« previous next »
Pages: 1 2 3 [4]   Go Down

Author Topic: 71 CB500 - this will be work  (Read 7017 times)

0 Members and 1 Guest are viewing this topic.

Offline calj737

  • Really Old Timer ...
  • *******
  • Posts: 21,026
  • I refuse...
Re: 71 CB500 - this will be work
« Reply #75 on: October 29, 2024, 03:55:07 AM »
Now would be a great time to grease that swingarm pivot bushing too. Bet you’ll find it needs some deep love too.
Logged
'74 550 Build http://forums.sohc4.net/index.php?topic=126401.0
'73 500 Build http://forums.sohc4.net/index.php?topic=132935.0

"Of all tyrannies, a tyranny sincerely exercised for the good of it's victim may be the most oppressive. It may be better to live under robber barons than under omnipotent moral busybodies. The robber baron's cruelty may sometimes sleep, his cupidity may at some point be satiated, but those who torment us for our own good will torment us without end for they do so with the approval of their own conscience." - C.S. Lewis

Offline cheddarGoblin

  • Enthusiast
  • **
  • Posts: 151
Re: 71 CB500 - this will be work
« Reply #76 on: October 29, 2024, 03:56:59 AM »
Now it is time to do something about this rear wheel. I have been wanting to get to it but have been dreading it a little.


And will have to work on the brakes





This thing had a 5.1 inch tire on the back...it mostly fit.


The tire was a struggle. I've removed some dry and crusty tires before but this one seemed extra tough.


Looks like I am missing one of the sprocket nut retainers (not sure of correct name yet)


There is a little bit of rust to clean up here...


Got the sprocket off. Thought about replacing it while it is off, not sure if it even needs it though.


I am going to replace the bearings since I am already this far. So now to the bearing reatainer.
Logged
It seemed like a good idea at the time

1975 CB200T
1982 Nighthawk 650
1981 GL500
1971 CB500
1972 CL350

Offline cheddarGoblin

  • Enthusiast
  • **
  • Posts: 151
Re: 71 CB500 - this will be work
« Reply #77 on: October 29, 2024, 04:03:04 AM »
Quote from: calj737 on October 29, 2024, 03:55:07 AM
Now would be a great time to grease that swingarm pivot bushing too. Bet you’ll find it needs some deep love too.

I've realized I need to check the swingarms on all my bikes. I did check this one though before I took the wheel off, and did not notice any play, so hopefully all it needs is grease.
Logged
It seemed like a good idea at the time

1975 CB200T
1982 Nighthawk 650
1981 GL500
1971 CB500
1972 CL350

Offline Oddjob

  • Hot Shot
  • ***
  • Posts: 490
Re: 71 CB500 - this will be work
« Reply #78 on: October 29, 2024, 04:24:17 AM »
Is the ball bearing still inside the clutch adjuster?
Logged

Offline RAFster122s

  • I feel like a really really
  • Really Old Timer ...
  • *******
  • Posts: 12,352
  • SOHC4 member # 2605
Re: 71 CB500 - this will be work
« Reply #79 on: October 29, 2024, 04:30:04 AM »
That sprocket is toast...
OEM bearing retainers are NLA from Honda but aftermarket are available. There is a good bearing retainer wrench DSS carries and is also sold on away that makes that retainer much easier to remove after you drill the staked holes. Gonna need either a bench with dogs to clamp wheel down or someone else to hold it to get the needed leverage. It is a bear to remove by yourself.
The wrench has a machined cylinder with properly spaced pins to engage the holes in the retainer with a long arm to the wrench to give you the leverage. Once you get it started moving it becomes much easier. If you don't drill the stakes over threads the retainer is likely to wreck the threads on the hub.

Nico abrasives makes a synthetic string wheel that can clean up and even remove some of the rubbing in the hub. The ribbing area in the center of the casting is very coarse and tough to get clean. ScotchBrite pads can clean up the rest of the hub if you aren't planning to polish it, lots of tricky areas to sand and polish if you are looking to make it very shiny...
Logged
David- back in the desert SW!

