Author Topic: Re-energized!  (Read 1944 times)

0 Members and 1 Guest are viewing this topic.

Offline azuredesign

  • Knupping pin
  • Master
  • *****
  • Posts: 1,705
Re-energized!
« on: June 11, 2020, 05:11:53 AM »
After a long hiatus, I have finally started again on my CB project after several years of benign neglect in the back of the garage. I am hoping that Marcel is still available to rebuild the speedo, in a box unsent, awaiting shipment to him from 8 years ago. If not, is there anyone in the states doing this work? Thanks for any help...glad to be back!

Offline slikwilli420

  • Master of Disaster
  • Master
  • *****
  • Posts: 2,362
Re: Re-energized!
« Reply #1 on: June 11, 2020, 11:16:55 AM »
Looks good! Really tasteful mods and no skateboard seat!
All you gotta do is do what you gotta do.

Vintage Speed Parts Mashup: http://forums.sohc4.net/index.php?topic=133638.0
Rickman CR Parts Kit Refresh: http://forums.sohc4.net/index.php/topic,154837.0.html
AHRMA CB750 Racer: http://forums.sohc4.net/index.php/topic,158461.0.html
AHRMA Superbike Heavyweight Racer: http://forums.sohc4.net/index.php/topic,173120.0.html
'76F CB750 Patina Redemption: http://forums.sohc4.net/index.php/topic,174871.0.html

Offline Pielz

  • Hot Shot
  • ***
  • Posts: 565
Re: Re-energized!
« Reply #2 on: June 11, 2020, 11:44:35 AM »
+1 to the no skateboard/caterpillar seat! How much did the spin on oil filter increase your oil capacity? Buddy of mine did that to his CX500 and it increased it by like 3/4 of a quart. Looks silly on his bike but doesn't look awful on yours!

Offline andy750

  • Really Old Timer ...
  • *******
  • Posts: 7,938
Re: Re-energized!
« Reply #3 on: June 11, 2020, 12:46:44 PM »
Hey Ben,

Glad to see the 750 again! Marcell is still doing gauges and is bigger than ever now. What else is the bike needing?

Good luck!
Andy
Current bikes
1. CB750K4: Long distance bike, 17 countries and counting...2001 - Trans-USA-Mexico, 2003 - European Tour, 2004 - SOHC Easy Rider Trip , 2008 - Adirondack Tour 2-up , 2013 - Tail of the Dragon Tour , 2017: 836 kit install and bottom end rebuild. And rebirth: http://forums.sohc4.net/index.php/topic,173213.msg2029836.html#msg2029836
2. CB750/810cc K2  - road racer with JMR worked head 71 hp
3. Yamaha Tenere T700 2022

Where did you go on your bike today? - http://forums.sohc4.net/index.php?topic=45183.2350

Offline SOHC4 Cafe Racer Fan

  • Speak up, Whipper-Snapper! I'm a
  • Really Old Timer ...
  • *******
  • Posts: 15,731
  • SOHC/4 Member #1235
Re: Re-energized!
« Reply #4 on: June 11, 2020, 03:39:06 PM »
After a long hiatus, I have finally started again on my CB project after several years of benign neglect in the back of the garage. I am hoping that Marcel is still available to rebuild the speedo, in a box unsent, awaiting shipment to him from 8 years ago. If not, is there anyone in the states doing this work? Thanks for any help...glad to be back!

I think Marcel is still at it.

Alternatively, I highly recommend Buz Ras aka Seattle Speedometer
Buz can rebuild any automotive gauge with precision.  If you like, he can customize your gauge, too.
http://seattlespeedometer.com/

hello@seattlespeedometer.com

Shop :: 509.925.4849

Shipping Address.
Seattle Speedometer
1581 Thomas Rd
Ellensburg, WA 98926
1975 CB550K1 "Blue" Stockish Restomod (http://forums.sohc4.net/index.php?topic=135005.0)
1975 CB550F1 frame/CB650 engine hybrid "The Hot Mess" (http://forums.sohc4.net/index.php/topic,150220.0.html)
2008 Triumph Thruxton (http://forums.sohc4.net/index.php/topic,190956.0.html)
2014 MV Agusta Brutale Dragster 800
2015 Yamaha FZ-09 (http://forums.sohc4.net/index.php/topic,186861.0.html)

