« previous next »
Pages: 1 [2]   Go Down

Author Topic: Cold start issues  (Read 4159 times)

0 Members and 1 Guest are viewing this topic.

Offline lassenc

  • Hot Shot
  • ***
  • Posts: 266
Re: Cold start issues
« Reply #25 on: February 22, 2006, 01:36:07 PM »
Quote from: eldar, Master of the K8 Thunder! on February 22, 2006, 01:30:10 PM
Remove the airbox and look into your carbs. You will see the flaps. actuate the choke and watch them.

Okay, I assume I can just adjust the chokecabel? No additional parts need change?
Logged
How exactly do you teach abstinence though?
It's like beating a dead cow, it's fun, but it doens't really get you anywhere.

Offline n9viw

  • Enthusiast
  • **
  • Posts: 160
  • Floyd, '76 CB550k
Re: Cold start issues
« Reply #26 on: February 22, 2006, 02:25:02 PM »
You should be able to adjust the cable housing at the clamp above the carbs. Pull the choke cable out so the choke is on (ensure the friction lock at the top is tight). Check your flaps. If they're not 100% closed, there should be a phillips screw clamping the choke cable housing to the bracket above the carbs. Loosen that screw and pull slightly on the housing to close the flaps the rest of the way, then hold it there and tighten the screw. Next time you actuate your choke, it should close them 100%.
Logged
Nick

'76 Honda CB550k
'73 Honda CB750k

Offline lassenc

  • Hot Shot
  • ***
  • Posts: 266
Re: Cold start issues
« Reply #27 on: February 22, 2006, 10:41:39 PM »
I'll try that :)
Logged
How exactly do you teach abstinence though?
It's like beating a dead cow, it's fun, but it doens't really get you anywhere.

Offline lassenc

  • Hot Shot
  • ***
  • Posts: 266
Re: Cold start issues
« Reply #28 on: February 23, 2006, 06:26:57 AM »
Perfect battery mounted, with the same results as before.

It doens't even make a sound that it wants to go, I'm guessing the plugs.

Yesterday, I got it fired for like 5 seconds, and then it went dead.
Logged
How exactly do you teach abstinence though?
It's like beating a dead cow, it's fun, but it doens't really get you anywhere.

Offline lassenc

  • Hot Shot
  • ***
  • Posts: 266
Re: Cold start issues
« Reply #29 on: February 23, 2006, 10:54:14 AM »
Don't know if I was lucky or anything, but I got it started.

Took it for a 50 kilometer spin, only thing that I have to say, boy was great :)

Though I sometimes during accereleration from low rpm get a small "poof" from cylinder 4, it is no thread or is annoying or anything, it's just there :)
Logged
How exactly do you teach abstinence though?
It's like beating a dead cow, it's fun, but it doens't really get you anywhere.

Online dusterdude

  • Really Old Timer ...
  • *******
  • Posts: 8,489
Re: Cold start issues
« Reply #30 on: February 23, 2006, 11:53:45 AM »
sounds like a lean poof,check for air leaks around the carb boots.
Logged
mark
1972 k1 750
1949 fl panhead
1 1/2 gl1100 goldwings
1998 cbr600 f3

Offline lassenc

  • Hot Shot
  • ***
  • Posts: 266
Re: Cold start issues
« Reply #31 on: February 24, 2006, 01:41:14 AM »
Will do that!

Getting the new plugs today, and then we'll see, maybe it doesn't get fuel, afterall...
Logged
How exactly do you teach abstinence though?
It's like beating a dead cow, it's fun, but it doens't really get you anywhere.

Offline lassenc

  • Hot Shot
  • ***
  • Posts: 266
Re: Cold start issues
« Reply #32 on: February 24, 2006, 09:51:20 AM »
Got the plugs today.

And a 40 dollar plugtool-thing, cause I didn't have one in 18mm

And what do I see? I can't get that damn thing in the two center plugs :(
Logged
How exactly do you teach abstinence though?
It's like beating a dead cow, it's fun, but it doens't really get you anywhere.

supersport_CB400F

  • Guest
Re: Cold start issues
« Reply #33 on: February 24, 2006, 10:05:45 AM »
$10 spark plug socket (12mm) …works all the time  ;D
« Last Edit: February 24, 2006, 10:36:58 AM by _biffta_ »
Logged

Offline lassenc

  • Hot Shot
  • ***
  • Posts: 266
Re: Cold start issues
« Reply #34 on: February 27, 2006, 06:20:31 AM »
Just doesn't for me, can't get it all the way down to the plug.

I still have the problems by the way, I'll check the choke the next time.
Logged
How exactly do you teach abstinence though?
It's like beating a dead cow, it's fun, but it doens't really get you anywhere.

WiredForStereo

  • Guest
Re: Cold start issues
« Reply #35 on: February 27, 2006, 11:35:35 AM »
When I tore down my carbs, I discovered that the choke butterflys werent closing or opening completely.  I loosened all the screws holding on the butterfly's themselves and then retightened them.  They now open and close completely and easily.  I guess whoever rebuilt the carbs in the past tightened them so they were rubbing on the insides of the carbs and causing some friction.

About the plug puller, I found that when I had bought a regular long socket, I couldnt get at the two center plugs, I ended up having to grind around the wrench end of the socket to make it tapered and then it would fit down in there on an extension.
Logged

eldar

  • Guest
Re: Cold start issues
« Reply #36 on: February 27, 2006, 11:49:07 AM »
I got a plug socket from sears and it fit my 750 fine. I suppose the other bikes may be a bit smaller in clearance.
Logged

Offline lassenc

  • Hot Shot
  • ***
  • Posts: 266
Re: Cold start issues
« Reply #37 on: February 27, 2006, 01:43:29 PM »
Quote from: WiredForStereo on February 27, 2006, 11:35:35 AM
When I tore down my carbs, I discovered that the choke butterflys werent closing or opening completely.  I loosened all the screws holding on the butterfly's themselves and then retightened them.  They now open and close completely and easily.  I guess whoever rebuilt the carbs in the past tightened them so they were rubbing on the insides of the carbs and causing some friction.