Offline Oddjob

  • Hot Shot
  • ***
  • Posts: 490
Re: 71 CB500 - this will be work
« Reply #80 on: October 29, 2024, 04:46:04 AM »
That's not a 500 rear wheel. The studs don't come out like that, possibly 400/4?
Logged

Offline cheddarGoblin

  • Enthusiast
  • **
  • Posts: 151
Re: 71 CB500 - this will be work
« Reply #81 on: October 29, 2024, 06:07:55 PM »
Quote from: Oddjob on October 29, 2024, 04:24:17 AM
Is the ball bearing still inside the clutch adjuster?
Yep it is there. Everything seemed to operate pretty smoothly once reassembled.
Logged
It seemed like a good idea at the time

1975 CB200T
1982 Nighthawk 650
1981 GL500
1971 CB500
1972 CL350

Offline cheddarGoblin

  • Enthusiast
  • **
  • Posts: 151
Re: 71 CB500 - this will be work
« Reply #82 on: October 29, 2024, 06:13:45 PM »
Quote from: Oddjob on October 29, 2024, 04:46:04 AM
That's not a 500 rear wheel. The studs don't come out like that, possibly 400/4?
Wow! It seems you are right, good eye!

I checked the parts fiche and it looks like it is from a CB450.


Now I am not sure if I should continue rebuilding it or look for a correct wheel. I had already gotten it complete disassembled before seeing your post.
Logged
It seemed like a good idea at the time

1975 CB200T
1982 Nighthawk 650
1981 GL500
1971 CB500
1972 CL350

Offline calj737

  • Really Old Timer ...
  • *******
  • Posts: 21,026
  • I refuse...
Re: 71 CB500 - this will be work
« Reply #83 on: October 29, 2024, 07:15:09 PM »
I might have a spare 500 hub that would be completely usable. Oddly enough, I probably live less than 20’ from you.

I just had a peek in the parts cave, and sure enough I have a rear hub in perfect condition with new bearings and plush cush rubbers. You’ll just need to lace it to a rim. Send me a PM if you’d like it.
« Last Edit: October 29, 2024, 07:40:50 PM by calj737 »
Logged
'74 550 Build http://forums.sohc4.net/index.php?topic=126401.0
'73 500 Build http://forums.sohc4.net/index.php?topic=132935.0

"Of all tyrannies, a tyranny sincerely exercised for the good of it's victim may be the most oppressive. It may be better to live under robber barons than under omnipotent moral busybodies. The robber baron's cruelty may sometimes sleep, his cupidity may at some point be satiated, but those who torment us for our own good will torment us without end for they do so with the approval of their own conscience." - C.S. Lewis

Offline grcamna2

  • Not a
  • Really Old Timer ...
  • *******
  • Posts: 15,130
  • I love to restore & travel. Keep'em Going Strong !
Re: 71 CB500 - this will be work
« Reply #84 on: October 30, 2024, 12:59:17 AM »
Quote from: calj737 on October 29, 2024, 07:15:09 PM
I might have a spare 500 hub that would be completely usable. Oddly enough, I probably live less than 20’ from you.

I just had a peek in the parts cave, and sure enough I have a rear hub in perfect condition with new bearings and plush cush rubbers. You’ll just need to lace it to a rim. Send me a PM if you’d like it.

Excellent 'save'  ;)
Logged
75' CB400F/'bunch o' parts' & 81' CB125S modded to a 'CB200S'
  I love the small ones too !
Do your BEST...nobody can take that away from you.

Offline cheddarGoblin

  • Enthusiast
  • **
  • Posts: 151
Re: 71 CB500 - this will be work
« Reply #85 on: October 30, 2024, 03:06:34 AM »
Quote from: calj737 on October 29, 2024, 07:15:09 PM
I might have a spare 500 hub that would be completely usable. Oddly enough, I probably live less than 20’ from you.

I just had a peek in the parts cave, and sure enough I have a rear hub in perfect condition with new bearings and plush cush rubbers. You’ll just need to lace it to a rim. Send me a PM if you’d like it.