"There are some things nobody needs in this world, and a bright-red, hunch-back, warp-speed 900cc cafe racer is one of them — but I want one anyway, and on some days I actually believe I need one.... Being shot out of a cannon will always be better than being squeezed out of a tube. That is why God made fast motorcycles, Bubba." Hunter S. Thompson, Song of the Sausage Creature, Cycle World, March 1995.  (http://www.latexnet.org/~csmith/sausage.html and https://magazine.cycleworld.com/article/1995/3/1/song-of-the-sausage-creature)

Sold/Emeritus
1973 CB750K2 "Bionic Mongrel" (http://forums.sohc4.net/index.php?topic=132734.0) - Sold
1977 CB750K7 "Nine Lives" Restomod (http://forums.sohc4.net/index.php?topic=50490.0) - Sold
2005 RVT1000RR RC51-SP2 "El Diablo" - Sold
2016+ Triumph Thruxton 1200 R (http://forums.sohc4.net/index.php/topic,170198.0.html) - Sold

Offline Stev-o

  • Ain't no
  • Really Old Timer ...
  • *******
  • Posts: 34,315
  • Central Texas
Re: Re-energized!
« Reply #5 on: June 11, 2020, 03:46:43 PM »
After a long hiatus, I have finally started again on my CB project after several years of benign neglect in the back of the garage. I am hoping that Marcel is still available to rebuild the speedo, in a box unsent, awaiting shipment to him from 8 years ago. If not, is there anyone in the states doing this work? Thanks for any help...glad to be back!

I think Marcel is still at it.

Alternatively, I highly recommend Buz Ras aka Seattle Speedometer
Buz can rebuild any automotive gauge with precision.  If you like, he can customize your gauge, to


Good info Don, thx for sharing.
Marcel is very good but shipping to Europe from U.S. has become very expensive.
He did the gauges for my upcoming K1 project.
'74 "Big Bang" Honda 750K [836].....'76 Honda 550F.....K3 Park Racer!......and a Bomber!............plus plus plus.........

Offline azuredesign

  • Knupping pin
  • Master
  • *****
  • Posts: 1,705
Re: Re-energized!
« Reply #6 on: June 11, 2020, 04:38:58 PM »
Hello and thanks all, and hello to my friend and fellow NE Honda Guys member, Andy750. I contacted a US based fellow...there are certainly many more mechanical instrument rebuilding places now than when I last looked!

Andy, I am still tuning a bit, but she ran strong after I gave the carbs some love yesterday. Running at about 140f yesterday at the drain plug sensor. I may need to install a bypass for the oil cooler, am monitoring..I have yet to fab a housing and install idiot lights. As well I might shorten the Racetech preload slugs in the front suspension, as I was a bit heavier when I made them. Aside from an oil change, which now takes about a quart more than stock, and valve check...think I am all set.
« Last Edit: June 11, 2020, 04:40:45 PM by azuredesign »

Offline Alan F.

  • We remember the Night Rider, and we know who you are.
  • Really Old Timer ...
  • *******
  • Posts: 7,347
Re: Re-energized!
« Reply #7 on: June 11, 2020, 06:05:12 PM »
Good to hear from you Brother, I've been toying with a K8 for a little while, waiting on parts right now. Its sure easier than carrying my K3 out of the basement where we left it.

Offline andy750

  • Really Old Timer ...
  • *******
  • Posts: 7,938
Re: Re-energized!
« Reply #8 on: June 11, 2020, 07:11:18 PM »
Hey Ben sounds like you are real close. I love your bike and would love to see it run!
Current bikes
1. CB750K4: Long distance bike, 17 countries and counting...2001 - Trans-USA-Mexico, 2003 - European Tour, 2004 - SOHC Easy Rider Trip , 2008 - Adirondack Tour 2-up , 2013 - Tail of the Dragon Tour , 2017: 836 kit install and bottom end rebuild. And rebirth: http://forums.sohc4.net/index.php/topic,173213.msg2029836.html#msg2029836
2. CB750/810cc K2  - road racer with JMR worked head 71 hp
3. Yamaha Tenere T700 2022

Where did you go on your bike today? - http://forums.sohc4.net/index.php?topic=45183.2350

Offline andy750

  • Really Old Timer ...
  • *******
  • Posts: 7,938
Re: Re-energized!
« Reply #9 on: June 11, 2020, 07:12:06 PM »
Hey Alan if you need parts let me know what you need...I may have it!
Current bikes
1. CB750K4: Long distance bike, 17 countries and counting...2001 - Trans-USA-Mexico, 2003 - European Tour, 2004 - SOHC Easy Rider Trip , 2008 - Adirondack Tour 2-up , 2013 - Tail of the Dragon Tour , 2017: 836 kit install and bottom end rebuild. And rebirth: http://forums.sohc4.net/index.php/topic,173213.msg2029836.html#msg2029836
2. CB750/810cc K2  - road racer with JMR worked head 71 hp
3. Yamaha Tenere T700 2022

Where did you go on your bike today? - http://forums.sohc4.net/index.php?topic=45183.2350

Offline Alan F.

