« previous next »
Pages: [1]   Go Down

Author Topic: Rotor hitting stator  (Read 1415 times)

0 Members and 1 Guest are viewing this topic.

Offline grumburg

  • Expert
  • ****
  • Posts: 944
  • 74550, 76400F, 72 750 67S90, 68CL90, 65 s65 66 x6
Rotor hitting stator
« on: March 22, 2010, 05:36:05 AM »
Hoped to finish my S90 project yesterday, but when I kicked it over, there was a clatter. Removed the left cover and the rotor is touching the stator contacts. Front of vanes 180 degrees apart. Can see previous wear marks. Any ideas?  ???
Logged
Fonda Honda

Offline Sam Green Racing

  • Really Old Timer ...
  • *******
  • Posts: 16,068
  • I REALLY? hate black rims.
Re: Rotor hitting stator
« Reply #1 on: March 22, 2010, 06:00:35 AM »
End of crank bent :(

Sam.
Logged
C95 sprint bike.
CB95 hybrid race bike
CB95 race bike
CB92
RS 175. sprint/land speed bike
JMR Racing CB750A street ET drag bike

Offline grumburg

  • Expert
  • ****
  • Posts: 944
  • 74550, 76400F, 72 750 67S90, 68CL90, 65 s65 66 x6
Re: Rotor hitting stator
« Reply #2 on: March 22, 2010, 06:35:48 AM »
Dial indicator shows 0 runout at crank
Logged
Fonda Honda

Offline Sam Green Racing

  • Really Old Timer ...
  • *******
  • Posts: 16,068
  • I REALLY? hate black rims.
Re: Rotor hitting stator
« Reply #3 on: March 22, 2010, 06:43:44 AM »
Seeing as the rotor is on a tapered shaft, I wouldn't think it could not go on correct.
Is the stator mounted correct, might it have been damaged when you aquired the bike?

Sam. ;)
Logged
C95 sprint bike.
CB95 hybrid race bike
CB95 race bike
CB92
RS 175. sprint/land speed bike
JMR Racing CB750A street ET drag bike

Offline bryanj

  • Really Old Timer ...
  • *******
  • Posts: 14,031
  • CB500 Number 1000036
Re: Rotor hitting stator
« Reply #4 on: March 22, 2010, 08:06:15 AM »
Locating dowel (s) missing?
Logged
Semi Geriatric ex-Honda mechanic and MOT tester (UK version of annual inspection). Garage full of "projects" mostly 500/4 from pre 73 (no road tax in UK).

Remember "Its always in the last place you look" COURSE IT IS YOU STOP LOOKIN THEN!

Offline TomC

  • Hot Shot
  • ***
  • Posts: 325
Re: Rotor hitting stator
« Reply #5 on: March 22, 2010, 03:03:41 PM »
Hi BryanJ & Group
     There is no locating dowel (s). The dowel on the Super 90 stator is a stop for the cam chain guide roller. The stator is located by the fit of the outer diameter of the stator into the left crankcase.
Quote from: bryanj on March 22, 2010, 08:06:15 AM
Locating dowel (s) missing?
     If the rotor is spinning true I would check that the stator is seated properly and not bent.
     TomC in Ohio
Logged
TomC in Ohio
76 CB750 F1 Daily Rider
76 CB550 stalled project
76 CB400F Injured Reserve
Pages: [1]   Go Up
« previous next »