« previous next »
Pages: [1]   Go Down

Author Topic: why does the float still stick!  (Read 4081 times)

0 Members and 1 Guest are viewing this topic.

Offline heffay

  • Really Old Timer ...
  • *******
  • Posts: 7,874
why does the float still stick!
« on: February 08, 2006, 03:10:12 PM »
 installed new carb kits in the ex500carbs (let's just pretend they are sohc4 for now) 

i thought i had it peg'd as the carb that was sticking had a bum float pin (you know the thingy that attaches to the float and plugs the fuelflow coming into the carb.  it has a spring loaded cylinder that helps to push the stopper down in the hole.  that spring loaded doodad was stuck. 

so, new float pins later and it's still letting gas into the carb... my only thought is it's not making a seal.  is there something else i'm missing?
Logged
Today: '73 cb350f, '96 Ducati 900 Supersport
Past Rides: '72 tc125, '94 cbr600f2, '76 rd400, '89 ex500, '93 KTM-125exc, '92 zx7r, '93 Banshee, '83 ATC250R, 77/75 cb400f

Offline heffay

  • Really Old Timer ...
  • *******
  • Posts: 7,874
Re: why does the float still stick!
« Reply #1 on: February 08, 2006, 03:19:41 PM »
yes... i'm sure the float is not working properly as gas runs out of the carbs when the fuel is on and the bike runs with the gas off...

yay! for it finally running at least tho.  right?
Logged
Today: '73 cb350f, '96 Ducati 900 Supersport
Past Rides: '72 tc125, '94 cbr600f2, '76 rd400, '89 ex500, '93 KTM-125exc, '92 zx7r, '93 Banshee, '83 ATC250R, 77/75 cb400f

Offline Bob Wessner

  • "Carbs Suck!"
  • Really Old Timer ...
  • *******
  • Posts: 10,079
Re: why does the float still stick!
« Reply #2 on: February 08, 2006, 03:30:45 PM »
Is it running out of all, or multiple carbs? I could see perhaps on of the float valves not seating if the seat is chewed up, or something. Are the float heights correct? Just thoughts...
Logged
We'll all be someone else's PO some day.

Offline 8 Track

  • Hot Shot
  • ***
  • Posts: 449
  • 1976 cb750
Re: why does the float still stick!
« Reply #3 on: February 08, 2006, 04:03:49 PM »
Is the float sinking?  Maybe the needle is hanging up in its travel up and down.  Float level too high and it will go out the overflow before the float shuts off the gas.  (I have a feeling you know that because you know your way around bikes).
Logged
My dog loves me for the person I try to be.  Either that or he's hungry.

Offline heffay

  • Really Old Timer ...
  • *******
  • Posts: 7,874
Re: why does the float still stick!
« Reply #4 on: February 08, 2006, 04:38:32 PM »
ok... float height was set when i put the carbs in the bike... the same carb did stick on me before i got height set but, the tang was bent way to far and that was the culprit.

got the float height set... even shook them around to mimic riding... they did not overflow. 

the seat that the pin sits in seems to look ok.

there doesn't seem to be any gas inside the floats that i've noticed. 

will get some pics soon... cleaned it up, new race pipes from Brazil, new batt, plugs, AND CARB KITS THAT AREN'T WORKING!
« Last Edit: February 08, 2006, 06:05:33 PM by heffay »
Logged
Today: '73 cb350f, '96 Ducati 900 Supersport
Past Rides: '72 tc125, '94 cbr600f2, '76 rd400, '89 ex500, '93 KTM-125exc, '92 zx7r, '93 Banshee, '83 ATC250R, 77/75 cb400f

Offline 6adan

  • Hot Shot
  • ***
  • Posts: 421
Re: why does the float still stick!
« Reply #5 on: February 08, 2006, 06:57:05 PM »
I had a crack in a overflow tube on my bike, thought it was a stuck float, you might want to check this. Dannie
Logged
1970 CB750 JDM,1975 GL1000, 1979 GL1000, 1979 CBX, 1995 GL1500, 2000 GL1500CT Valkyrie, 2008 GL1800 Trike.

