« previous next »
Pages: [1]   Go Down

Author Topic: DOES ANYBODY KNOW HOW TO CONTACT A.R.D. ENGINEERING ?  (Read 2005 times)

0 Members and 1 Guest are viewing this topic.

Offline BLUE71TURBO

  • Master
  • *****
  • Posts: 1,849
DOES ANYBODY KNOW HOW TO CONTACT A.R.D. ENGINEERING ?
« on: June 12, 2009, 09:40:15 AM »
The last i heard AL was in SANTA FE SPRINGS. Does anyone know how to get a hold of him ?
Logged
Remember; Before you can be old and wise, you must first be young and stupid !

Offline Bob Wessner

  • "Carbs Suck!"
  • Really Old Timer ...
  • *******
  • Posts: 10,079
Re: DOES ANYBODY KNOW HOW TO CONTACT A.R.D. ENGINEERING ?
« Reply #1 on: June 12, 2009, 09:45:50 AM »
Logged
We'll all be someone else's PO some day.

Offline BLUE71TURBO

  • Master
  • *****
  • Posts: 1,849
Re: DOES ANYBODY KNOW HOW TO CONTACT A.R.D. ENGINEERING ?
« Reply #2 on: June 12, 2009, 10:09:08 AM »
NOPE !    A.R.D. ENGINEERING made belt drive magnetos. They used to be located in SANTA FE SPRINGS.
Logged
Remember; Before you can be old and wise, you must first be young and stupid !

Offline ludo410

  • Full Member
  • *
  • Posts: 17
Re: DOES ANYBODY KNOW HOW TO CONTACT A.R.D. ENGINEERING ?
« Reply #3 on: June 12, 2009, 10:56:43 AM »
try Cycle-X i know they have one or two of his ARD electronic ignitions they may have his new contact info or at least be able to answer your question
         http://www.cyclexchange.net/Engine%20Parts%20Page.htm
Logged

Offline Really?

  • I've come to the conclusion that I AM a
  • Really Old Timer ...
  • *******
  • Posts: 5,276
Re: DOES ANYBODY KNOW HOW TO CONTACT A.R.D. ENGINEERING ?
« Reply #4 on: June 12, 2009, 11:00:21 AM »
Logged
I don't have a motorcycle, sold it ('85 Yamaha Venture Royale).  Haven't had a CB750 for over 40 years.

The Wife's Bike - 750K5
The Kid's Bike - 750K3

Offline Turbogrimace

  • Hot Shot
  • ***
  • Posts: 387
    • Draft Cycle Works
Re: DOES ANYBODY KNOW HOW TO CONTACT A.R.D. ENGINEERING ?
« Reply #5 on: June 12, 2009, 12:10:01 PM »
I dont think Ken has any contact info for ARD.  He has a few of their mags, but those were not directly from ARD.  What is it that you are looking for?
Logged

Offline BLUE71TURBO

  • Master
  • *****
  • Posts: 1,849
Re: DOES ANYBODY KNOW HOW TO CONTACT A.R.D. ENGINEERING ?
« Reply #6 on: June 13, 2009, 08:30:06 AM »
I just wanted to pickup some extra parts. My A.R.D. mag is the CDI unit. It is basically brand new, only 2,000 miles of
use on it. I located another unit but it is missing the rotor, cap, coil, and lower pulley. I'm wanting to build a super-
charged cb750 with a big block and a magneto. I might just try to find an old RC engineering angle drive for a joe hunt
magneto like that is used in vw drag motors.
Logged
Remember; Before you can be old and wise, you must first be young and stupid !

Offline Turbogrimace

  • Hot Shot
  • ***
  • Posts: 387
    • Draft Cycle Works
Re: DOES ANYBODY KNOW HOW TO CONTACT A.R.D. ENGINEERING ?
« Reply #7 on: June 15, 2009, 06:53:38 AM »
www.magnetoparts.com

This guy has everything you need.  The lower pulley is just half the size of the upper pulley for a 2:1 ratio.  Get a new one cut to fit the shaft.  I dont have mine in front of me, but Browning still makes that gearbelt pulley.  Then it just needs to be bored to fit the lower shaft.
Logged

Offline Sam Green Racing

  • Really Old Timer ...
  • *******
  • Posts: 16,068
  • I REALLY? hate black rims.
Re: DOES ANYBODY KNOW HOW TO CONTACT A.R.D. ENGINEERING ?
« Reply #8 on: June 15, 2009, 05:56:59 PM »
25 pages in this thread, you might find it here.

Sam. ;)

http://forums.sohc4.net/index.php?topic=14994.0
Logged
C95 sprint bike.
CB95 hybrid race bike
CB95 race bike
CB92
RS 175. sprint/land speed bike
JMR Racing CB750A street ET drag bike
Pages: [1]   Go Up
« previous next »