« previous next »
Pages: [1]   Go Down

Author Topic: where to get some oddball pieces  (Read 1746 times)

0 Members and 1 Guest are viewing this topic.

playinsafe44

  • Guest
where to get some oddball pieces
« on: July 16, 2007, 03:28:40 PM »
im in the middle of rebuilding some cb500 carbs (627B) and i was wondering where to get the little felt type of seals that go on the choke shaft, and also where to get the o-rings that go on the fuel T's. there are 8 o-rings that are the same size.
Logged

tbone

  • Guest
Re: where to get some oddball pieces
« Reply #1 on: July 16, 2007, 04:05:18 PM »
Logged

playinsafe44

  • Guest
Re: where to get some oddball pieces
« Reply #2 on: July 16, 2007, 09:23:06 PM »
i just looked at that site you posted, and its very helpful and i will use it in the future. but the o-rings look like they are only included in a gasket kit that is about 10 bucks, and it says 4 are required. i already have the carb rebuild kits. i was just wondering if anyone else has ran into this problem and what they did to fix it.
Logged

Steelo

  • Guest
Re: where to get some oddball pieces
« Reply #3 on: July 16, 2007, 10:07:18 PM »
I found some very attractive pink felt and cut some with a set of hole punches. Now dust has turned the pink to a sensitive new age pink brown!
Logged

playinsafe44

  • Guest
Re: where to get some oddball pieces
« Reply #4 on: July 16, 2007, 10:09:13 PM »
haha so you did use just some standard felt, cut it to fit, and have had no problems? if so that sounds like a great fix. (cheap) now all im really worried about is getting these o-rings.
Logged

Offline bryanj

  • Really Old Timer ...
  • *******
  • Posts: 14,025
  • CB500 Number 1000036
Re: where to get some oddball pieces
« Reply #5 on: July 16, 2007, 10:24:07 PM »
"O" ring part number 16173-044-004 size 7.8 x 1.9 (mm). felt seal was never available seperate from complete carb
Logged
Semi Geriatric ex-Honda mechanic and MOT tester (UK version of annual inspection). Garage full of "projects" mostly 500/4 from pre 73 (no road tax in UK).

Remember "Its always in the last place you look" COURSE IT IS YOU STOP LOOKIN THEN!

playinsafe44

  • Guest
Re: where to get some oddball pieces
« Reply #6 on: July 16, 2007, 11:16:53 PM »
thanks for the help!
Logged

rsvp9146

  • Guest
Re: where to get some oddball pieces
« Reply #7 on: July 17, 2007, 12:16:22 AM »
FYI, any good auto parts store will have the o rings

I got mine at Schucks
Logged

playinsafe44

  • Guest
Re: where to get some oddball pieces
« Reply #8 on: July 17, 2007, 03:08:56 PM »
im going to a bunch of stores today to try and get those o-rings. but the more i look at that felt choke shaft seal, the more difficult it looks to make. is there a trick to making these? i have one i can use as a copy. its a really thin ring of felt. im sure i can make the outside edge out with scissors, but the inside edge will be the challenge. any suggestions?
Logged

Offline merc2dogs

  • Hot Shot
  • ***
  • Posts: 625
Re: where to get some oddball pieces
« Reply #9 on: July 17, 2007, 06:27:56 PM »
 
 Two short chunks of tubing of the right size, sharpen the edge and tap it with a hammer.
 
 I've got a collection of spent shells and odd chunks of tube for that purpose in the junk drawer.

Ken.
Logged

playinsafe44

  • Guest
Re: where to get some oddball pieces
« Reply #10 on: July 17, 2007, 11:38:28 PM »
yea i ended up going to the crafts store, getting some felt and a cheap leather hole punch set. it didnt really work at all. i just put the carb back together, i think it should be alright without it. (at least i hope so). it does have the plastic washers pushed against the carbs, and its all tight, and when the choke is open it doesnt matter anyways.
Logged
Pages: [1]   Go Up
« previous next »