« previous next »
Pages: [1]   Go Down

Author Topic: Sleeves  (Read 1141 times)

0 Members and 1 Guest are viewing this topic.

Offline beelsamin

  • Enthusiast
  • **
  • Posts: 199
Sleeves
« on: December 22, 2007, 12:47:43 PM »
Can someone run me through the procedure for removing the piston sleeves and pressing in new....I know,I know,don't try this at home. ;)
I'm just curious as to what a shop would need to do when new sleeves are required.
Thanks
Logged
1977 Suzuki GT750
1972 Honda CB750 K2
1978 Honda CB550K

Offline 754

  • Really Old Timer ...
  • *******
  • Posts: 29,050
Re: Sleeves
« Reply #1 on: December 22, 2007, 01:00:37 PM »
Warm an oven up to 375 deg..
 wait about 30 minutes, wear oven mitts and push them out.

Try to find a shop oven somewhere or  you may be living in the shop..

 When you reinstall support the cylinder, push them in and hold them down while they cool.
Logged
Maker of the WELDLESS 750 Frame Kit
dodogas99@gmail.com
Kelowna B.C.       Canada

My next bike will be a ..ANFOB.....

It's All part of the ADVENTURE...

73 836cc.. Green, had it for 3 decades!!
Lost quite a few CB 750's along the way

Offline scunny

  • Old Timer
  • ******
  • Posts: 4,615
  • don't call me expert
Re: Sleeves
« Reply #2 on: December 22, 2007, 01:07:32 PM »
don't forget to remove the O rings from the sleeves  ;D
Logged
past-cb100,ts250,cb500,cb500,gs1000,gs650g.phillips traveller
present-CB 650 retro
            VTR1000F3
           XL250S riverbed rocket
           TS250[sold]
           TS185[sold]
           XL125S[sold]
           MT50 (white)
           MT50 (red)[sold]
           KN250/XS400 project
           XR/XL250 bitsa under construction
           SL100[sold]
           XL250R
           pedal(pub bike) leaks oil
my gallery http://gallery.sohc4.net/members/personal/scunny

newcbguy

  • Guest
Re: Sleeves
« Reply #3 on: December 22, 2007, 02:07:33 PM »
heating them will really allow you to push them out by hand?
Logged

Offline beelsamin

  • Enthusiast
  • **
  • Posts: 199
Re: Sleeves
« Reply #4 on: December 22, 2007, 02:12:49 PM »
It's that easy?
I would have thought a press would be needed...hmmm guess I'll send the wife out to shop for 3 or 4 hours,then I can use the shop...er...kitchen oven :)
Thanks
Logged
1977 Suzuki GT750
1972 Honda CB750 K2
1978 Honda CB550K

Offline Big Jay

  • Expert
  • ****
  • Posts: 1,252
    • CBRzone
Re: Sleeves
« Reply #5 on: December 22, 2007, 03:34:57 PM »
Quote from: beelsamin on December 22, 2007, 02:12:49 PM
It's that easy?
I would have thought a press would be needed...hmmm guess I'll send the wife out to shop for 3 or 4 hours,then I can use the shop...er...kitchen oven :)
Thanks

You then have to surface the block.  Gonna need a Bridgport in the kitchen too, to handle that part.

When the new sleeves are installed and the block has cooled off, you need t6o press the sleeves on down. They will drop .004 - .005". If you go ahead and surface it without doing this, they run the risk of dropping when the motor heats up.

Jay
Logged
Pages: [1]   Go Up
« previous next »