Author Topic: Race and Performance parts for sale and wanted.  (Read 270498 times)

0 Members and 1 Guest are viewing this topic.

Offline peter400four

  • Full Member
  • *
  • Posts: 79
Re: Race and Performance parts for sale and wanted.
« Reply #1375 on: May 28, 2018, 12:14:18 am »
Hi Mr Jaguar,
Does your box of HiPo parts by any chance include a road racing camshaft for a '70s CB500/4? Yoshimura or similar.
I'm trying to get a bit more power for my John Blanchard Flying Dragon homage ("replica" would be stretching the truth a bit) so I can be competitive against those pesky 350cc two strokes.
I now have the carbs the original bike ran (26mm, MkII Concentrics), bigger valves, better Springs, the head is being welded up to boost compression so now all I need is the camshaft to make this magic stuff work. (All right, I'll be honest, a Yoshi crank and con rods wouldn't hurt either, but finances dictate that will not happen).
Regards,
Peter.

Offline rudi

  • Full Member
  • *
  • Posts: 49
Re: Race and Performance parts for sale and wanted.
« Reply #1376 on: May 28, 2018, 01:28:19 am »
Hello jaguar,
I am from Germany and I would ask you if the Offered Mikini Carbs are suitabel for Honda cb 400 four?
I could not look at your Pictures......
Genrally Request : I am looking for CB 400 Four Performance Parts, like Keihin , Mikuni Carbs, Yoshimura Camshaft ans so on.....
If somebody had somthing to sell please let me know....

Offline jaguar

  • Old Timer
  • ******
  • Posts: 2,763
Re: Race and Performance parts for sale and wanted.
« Reply #1377 on: May 28, 2018, 05:02:19 am »
Basically everything is long gone.

Offline NalleyRacing

  • Hot Shot
  • ***
  • Posts: 497
  • 1972 Cb750K dragbike Instagram: Drag_racer736
Re: Race and Performance parts for sale and wanted.
« Reply #1378 on: June 09, 2018, 08:27:21 am »
RC ENG angle drive distributor for the CB750. Compleatly rebuilt with new parts as well as a Mallory unilite electronic pickup and MSD blaster II coil. Original RC coil included too
 $1525 shipped to your door Lower 48 only.
« Last Edit: June 14, 2018, 08:51:55 am by NalleyRacing »

Offline Cb750 Racer

  • Enthusiast
  • **
  • Posts: 127
Re: Race and Performance parts for sale and wanted.
« Reply #1379 on: June 22, 2018, 12:18:51 pm »
Parts lot for sale:
Just trying to sell all the extra parts that won't make it into my engine. Best offer takes em! Feel free to pm if you want more pictures or have any questions
PRICES REDUCED
ATP/Rajay 377 B25 - 550$ OBO shipped to your door for the lower 48. Spins freely was pulled off a running bike would recommend rebuilding just to be safe. Also comes with the wastegate and dump free of charge.








Also have a brand new Cycle X optical ignition i'd like to sell comes with coils, rectifier regulator, and a set of taylor plug wires. Asking 300$ shipped for the lot.None of the parts were ever used.






Delrin cush drive bushings along with an NOS Honda slider 100$ shipped also were never used. SOLD


Also have a set of engine tensioners which were never used as well. The cam tensioner used an NOS core.Both were never used. 100$ for both. SOLD



« Last Edit: July 15, 2018, 09:20:53 pm by Cb750 Racer »
Turbo Billet Block cb750
1975 Honda CB400f
1972 Suzuki GT750J
1984 Kawasaki GPZ900 Mr.Turbo Top Gun build
2002 Suzuki Bandit 1200 Turbo
1979 Honda CBX
1990 Mr.Turbo Kawasaki ZX11
And Dozens More...

Offline jaguar

  • Old Timer
  • ******
  • Posts: 2,763
Re: Race and Performance parts for sale and wanted.
« Reply #1380 on: July 19, 2018, 03:48:36 am »
I have some Honda branded NGK D-12H and D14H plugs.
Unsure what they go to, or what they are worth.

Thought some of you racers might be interested

Offline jonnycakes

  • Enthusiast
  • **
  • Posts: 206
Re: Race and Performance parts for sale and wanted.
« Reply #1381 on: July 27, 2018, 10:37:35 am »
Got a line on a complete RC right angle drive with out distibuter or magneto.  Looked to be the wide version made for a magneto.  Its sitting on a shelf safe for now.
'Matic-Fanatic

Offline 754

  • Really Old Timer ...
  • *******
  • Posts: 29,058
Re: Race and Performance parts for sale and wanted.
« Reply #1382 on: August 01, 2018, 03:33:34 pm »
Can you get a pic of it, and  the mounting part ..I  bought a new Kawi unit, but it's way different (mount wise), I would trade it.
 PM sent.
« Last Edit: August 01, 2018, 05:39:07 pm by 754 »
Maker of the WELDLESS 750 Frame Kit
dodogas99@gmail.com
Kelowna B.C.       Canada

My next bike will be a ..ANFOB.....

It's All part of the ADVENTURE...

73 836cc.. Green, had it for 3 decades!!
Lost quite a few CB 750's along the way

Offline jonnycakes

  • Enthusiast
  • **
  • Posts: 206
Re: Race and Performance parts for sale and wanted.
« Reply #1383 on: August 29, 2018, 07:41:40 pm »
Up for sale, a rare wide body RC Enginering right angle drive with a Joe Hunt Magneto complete.  Gears look great.  Throws a spark, but is alittle weak. $1750 OBO

Your chance to own a hen tooth!!!!
'Matic-Fanatic

Offline jaguar

  • Old Timer
  • ******
  • Posts: 2,763
Re: Race and Performance parts for sale and wanted.
« Reply #1384 on: October 03, 2018, 03:44:04 am »
Anyone need service parts for their RC or ARD set ups?

