Author Topic: Billet blocks....who will pay...pics added 9/7/09...10/24....2/10 (Read 192033 times)

mick7504 · « **Reply #550 on:** September 11, 2011, 04:36:49 PM »

Quote from: BLUE71TURBO on September 09, 2011, 09:07:19 AM

Mike or anyone else, i have been wondering what is the piston to cylinder wall clearance with Nikisal coated bores ??

Hey Blue
Mike had the clearance set at .0012 to suit the 72mm MTC pistons that will be going in.
Mick

BLUE71TURBO · « **Reply #551 on:** September 11, 2011, 05:14:10 PM »

Mick, thanks for the info........

dragracer · « **Reply #552 on:** November 20, 2011, 08:36:32 PM »

Mike, since there is an absence of space robbing sleeves, exactly how large a bore can you get out of one of your virgin blocks??? I would think 72mm is not the limit but correct me if i'm wrong. Or perhaps i should have read the entire thread because i'm sure someone has already asked that question.

Tintop · « **Reply #553 on:** November 21, 2011, 05:14:49 PM »

The pistons for mine are 73.25 if I remember correctly.

MRieck · « **Reply #554 on:** November 22, 2011, 06:48:34 AM »

Quote from: Tintop on November 21, 2011, 05:14:49 PM

The pistons for mine are 73.25 if I remember correctly.

TT...they are 71.25. You could put a 74mm piston in there I'd think off hand. That and a 5 mm stroke would bring you to what......... almost 1200cc or so? That would break all sorts of sh!t in a hurry.

Leino · « **Reply #555 on:** November 22, 2011, 06:58:16 AM »

Quote from: MRieck on November 22, 2011, 06:48:34 AM

Quote from: Tintop on November 21, 2011, 05:14:49 PM
The pistons for mine are 73.25 if I remember correctly.
TT...they are 71.25. You could put a 74mm piston in there I'd think off hand. That and a 5 mm stroke would bring you to what......... almost 1200cc or so? That would break all sorts of sh!t in a hurry.

1170cc

Tintop · « **Reply #556 on:** November 23, 2011, 07:36:38 PM »

Quote from: MRieck on November 22, 2011, 06:48:34 AM

Quote from: Tintop on November 21, 2011, 05:14:49 PM
The pistons for mine are 73.25 if I remember correctly.
TT...they are 71.25. You could put a 74mm piston in there I'd think off hand. That and a 5 mm stroke would bring you to what......... almost 1200cc or so? That would break all sorts of sh!t in a hurry.

Apologies, your right Mike.

dragracer · « **Reply #557 on:** January 09, 2012, 04:42:02 PM »

Quote from: MRieck on November 22, 2011, 06:48:34 AM

Quote from: Tintop on November 21, 2011, 05:14:49 PM
The pistons for mine are 73.25 if I remember correctly.
TT...they are 71.25. You could put a 74mm piston in there I'd think off hand. That and a 5 mm stroke would bring you to what......... almost 1200cc or so? That would break all sorts of sh!t in a hurry.

Who makes a 74mm piston with the correct wrist pin diameter, valve pocket position and dome height?? I wouldn't mind breaking something just to see how quick i can make my bike run-lol. Well, there's always nitrous- it'll make a short man feel like a giant with just a little shot.

Bill/BentON Racing · « **Reply #558 on:** January 09, 2012, 05:55:33 PM »

+++++++++++++++++1!!!!!!!!!!!!!!!!!!!!!!!!! ;)It would be FUN!!!!

Bill

Jerry Rxman Griffin aka MuthaF'er · « **Reply #559 on:** January 09, 2012, 09:17:10 PM »

Quote from: dragracer on January 09, 2012, 04:42:02 PM

Quote from: MRieck on November 22, 2011, 06:48:34 AM
Quote from: Tintop on November 21, 2011, 05:14:49 PM
The pistons for mine are 73.25 if I remember correctly.
TT...they are 71.25. You could put a 74mm piston in there I'd think off hand. That and a 5 mm stroke would bring you to what......... almost 1200cc or so? That would break all sorts of sh!t in a hurry.

Who makes a 74mm piston with the correct wrist pin diameter, valve pocket position and dome height?? I wouldn't mind breaking something just to see how quick i can make my bike run-lol. Well, there's always nitrous- it'll make a short man feel like a giant with just a little shot.