About the plug puller, I found that when I had bought a regular long socket, I couldnt get at the two center plugs, I ended up having to grind around the wrench end of the socket to make it tapered and then it would fit down in there on an extension.

I don't feel like grinding down my 40 dollar tool :)

Could I have clogged carburettors?
Logged
How exactly do you teach abstinence though?
It's like beating a dead cow, it's fun, but it doens't really get you anywhere.

Offline KCs76Cafe

  • Hot Shot
  • ***
  • Posts: 358
  • Jackson Creek,NC..Deep in the stix of the TRIAD
Re: Cold start issues
« Reply #38 on: February 27, 2006, 03:35:22 PM »
Quote from: lassenc on February 27, 2006, 01:43:29 PM
Quote from: WiredForStereo on February 27, 2006, 11:35:35 AM


About the plug puller, I found that when I had bought a regular long socket, I couldnt get at the two center plugs, I ended up having to grind around the wrench end of the socket to make it tapered and then it would fit down in there on an extension.

I don't feel like grinding down my 40 dollar tool :)



Quote from: _biffta_ on February 24, 2006, 10:05:45 AM
$10 spark plug socket (12mm) …works all the time  ;D

Quote from: lassenc on February 24, 2006, 09:51:20 AM
Got the plugs today.

And a 40 dollar plugtool-thing, cause I didn't have one in 18mm



Jeez.....where yall getting those high dollar plug sockets?

I got my Craftsman 18mm plug socket at Sears for $3.99......and its guaranteed for life
Logged

Offline Gordon

  • Global Moderator
  • Really Old Timer ...
  • *****
  • Posts: 12,114
  • 750K1, 550K2
Re: Cold start issues
« Reply #39 on: February 27, 2006, 03:42:52 PM »
Same here.  The spark plug tool I use for the 750 wouldn't work for the 550, so I bought a cheap, thin-walled, deep, 18mm socket that fits perfectly.  I even use it for the 750 now because it's easier than what I had before. 
Logged

WiredForStereo

  • Guest
Re: Cold start issues
« Reply #40 on: February 27, 2006, 06:22:54 PM »
No no no no, dont grind on a $40 tool, grind on a $3 dollar tool (Napa) and make it as useful as a $40 tool. 
Logged

Offline lassenc

  • Hot Shot
  • ***
  • Posts: 266
Re: Cold start issues
« Reply #41 on: February 28, 2006, 02:25:41 AM »
Will do so :)
Logged
How exactly do you teach abstinence though?
It's like beating a dead cow, it's fun, but it doens't really get you anywhere.

Offline n9viw

  • Enthusiast
  • **
  • Posts: 160
  • Floyd, '76 CB550k
Re: Cold start issues
« Reply #42 on: February 28, 2006, 09:52:40 AM »
Ditto- got a thinwalled impact socket from Harbor Freight for $2, and ground down the drive shoulder almost to the drive opening itself. Works great on the outside plugs of my 550, it's still a little snug on the inside plugs, but it works.
Logged
Nick

'76 Honda CB550k
'73 Honda CB750k

Offline TwoTired

  • Really Old Timer ...
  • *******
  • Posts: 21,805
Re: Cold start issues
« Reply #43 on: February 28, 2006, 10:29:32 AM »
Have you checked your bike's tool kit for a spark plug tool?  Or, did the PO keep it for himself?  Honda provided one with the bike originally.
Logged
Lloyd... (SOHC4 #11 Original Mail List)
72 500, 74 550, 75 550K, 75 550F, 76 550F, 77 550F X2, 78 550K, 77 750F X2, 78 750F, 79CX500, 85 700SC, GL1100

Those that learn from history are doomed to repeat it by those that don't learn from history.

Offline n9viw

  • Enthusiast
  • **
  • Posts: 160
  • Floyd, '76 CB550k
Re: Cold start issues
« Reply #44 on: February 28, 2006, 11:40:13 AM »
Yeah, and those buggers are as rare as hens' teeth. My local shop has one, they welded a 3/8" drive socket into the round end so you could use it with a socket wrench. It's a wonderful thing, but those stamped socket drivers are, as I said, incredibly hard to find.
I picked one up at a garage sale, but it was for lawn mowers. Turns out both sides (it was double-ended) were the wrong size- too big, or too small. Oh well, only 0.25 wasted.
Logged
Nick

'76 Honda CB550k
'73 Honda CB750k

Vatch

  • Guest
Re: Cold start issues
« Reply #45 on: February 28, 2006, 12:38:35 PM »
Quote from: lassenc on February 24, 2006, 09:51:20 AM

And a 40 dollar plugtool-thing, cause I didn't have one in 18mm


Seeing as you've already dropped the cash on the tool the best thing I could advise is give the tool a name.  Only expensive tools get names.   :P
Logged

Offline lassenc

  • Hot Shot
  • ***
  • Posts: 266
Re: Cold start issues
« Reply #46 on: February 28, 2006, 01:58:23 PM »
Hehe :) "Useless" come in mind...

Drove 300km on it today, in 5 celcius, my hands and feet were blue when I came home :(
Logged
How exactly do you teach abstinence though?
It's like beating a dead cow, it's fun, but it doens't really get you anywhere.
Pages: 1 [2]   Go Up
« previous next »