« previous next »
Pages: [1]   Go Down

Author Topic: float hight tool  (Read 1874 times)

0 Members and 1 Guest are viewing this topic.

Buffo

  • Guest
float hight tool
« on: July 05, 2005, 08:49:09 PM »
I had to check the float hight on my 1978 CB750K8, not a big deal. But I needed a smaller ruler so i went to wal-fart and nothing,but Radio shack ...

Radio Shack has a little depth gauge by Kronus. It costs $1.99 and has a lifetime warranty. It's marked in 1/64 and 1mm increments. It is a whole lot easier to use it than a ruler cause u just set the little slide and badda bing, your done.

anyway

Don
Logged

Offline kghost

  • Really Old Timer ...
  • *******
  • Posts: 6,855
  • www.facebook.com/RetroMecanicaAustralia
Re: float hight tool
« Reply #1 on: July 05, 2005, 09:02:59 PM »
Yeah, I just make a Go-No Go gauge out of scrap aluminum, Costs about .01. Works faster to set up the carbs too,
Logged
Stranger in a strange land

x2qwk4ux

  • Guest
Re: float hight tool
« Reply #2 on: July 05, 2005, 09:35:43 PM »
I just use a bench-grinder, micrometer, and an old Compact Disc case 8) 
Logged

Offline Dennis

  • Hot Shot
  • ***
  • Posts: 721
Re: float hight tool
« Reply #3 on: July 05, 2005, 10:04:32 PM »
Hey Buffo,
Do you have the Radio Sh!+ part number?
Thanks
Logged

Offline Raul CB750K1

  • Old Timer
  • ******
  • Posts: 3,881
Re: float hight tool
« Reply #4 on: July 06, 2005, 12:23:05 AM »
I also used a go-no go with a piece of cardboard. You don't have to keep it for the next time...


Raul
Logged

Offline Terry in Australia

  • Really Old Timer ...
  • *******
  • Posts: 33,321
  • So, what do ya wanna talk about today?
Re: float hight tool
« Reply #5 on: July 06, 2005, 03:34:45 AM »
I bought the original factory tool when I had my K1 20-odd years ago, but gave the tool to one of my CB750 riding mates, because I bought a Harley Sporster and assumed that this American icon would not have any similar components, only to discover it was fitted with a Keihin carb in the factory! (not to mention showa forks and shocks, Nippon Denso gauges, etc) Ah well, now i just use my Taiwanese digital vernier caliper, $16.99 on EvilBay! Cheers, Terry. ;D
Logged
I was feeling sorry for myself because I couldn't afford new bike boots, until I met a man with no legs.

So I said, "Hey mate, you haven't got any bike boots you don't need, do you?"

"Crazy is a very misunderstood term, it's a fine line that some of us can lean over and still keep our balance" (thanks RB550Four)

Buffo

  • Guest
Re: float hight tool
« Reply #6 on: July 07, 2005, 08:32:56 PM »
sorry for not getting you the part number sooner but I couldnt log onto this site for a little over a day for some reason ???

the part/catalog number is 64-2975


Don
Logged

migopod

  • Guest
Re: float hight tool
« Reply #7 on: July 07, 2005, 09:00:19 PM »
I had this crappy vermier caliper that i got to measure IDs more than ODs, but the ID end
didn't actually measure from zero.  I needed a float height gague, so i carefully removed the
set screw and reversed the outer jaw of the caliper so that it's offset, calibrated it and found that it works
quite perfectly (plus it's adjustable!)
Logged
Pages: [1]   Go Up
« previous next »