelty may sometimes sleep, his cupidity may at some point be satiated, but those who torment us for our own good will torment us without end for they do so with the approval of their own conscience." - C.S. Lewis

Offline bryanj

  • Really Old Timer ...
  • *******
  • Posts: 13,449
  • CB500 Number 1000036
Re: CB550 white smoke after top end rebuild
« Reply #21 on: December 13, 2018, 01:08:06 pm »
It doesnt asses guide wear BUT it gives you a good idea of the valve/seat condition BEFORE you spend any money especially on a used head of unknown condition.

We already know that the fitted one has problems and when you get to valve/guide/seat replacement or repair it is frquently far more cost effective to find a good used head.
Semi Geriatric ex-Honda mechanic and MOT tester (UK version of annual inspection). Garage full of "projects" mostly 500/4 from pre 73 (no road tax in UK).

Remember "Its always in the last place you look" COURSE IT IS YOU STOP LOOKIN THEN!

Online calj737

  • Really Old Timer ...
  • *******
  • Posts: 20,809
  • I refuse...
Re: CB550 white smoke after top end rebuild
« Reply #22 on: December 13, 2018, 03:00:46 pm »
It doesnt asses guide wear BUT it gives you a good idea of the valve/seat condition BEFORE you spend any money especially on a used head of unknown condition.

We already know that the fitted one has problems and when you get to valve/guide/seat replacement or repair it is frquently far more cost effective to find a good used head.
That’s what I thought. Thanks for the clarification.
'74 550 Build http://forums.sohc4.net/index.php?topic=126401.0
'73 500 Build http://forums.sohc4.net/index.php?topic=132935.0

"Of all tyrannies, a tyranny sincerely exercised for the good of it's victim may be the most oppressive. It may be better to live under robber barons than under omnipotent moral busybodies. The robber baron's cruelty may sometimes sleep, his cupidity may at some point be satiated, but those who torment us for our own good will torment us without end for they do so with the approval of their own conscience." - C.S. Lewis

Offline JB Stellies

  • Full Member
  • *
  • Posts: 18
  • 76 CB550
Re: CB550 white smoke after top end rebuild
« Reply #23 on: December 13, 2018, 10:02:09 pm »
Thanks gents! Understood.

Offline JB Stellies

  • Full Member
  • *
  • Posts: 18
  • 76 CB550
Re: CB550 white smoke after top end rebuild
« Reply #24 on: December 13, 2018, 11:06:36 pm »
I need to order a gasket set from the US so will only tackle this project in January. Will keep you all posted then. Thanks to everyone for input and advice. My experience working on multi-cylinder four strokes is very limited.