Don't know who makes them but I have a 73.75mm NOS set with the same pin diameter

faitly flat tops too.

dragracer · « **Reply #560 on:** January 09, 2012, 09:33:13 PM »

Quote from: Jerry Rxman Griffin on January 09, 2012, 09:17:10 PM

Quote from: dragracer on January 09, 2012, 04:42:02 PM
Quote from: MRieck on November 22, 2011, 06:48:34 AM
Quote from: Tintop on November 21, 2011, 05:14:49 PM
The pistons for mine are 73.25 if I remember correctly.
TT...they are 71.25. You could put a 74mm piston in there I'd think off hand. That and a 5 mm stroke would bring you to what......... almost 1200cc or so? That would break all sorts of sh!t in a hurry.

Who makes a 74mm piston with the correct wrist pin diameter, valve pocket position and dome height?? I wouldn't mind breaking something just to see how quick i can make my bike run-lol. Well, there's always nitrous- it'll make a short man feel like a giant with just a little shot.

Don't know who makes them but I have a 73.75mm NOS set with the same pin diameter faitly flat tops too.

Noooooo, don't make me do it!!!!!! Lol.

Jerry Rxman Griffin aka MuthaF'er · « **Reply #561 on:** January 09, 2012, 09:46:29 PM »

Sorry, I think they are only 73.25mm

stock 736 61mm, 812 64mm, 890 67mm, and the BMF. Guess I should've gotten a picture with the 1000's before I installed the 67mm pistons

Retro Rocket · « **Reply #562 on:** January 09, 2012, 09:49:51 PM »

Quote

Noooooo, don't make me do it!!!!!! Lol.

Go on, you know you want too....

Tintop · « **Reply #563 on:** January 10, 2012, 05:45:13 AM »

If I remember correctly, they were 73.25's that came with my billet barrel from Mike.

Would make it a 1080.

Leino · « **Reply #564 on:** January 10, 2012, 11:48:35 PM »

Quote from: Tintop on January 10, 2012, 05:45:13 AM

If I remember correctly, they were 73.25's that came with my billet barrel from Mike. Would make it a 1080.

73.25's / stock stroke = 1061.95cc

scunny · « **Reply #565 on:** January 10, 2012, 11:59:35 PM »

M3 racing have 75,76 and 77 mm pistons for thumpers. I can't remember the wrist pin diameter tho.

Tintop · « **Reply #566 on:** January 11, 2012, 12:05:53 PM »

Quote from: Leino on January 10, 2012, 11:48:35 PM

Quote from: Tintop on January 10, 2012, 05:45:13 AM
If I remember correctly, they were 73.25's that came with my billet barrel from Mike. Would make it a 1080.
73.25's / stock stroke = 1061.95cc

OK, and a CB750 is 750cc's.

Leino · « **Reply #567 on:** January 11, 2012, 11:47:18 PM »

Quote from: Tintop on January 11, 2012, 12:05:53 PM

OK, and a CB750 is 750cc's.

No offence intended, I'm just weird in the way that I prefer real life cc's over salesman's imaginary ones

Tintop · « **Reply #568 on:** January 12, 2012, 10:26:45 AM »

Quote from: Leino on January 11, 2012, 11:47:18 PM

Quote from: Tintop on January 11, 2012, 12:05:53 PM
OK, and a CB750 is 750cc's.
No offence intended, I'm just weird in the way that I prefer real life cc's over salesman's imaginary ones

None taken Leino.

gsb · « **Reply #569 on:** January 12, 2012, 10:57:59 AM »

Hi!
I would like to know what cost Billet block with shiping to EU ? For me 900 to 950 ccm were enough ,
Thanks gsb

MRieck · « **Reply #570 on:** January 13, 2012, 07:48:00 AM »

Quote from: gsb on January 12, 2012, 10:57:59 AM

Hi!
I would like to know what cost Billet block with shiping to EU ? For me 900 to 950 ccm were enough ,
Thanks gsb

email sent

Danno · « **Reply #571 on:** February 10, 2012, 01:57:28 AM »

mike that is the most beautiful piece of machine work I have ever seen absolutely gorgeous

Retro Rocket · « **Reply #572 on:** February 10, 2012, 04:12:06 AM »

Quote from: Danno on February 10, 2012, 01:57:28 AM

mike that is the most beautiful piece of machine work I have ever seen absolutely gorgeous

You should see them in person...

MRieck · « **Reply #573 on:** February 10, 2012, 07:24:06 AM »

Quote from: Danno on February 10, 2012, 01:57:28 AM

mike that is the most beautiful piece of machine work I have ever seen absolutely gorgeous

Thanks! I have plenty in stock!

bert96 · « **Reply #574 on:** April 20, 2012, 04:19:49 PM »

I'm a little bit affraid of asking the price of this billet block....but i need to know,sorry if you already post this information MRieck

Bert

News:

Author Topic: Billet blocks....who will pay...pics added 9/7/09...10/24....2/10 (Read 192033 times)