Awesome! Will do!
Logged
It seemed like a good idea at the time

1975 CB200T
1982 Nighthawk 650
1981 GL500
1971 CB500
1972 CL350

Offline cheddarGoblin

  • Enthusiast
  • **
  • Posts: 151
Re: 71 CB500 - this will be work
« Reply #86 on: October 30, 2024, 03:22:57 AM »
I completed the below right before checking this thread and finding out the wheel was from a different bike. :)

I've had this tool for years, I think it was to disassemble a hub from a Nissan that I no longer own. I was able to modify it to fit into the holes of the bearing retainer. The "pins" were very thin but with some heat and PB Blaster, the bearing retainer came out.


Not sure how this bearing spacer could have gotten this bent up.




Just a reference for wheel condition and to make sure I get it laced properly.



Zip, zip


And. it's apart.
Logged
It seemed like a good idea at the time

1975 CB200T
1982 Nighthawk 650
1981 GL500
1971 CB500
1972 CL350

Offline cheddarGoblin

  • Enthusiast
  • **
  • Posts: 151
Re: 71 CB500 - this will be work
« Reply #87 on: November 10, 2024, 04:50:54 AM »
I have to give a HUGE thank you to CalJ737 for getting me setup with the proper hub. He not only generously provided it but even delivered it! I will be making a donation to the site at per his suggestion but first I have to find my checkbook :)

Not only did he provide the proper hub, it's even clean and ready to go, (and ceramic coated I think?) saving me a ton of time as well cleaning the wrong one.



I wasn't sure if the brake would fit properly or I would need something else but so far I haven't found anything else I need for reassembly.


The rim was in rough shape. Electrolysis is my new favorite method of rust removal. It still took a couple baths and some wire wheel work to get it ready but eventually got all the rust removed. Once I got it clean, I put a thin layer of clearcoat on it.


I got it loosely laced. Ready to install the bearings (that even came with the hub!) and true it up. The hub was so nice I had reservations about using the existing rim as it still had some gouges and pits that weren't going anywhere. But the bike is going to have patina anyway, so had to move forward.


Thanks again Cal!
Logged
It seemed like a good idea at the time

1975 CB200T
1982 Nighthawk 650
1981 GL500
1971 CB500
1972 CL350

Offline newday777

  • Really Old Timer ...
  • *******
  • Posts: 5,242
  • Avatar is my 76 K6 in Colorado w/Cody on back 1980
Re: 71 CB500 - this will be work
« Reply #88 on: November 10, 2024, 06:09:24 AM »
Progress is always a good feeling
Logged
Stu
Honda Parts manager in the mid 1970s Nashua Honda
My current rides
1975 K5 Planet Blue my summer ride, it was a friend's bike I worked with at the Honda shop in 76, lots of fun to be on it again
1976 K6 Anteres Red rebuilding project, was originally my brother's that I set up from the crate, it'll breath again soon!
Project 750s, 2 K4, 2 K6, 1 K8
2008 GL1800 my daily ride and cross country runner

Prior bikes....
1972 Suzuki GT380 I had charge of it for a year in 1973 while my friend was deployed and learned to love street riding....
New CB450 K7 after my friend returned...
New CB750 K5 Planet Blue, demise by ex cousin in law at 9,000 miles...
New CB750 K6 Anteres Red, to replace the totaled K5, I sold this K6 at 45k in 1983, I had heavily modified it, many great memories on it and have missed it greatly.....
1983 GL1100A, 1999 GL1500 SE, 1999 GL1500A

Offline RAFster122s

  • I feel like a really really
  • Really Old Timer ...
  • *******
  • Posts: 12,352
  • SOHC4 member # 2605
Re: 71 CB500 - this will be work
« Reply #89 on: November 10, 2024, 11:49:01 AM »
Congrats on the progress and good on you Calj
Logged
David- back in the desert SW!

Offline Stev-o

  • Ain't no
  • Really Old Timer ...
  • *******
  • Posts: 34,300
  • Central Texas
Re: 71 CB500 - this will be work
« Reply #90 on: November 12, 2024, 07:16:55 AM »
Quote from: cheddarGoblin on November 10, 2024, 04:50:54 AM
I have to give a HUGE thank you to CalJ737 for getting me setup...

I dont care what anyone says, Cal is a great guy!!  Ha
Logged
'74 "Big Bang" Honda 750K [836].....'76 Honda 550F.....K3 Park Racer!......and a Bomber!............plus plus plus.........
Pages: 1 2 3 [4]   Go Up
« previous next »