« previous next »
Pages: 1 [2]  All   Go Down

Author Topic: Is this fixable?  (Read 1241 times)

0 Members and 1 Guest are viewing this topic.

Offline HondaMan

  • Someone took this pic of me before I became a
  • Really Old Timer ...
  • *******
  • Posts: 13,781
  • ...not my choice, I was nicknamed...
    • Getting 'em Back on the Road
Re: Is this fixable?
« Reply #25 on: June 29, 2023, 06:33:15 PM »
Try fitting that alternator cover onto the side of the cases. See if the hole aligns well with the one in the alternator cover, as both ends of this shaft are supported.
Logged
See SOHC4shop@gmail.com for info about the gadgets I make for these bikes.

The demons are repulsed when a man does good. Use that.
Blood is thicker than water, but motor oil is thicker yet...so, don't mess with my SOHC4, or I might have to hurt you.
Hondaman's creed: "Bikers are family. Treat them accordingly."

Link to Hondaman Ignition: http://forums.sohc4.net/index.php?topic=67543.0

Link to My CB750 Book: https://www.lulu.com/search?adult_audience_rating=00&page=1&pageSize=10&q=my+cb750+book

Link to website: www.SOHC4shop.com

Offline BenelliSEI

  • Really Old Timer ...
  • *******
  • Posts: 9,798
  • 1969 cb750
Re: Is this fixable?
« Reply #26 on: June 30, 2023, 05:24:34 AM »
Nice work. Saved another one!
Logged

Offline Gamma

  • Hot Shot
  • ***
  • Posts: 502
  • Bike Magazine august 1980 page 71. me on my F1
Re: Is this fixable?
« Reply #27 on: June 30, 2023, 05:32:26 AM »
Looks good
Logged

Offline Tracksnblades1

  • My Son was a collegiate competition Trap, Skeet, and sporting Clay
  • Master
  • *****
  • Posts: 1,851
Re: Is this fixable?
« Reply #28 on: June 30, 2023, 07:47:49 AM »
👍😁

Did you get charged over 2hrs total ?
Logged
Age Quod Agis

Offline tool14

  • Expert
  • ****
  • Posts: 790
Re: Is this fixable?
« Reply #29 on: June 30, 2023, 10:13:55 AM »
nice repair job.
Logged

Offline Rookster

  • Hot Shot
  • ***
  • Posts: 728
Re: Is this fixable?
« Reply #30 on: June 30, 2023, 05:59:51 PM »
I was charged 1 hour for the weld at $130 per hour.  The rest of the cost was from the machine shop.  The total was under $400.  I have to go back out there and pick up a fixture that the machinist made to get the shaft in the right position.  The welder told me that the fixture was most of the cost from the machine shop and since I paid for it then I should have it.  Overall I am very pleased with the work.  It was a quick turn around and cost less than I expected.  I will post a picture of the fixture once I get it.  Probably late next week or so. 

Scott
Logged

Offline grcamna2

  • Not a
  • Really Old Timer ...
  • *******
  • Posts: 15,087
  • I love to restore & travel. Keep'em Going Strong !
Re: Is this fixable?
« Reply #31 on: June 30, 2023, 06:12:00 PM »
Quote from: Rookster on June 30, 2023, 05:59:51 PM
I was charged 1 hour for the weld at $130 per hour.  The rest of the cost was from the machine shop.  The total was under $400.  I have to go back out there and pick up a fixture that the machinist made to get the shaft in the right position.  The welder told me that the fixture was most of the cost from the machine shop and since I paid for it then I should have it.  Overall I am very pleased with the work.  It was a quick turn around and cost less than I expected.  I will post a picture of the fixture once I get it.  Probably late next week or so. 

Scott

The service they provided was top-notch;even going as far as building a fixture to exactly line-up the shaft to have the welder set it up for a precision job.  ;)
« Last Edit: July 01, 2023, 08:54:40 PM by grcamna2 »
Logged
75' CB400F/'bunch o' parts' & 81' CB125S modded to a 'CB200S'
  I love the small ones too !
Do your BEST...nobody can take that away from you.

Offline Tracksnblades1

  • My Son was a collegiate competition Trap, Skeet, and sporting Clay
  • Master
  • *****
  • Posts: 1,851
Re: Is this fixable?
« Reply #32 on: July 01, 2023, 08:53:38 PM »
Quote from: Rookster on June 30, 2023, 05:59:51 PM
I was charged 1 hour for the weld at $130 per hour.  The rest of the cost was from the machine shop.  The total was under $400.  I have to go back out there and pick up a fixture that the machinist made to get the shaft in the right position.  The welder told me that the fixture was most of the cost from the machine shop and since I paid for it then I should have it.  Overall I am very pleased with the work.  It was a quick turn around and cost less than I expected.  I will post a picture of the fixture once I get it.  Probably late next week or so. 

Scott

It sounds twice as high as I was thinking….Oh wait everything is twice as high now…

Looks good….Post a picture of your fixture to locate the hole or shaft…I can only see what I’d do, but I like how others tackle the same..
Logged
Age Quod Agis
Pages: 1 [2]  All   Go Up
« previous next »