  • We remember the Night Rider, and we know who you are.
  • Really Old Timer ...
  • *******
  • Posts: 7,347
Re: Re-energized!
« Reply #10 on: June 11, 2020, 07:18:48 PM »
Thanks, I'll let you know. I'm back to work this week so will be losing momentum on the build. Fingers crossed I can find some time to spend doing what I can.

Offline hondaron

  • Full Member
  • *
  • Posts: 68
Re: Re-energized!
« Reply #11 on: June 11, 2020, 07:43:48 PM »
For gauges check out www.rcycle.com
 
Randy recently helped me out with a DOHC 900F gauge  repair and a early model CB750 gauge repair
😊

Offline azuredesign

  • Knupping pin
  • Master
  • *****
  • Posts: 1,705
Re: Re-energized!
« Reply #12 on: June 12, 2020, 03:56:54 AM »
Good to hear from you Brother, I've been toying with a K8 for a little while, waiting on parts right now. Its sure easier than carrying my K3 out of the basement where we left it.

Hey Aan,

Glad to get your note, thanks brother! Happy to help if there is something I can do to get your ride together. Best wishes!!

Offline azuredesign

  • Knupping pin
  • Master
  • *****
  • Posts: 1,705
Re: Re-energized!
« Reply #13 on: June 12, 2020, 03:58:30 AM »
For gauges check out www.rcycle.com
 
Randy recently helped me out with a DOHC 900F gauge  repair and a early model CB750 gauge repair
😊

Thank you!!

Offline azuredesign

  • Knupping pin
  • Master
  • *****
  • Posts: 1,705
Re: Re-energized!
« Reply #14 on: June 12, 2020, 04:10:38 AM »
Hey Ben sounds like you are real close. I love your bike and would love to see it run!

Would love to go for a ride with you, and you're always welcome here. I am back to bike work after a number of years off, although I get sidetracked with other projects...now excavating for a steel 24x24 garage for yard equipment.
I have a bunch of other cool projects that I have started working on again, the srx-6 that Anders and I picked up a few years back, my FJ which now has updated and not yet functional carbs, and a few I have not yet touched...a tx650 that hopefully looks new OEM, the RZ350 that I still haven't got tuned right, an r1100s in pieces, and the sv650. So hands full!! Best wishes to you, and look forward to meeting up!

Offline knowsnothing

  • Hot Shot
  • ***
  • Posts: 643
Re: Re-energized!
« Reply #15 on: June 12, 2020, 09:02:19 AM »
Nice work Ben  ;)
1978 CB750k Green - 811 engine
1978 CB750k Blue - for sale
1974 CB375F Faded Black - had to have that 6th gear
1976 CB400F Red - in many pieces
1973 CB350F TBD - in many pieces

Offline MauiK3

  • A K3 is saved
  • Old Timer
  • ******
  • Posts: 4,280
  • Old guy
Re: Re-energized!
« Reply #16 on: June 12, 2020, 09:29:38 AM »
Marcel and company are tops, my gauges look great.
1973 CB 750 K3
10/72 build Z1 Kawasaki

Offline azuredesign

  • Knupping pin
  • Master
  • *****
  • Posts: 1,705
Re: Re-energized!
« Reply #17 on: June 12, 2020, 09:37:40 AM »
Nice work Ben  ;)

Thanks Treve, hope your brood is doing well, folks and bikes!!

Offline azuredesign

  • Knupping pin
  • Master
  • *****
  • Posts: 1,705
Re: Re-energized!
« Reply #18 on: June 12, 2020, 09:38:38 AM »
Marcel and company are tops, my gauges look great.


Glad to hear with thanks!

Offline grcamna2

  • Not a
  • Really Old Timer ...
  • *******
  • Posts: 15,139
  • I love to restore & travel. Keep'em Going Strong !
Re: Re-energized!
« Reply #19 on: June 12, 2020, 10:21:33 AM »
subscribed
75' CB400F/'bunch o' parts' & 81' CB125S modded to a 'CB200S'
  I love the small ones too !
Do your BEST...nobody can take that away from you.