Offline heffay

  • Really Old Timer ...
  • *******
  • Posts: 7,874
Re: why does the float still stick!
« Reply #6 on: February 09, 2006, 10:16:41 AM »
like i said... pretty sure its the right side carb float sticking.  it's not instant either... every time it's stuck, it takes a few minutes to occur  then it just continues to overflow.

anyone have experience taking in or out pressed fittings like a jet needle seat?  but, perhaps the needle is hanging up in its movement... experience remedying that?
Logged
Today: '73 cb350f, '96 Ducati 900 Supersport
Past Rides: '72 tc125, '94 cbr600f2, '76 rd400, '89 ex500, '93 KTM-125exc, '92 zx7r, '93 Banshee, '83 ATC250R, 77/75 cb400f

Offline TwoTired

  • Really Old Timer ...
  • *******
  • Posts: 21,805
Re: why does the float still stick!
« Reply #7 on: February 09, 2006, 11:27:42 AM »
Does it make a difference if the bike is on the side stand or center stand?

Does it leak while driving around? or just stationary.  I'm not sure what your carbs look like inside.  But check where the float pivots meet the posts where the pins are.  Are they smooth?  Any drag when you side load the float?

Having said that, Are your float valves rubber tipped or metal.  Rubber is a bit more forgiving of seat imperfections.  Metal tipped ones, less so.  Either the seat is not well matched, or perhaps the vibration will eventually wear in the mating surface.

Good luck!

Logged
Lloyd... (SOHC4 #11 Original Mail List)
72 500, 74 550, 75 550K, 75 550F, 76 550F, 77 550F X2, 78 550K, 77 750F X2, 78 750F, 79CX500, 85 700SC, GL1100

Those that learn from history are doomed to repeat it by those that don't learn from history.

Offline Magpie

  • Old Timer
  • ******
  • Posts: 3,298
Re: why does the float still stick!
« Reply #8 on: February 09, 2006, 12:33:00 PM »
Ditto on Dannie's reply. I couldn't figure out why the gas kept coming out the overflow tube until a wise, old mechanic said to take the float bowl off, plug one end of the tube with my finger and try to blow throught the other end. Sure enough the tube was cracked.
Easy check, simple solution. Hope this helps.
Cliff.
Logged

Offline heffay

  • Really Old Timer ...
  • *******
  • Posts: 7,874
Re: why does the float still stick!
« Reply #9 on: February 15, 2006, 01:26:08 PM »
or... since it's been snowy outside, i have nothing to do but homework and internet, and spending money is fun... i'll just buy a new carb bank off ebay  ;D  46usd including shipping... paid 40 for the carb kits... interesting.  we'll see what happens  ;)

the "ducktacktylpuss" will run!
but for now... it seems to be the "sucktactylpuss"!
Logged
Today: '73 cb350f, '96 Ducati 900 Supersport
Past Rides: '72 tc125, '94 cbr600f2, '76 rd400, '89 ex500, '93 KTM-125exc, '92 zx7r, '93 Banshee, '83 ATC250R, 77/75 cb400f

Offline heffay

  • Really Old Timer ...
  • *******
  • Posts: 7,874
Re: why does the float still stick!
« Reply #10 on: February 15, 2006, 01:33:53 PM »
check out the shiny new bits tho!   ;D

hard to believe that elizabeth will be able to be in the "rusted nuts" cuz this bike is very soon to be 20 years old... the first year of production and they are still being produced as the ninja500 probably still the same boring old gpz500 for those of you in the "different" know.
Logged
Today: '73 cb350f, '96 Ducati 900 Supersport
Past Rides: '72 tc125, '94 cbr600f2, '76 rd400, '89 ex500, '93 KTM-125exc, '92 zx7r, '93 Banshee, '83 ATC250R, 77/75 cb400f

Offline Gordon

  • Global Moderator
  • Really Old Timer ...
  • *****
  • Posts: 12,114
  • 750K1, 550K2
Re: why does the float still stick!
« Reply #11 on: February 16, 2006, 10:36:59 AM »
Sweet, a new Rusted Nut!! ;D ;D
Logged

Offline heffay

  • Really Old Timer ...
  • *******
  • Posts: 7,874
Re: why does the float still stick!
« Reply #12 on: February 24, 2006, 07:20:43 PM »
IT RUNS!!!!!!!!!!
only on choke... but, man... it runs!!!

Logged
Today: '73 cb350f, '96 Ducati 900 Supersport
Past Rides: '72 tc125, '94 cbr600f2, '76 rd400, '89 ex500, '93 KTM-125exc, '92 zx7r, '93 Banshee, '83 ATC250R, 77/75 cb400f
Pages: [1]   Go Up
« previous next »