« previous next »
Pages: [1]   Go Down

Author Topic: Mating upper & lower halfs of different bikes  (Read 1087 times)

0 Members and 1 Guest are viewing this topic.

Offline Sgt Wonderful

  • Full Member
  • *
  • Posts: 23
Mating upper & lower halfs of different bikes
« on: November 22, 2008, 04:05:01 PM »
Question:
I'm assembling a 1971 CB 750. Upon close examanation I notice the crankcase is cracked. I obtained another crankcase  (lower half) from another bike, and want to mate it with my upper. Will I have a problem when it comes to getting main bearing to fit?
Any help or constructive comments will be appreciated.
Thanks,
John
« Last Edit: November 22, 2008, 06:12:35 PM by Sgt Wonderful »
Logged

Offline FunJimmy

  • Who you calling
  • Old Timer
  • ******
  • Posts: 3,798
  • Vancouver
Re: Mating upper & lower halfs of different bikes
« Reply #1 on: November 22, 2008, 09:02:23 PM »
John

I may be wrong, but don’t they line bore the crank journals as a matched pair?
I’d try to get the other case half from the same engine if it where me.

Jimmy
Logged
You never see a motorcycle parked outside of a psychiatrist's office!

CB550 Cafe Interceptor a Gentlemans Roadster
http://forums.sohc4.net/index.php?topic=27159.0

Offline bill440cars

  • Feeling More & More,
  • Really Old Timer ...
  • *******
  • Posts: 12,351
  • Tryin' To Slow Down "Time"!
Re: Mating upper & lower halfs of different bikes
« Reply #2 on: November 23, 2008, 09:22:32 AM »
Quote from: FunJimmy on November 22, 2008, 09:02:23 PM
John

I may be wrong, but don’t they line bore the crank journals as a matched pair?
I’d try to get the other case half from the same engine if it where me.

Jimmy

        I would be thinking that you are right Jimmy. Since the bearings appear to set in each case half, no way would I consider using another case half, without getting it checked by a machine shop and  maybe you could get it mated up. I think you might get by with it if it was a 2 cylinder if they have another piece that actually holds the crank in the upper case half. Far as I know, anyway. ;)

                                Take care, Bill ;)

     
Logged
Member # 1969
PRAYERS ALWAYS FOR: Bre, Jeff & Virginia, Bear, Trevor & Brianna ( Close Friend's Daughter)
"Because HE lives, I can Face Tomorrow"                  
 You CAN Teach An Old Dog New Tricks, Just Takes A Little Bit Longer & A Lot More Patience!! 
             
Main Rides: '02 Durango, '71 Swinger & Dad's '93
                  Dakota LE 4x4 '66 CB77 & '72 SL350K2
Watch What You Step Into, It Could  End Up A Mess!

Offline boatsdickson

  • Hot Shot
  • ***
  • Posts: 673
  • 1978 836 K8
Re: Mating upper & lower halfs of different bikes
« Reply #3 on: November 23, 2008, 04:43:01 PM »
Quote
I may be wrong, but don’t they line bore the crank journals as a matched pair?
I’d try to get the other case half from the same engine if it where me.

Ive heard the same as for matchin and grinding the halves as a set. I currently have the same issue with a bad lower case but a good upper. Also a problem might come about trying to match different halves with the different K models.

By the way, anyone have a good K8 I could buy?  :)

Good luck Sarge...
Logged
"No. We're all our own prisons, we are each all our own wardens and we do our own time. I can't judge anyone else. What other people do is not really my affair unless they approach me with it. Prison's in your mind. Can't you see I'm free"?  Testimonial of Charles Manson

Offline Sgt Wonderful

  • Full Member
  • *
  • Posts: 23
Re: Mating upper & lower halfs of different bikes
« Reply #4 on: November 23, 2008, 04:45:14 PM »
Thanks guys, Thats what I figured you all would say. I'll get the other half. I started to think about it when I was trying to figure out what kind of bearings to get. I looked on the crank and got the letters and looked at the case and got the letters and started to figure it out. I plan on putting in standard size bearings.  Mains one, two four and five were green, number three was yellow. Now all I have to do is find a place that sells them. ANY SUGGESTIONS..
Logged

Offline boatsdickson

  • Hot Shot
  • ***
  • Posts: 673
  • 1978 836 K8
Re: Mating upper & lower halfs of different bikes
« Reply #5 on: November 23, 2008, 04:51:01 PM »
http://forums.sohc4.net/index.php?topic=743.msg4704#msg4704

Since your posts are low, its hard to tell if youve lurked a while or not. Have you looked at the above topic yet? Should be alot of cross reference info there.
Logged
"No. We're all our own prisons, we are each all our own wardens and we do our own time. I can't judge anyone else. What other people do is not really my affair unless they approach me with it. Prison's in your mind. Can't you see I'm free"?  Testimonial of Charles Manson

Offline Sgt Wonderful

  • Full Member
  • *
  • Posts: 23
Re: Mating upper & lower halfs of different bikes
« Reply #6 on: November 23, 2008, 07:46:16 PM »
I'M BRAND NEW HERE, JUST BEEN HERE A FEW DAYS NOW.
Logged

Offline 754

  • Really Old Timer ...
  • *******
  • Posts: 29,050
Re: Mating upper & lower halfs of different bikes
« Reply #7 on: November 23, 2008, 08:48:59 PM »
Boat, do you mean cases or whole bike??

I might be able to sell a set of 78F cases, but I am way up in Canada.
Logged
Maker of the WELDLESS 750 Frame Kit
dodogas99@gmail.com
Kelowna B.C.       Canada

My next bike will be a ..ANFOB.....

It's All part of the ADVENTURE...

73 836cc.. Green, had it for 3 decades!!
Lost quite a few CB 750's along the way

Offline boatsdickson

  • Hot Shot
  • ***
  • Posts: 673
  • 1978 836 K8
Re: Mating upper & lower halfs of different bikes
« Reply #8 on: November 24, 2008, 06:32:49 AM »
Nope. Just needing the cases of a k8. Welcome to the group.
Logged
"No. We're all our own prisons, we are each all our own wardens and we do our own time. I can't judge anyone else. What other people do is not really my affair unless they approach me with it. Prison's in your mind. Can't you see I'm free"?  Testimonial of Charles Manson

Offline Sgt Wonderful

  • Full Member
  • *
  • Posts: 23
Re: Mating upper & lower halfs of different bikes
« Reply #9 on: November 24, 2008, 04:15:45 PM »
I've got a cracked one you can have.
Logged

Offline boatsdickson

  • Hot Shot
  • ***
  • Posts: 673
  • 1978 836 K8
Re: Mating upper & lower halfs of different bikes
« Reply #10 on: November 25, 2008, 05:07:24 AM »
 ;D ;D ;D ;D ;D

Ive also got an f2 case thats cracked you can have. Merry christmas.  ;D ;D
Logged
"No. We're all our own prisons, we are each all our own wardens and we do our own time. I can't judge anyone else. What other people do is not really my affair unless they approach me with it. Prison's in your mind. Can't you see I'm free"?  Testimonial of Charles Manson

Offline Sgt Wonderful

  • Full Member
  • *
  • Posts: 23
Re: Mating upper & lower halfs of different bikes
« Reply #11 on: December 02, 2008, 09:11:31 AM »
Got my crack welded. I'm lucky, my son is an Aluminum welder of the highest caliber. He Tig welded it and it almost looks like it came that way. He's a layed off auto worker with lots of time on his hands for my little projects. It was cracked where the drive sproket was. Looked like a chain came off and cracked the case.
Logged
Pages: [1]   Go Up
« previous next »