Author Topic: Bleeding brakes  (Read 4045 times)

0 Members and 1 Guest are viewing this topic.

Offline Johnny5

  • Master
  • *****
  • Posts: 1,593
    • CB350F build thread
Bleeding brakes
« on: February 19, 2009, 07:09:43 PM »
I know this has been covered a hundred times and used the search function but couldnt find my answer.

I have a 77 CB750k. I took apart the brake caliper, cleaned the piston and cylinder, used silicone grease and reinstalled everything. The fluid was completely emptied obviously so I buttoned everything up and filling the master cylinder with fluid and I cant get the system to prime. Only getting small bubbles from the master cylinder. I tried pumping with the bleed nipple open and closed. Right now, I have the brake lever held depressed with a strap hoping fluid will eventually leak into the system.

Any tips on how to prime the system? Or do I just keep pumping?

Thanks,
www.kerosenecycles.com
1971 CB350
1973 CB350F
2006 Harley Springer Classic

Offline Bob Wessner

  • "Carbs Suck!"
  • Really Old Timer ...
  • *******
  • Posts: 10,079
Re: Bleeding brakes
« Reply #1 on: February 19, 2009, 07:13:12 PM »
We'll all be someone else's PO some day.

Offline Johnny5

  • Master
  • *****
  • Posts: 1,593
    • CB350F build thread
Re: Bleeding brakes
« Reply #2 on: February 19, 2009, 07:18:52 PM »
Man, didnt even see the FAQ. Feel silly.

Thanks!
www.kerosenecycles.com
1971 CB350
1973 CB350F
2006 Harley Springer Classic

Offline Hush

  • Finally they realise that I am an
  • Really Old Timer ...
  • *******
  • Posts: 6,761
  • "Lady, I've heard it all before"!
Re: Bleeding brakes
« Reply #3 on: February 19, 2009, 08:12:23 PM »
I have a new word for you....MICROBUBBLES, these little suckers will keep bubbling up for days but eventually they stop and your brakes work again.
My advice (after of course you check out the FAQ;s) is get it as good as you can then leave it and have a beer, go back to it and hour later and squeeze the lever some more...then go have another beer.....continue this until you are too drunk to ride anyway or the brakes stop bubbling.
It took me 3 days to remove them little buggers from my sysytem...........Hush.
I think the thing I most like about motorcycling is the speed at which my brain must process information at to avoid the numb skulls who are eating pies, playing the ukulele, applying make-up etc in the comfort of their airconditioned armchairs as they make random attempts to kill me!!!!!!!

Online bryanj

  • Really Old Timer ...
  • *******
  • Posts: 14,187
  • CB500 Number 1000036
Re: Bleeding brakes
« Reply #4 on: February 19, 2009, 08:18:18 PM »
First WEAR GLOVES and cover everything

Remover banjo bolt and pipe from master a put gloved finger over outlet

pull in lever and whilst holding in lift finger from outlet and replace

let go lever and pull in and hold again lift and replace gloved finger

keep repeating until master cylinder builds pressure and fluid squirts out under finger (thats why you cover everything!!!)

whilst holding in lever reconnect pipe with banjo bolt and now bleed via bleed nipple
Semi Geriatric ex-Honda mechanic and MOT tester (UK version of annual inspection). Garage full of "projects" mostly 500/4 from pre 73 (no road tax in UK).

Remember "Its always in the last place you look" COURSE IT IS YOU STOP LOOKIN THEN!

Offline Johnny5

  • Master
  • *****
  • Posts: 1,593
    • CB350F build thread
Re: Bleeding brakes
« Reply #5 on: February 20, 2009, 04:45:22 AM »
I wont be riding the bike anytime soon as it doesnt have the engine in and it's 20 degrees outside...and the bike is in the basement...and..

Thanks for all the suggestions. I got most of the bleeding done last night. I'll continue to bleed for a couple more days and make sure all those bubbles are out. Im using a clear hose from the bleed nipple so I can see the bubbles.
www.kerosenecycles.com
1971 CB350
1973 CB350F
2006 Harley Springer Classic