Have caps, rotors, condensers, covers, bearings, oil seals, etc.

If you need something, reach out.

Offline RAZZ

  • Enthusiast
  • **
  • Posts: 127
Re: Race and Performance parts for sale and wanted.
« Reply #1385 on: October 03, 2018, 03:49:38 am »
Hi jag

I have your old ARD from Bill - do you have a belt cover with no holes in ? Pls pm me thx Razz


Sent from my iPhone using Tapatalk

Offline jaguar

  • Old Timer
  • ******
  • Posts: 2,763
Re: Race and Performance parts for sale and wanted.
« Reply #1386 on: October 03, 2018, 12:13:38 pm »
No ARD covers to sell right now.

Do have some drive posts

Offline gschuld

  • Master
  • *****
  • Posts: 2,346
Re: Race and Performance parts for sale and wanted.
« Reply #1387 on: October 11, 2018, 11:16:06 am »
I’m looking for a high compression 410 77/78 f model piston/piston set.

New, used, destroyed.  I’m only interested in a physical representation of the 410 head piston valve angles, position, etc to copy onto another non Honda piston.

Thx

George

Offline bear

  • Vale Bill McIntosh ......"illegitimi non carborundum"
  • Old Timer
  • ******
  • Posts: 2,570
  • Leeton in Australia
Re: Race and Performance parts for sale and wanted.
« Reply #1388 on: October 11, 2018, 07:58:50 pm »
I’m looking for a high compression 410 77/78 f model piston/piston set.

New, used, destroyed.  I’m only interested in a physical representation of the 410 head piston valve angles, position, etc to copy onto another non Honda piston.

Thx

George

There's another way George, pm me.

Cheers,
Brian
The older I get the faster I was.

Offline physician

  • Enthusiast
  • **
  • Posts: 132
  • old school...
    • photo galerie
Re: Race and Performance parts for sale and wanted.
« Reply #1389 on: December 03, 2018, 05:51:03 pm »
Is the ignition /coil/rectifier still available?
Parts lot for sale:
Just trying to sell all the extra parts that won't make it into my engine. Best offer takes em! Feel free to pm if you want more pictures or have any questions
PRICES REDUCED
ATP/Rajay 377 B25 - 550$ OBO shipped to your door for the lower 48. Spins freely was pulled off a running bike would recommend rebuilding just to be safe. Also comes with the wastegate and dump free of charge.








Also have a brand new Cycle X optical ignition i'd like to sell comes with coils, rectifier regulator, and a set of taylor plug wires. Asking 300$ shipped for the lot.None of the parts were ever used.






Delrin cush drive bushings along with an NOS Honda slider 100$ shipped also were never used. SOLD


Also have a set of engine tensioners which were never used as well. The cam tensioner used an NOS core.Both were never used. 100$ for both. SOLD

k2 chassis k7 engine resto mod
k7 cafe/fighter/brat

Offline Don R

  • My Sandcast is a
  • Really Old Timer ...
  • *******
  • Posts: 19,079
  • Saver of unloved motorcycles.
Re: Race and Performance parts for sale and wanted.
« Reply #1390 on: December 09, 2018, 11:33:16 am »
https://www.facebook.com/marketplace/item/160554198218291

 cut cases, heads, injector, no price but someone should check it out, in Indy.

 Edit, apparently he's not answering inquiries.

« Last Edit: December 17, 2018, 09:11:04 pm by Don R »
No matter how many times you paint over a shadow, it's still there.
If you love it, set it free, if it stays it's probably one of my 750's.
 CEO at the no kill motorcycle shop.

Offline CR750

  • Enthusiast
  • **
  • Posts: 161
« Last Edit: January 07, 2019, 05:18:32 am by cr750 »
W r e n c h  ·  R i d e  ·  R e p e a t

Offline Don R

  • My Sandcast is a
  • Really Old Timer ...
  • *******
  • Posts: 19,079
  • Saver of unloved motorcycles.
Re: Race and Performance parts for sale and wanted.
« Reply #1392 on: January 15, 2019, 12:02:01 pm »
 Those might be new and old but far from stock. I have wondered about them also, they look pretty chunky.
No matter how many times you paint over a shadow, it's still there.
If you love it, set it free, if it stays it's probably one of my 750's.
 CEO at the no kill motorcycle shop.

Offline gschuld

  • Master
  • *****
  • Posts: 2,346
Re: Race and Performance parts for sale and wanted.
« Reply #1393 on: January 15, 2019, 05:03:21 pm »
Those might be new and old but far from stock. I have wondered about them also, they look pretty chunky.

Common understanding is they are LOW quality and to be avoided.  No personal experience with them
myself.

George

Offline Tintop

  • Old Timer
  • ******
  • Posts: 3,959
Re: Race and Performance parts for sale and wanted.
« Reply #1394 on: January 15, 2019, 07:22:01 pm »
In the description it says you have the clearance the cases, so any savings on rod cost (of debatable quality) is gone to machining. ::)
1977 CB550/4 Cafe - Speed Warrior / BOTM 03/11
1980 CB750F (project)
Whittaker GBF Vintage Racing Sidecar (XS750 power) - ITG / 151's / CMR Racing Products (SOLD)
1976 CB400 SS - stock / BOTM 04/11 (SOLD)
1973 CB750 K - basket case (SOLD)
77 CB550 Cafe build
550/750 Filter Thread
Sidecar Rebuild Thread

Offline POPS 911

  • Expert
  • ****
  • Posts: 926
29's smooth bores
« Reply #1395 on: February 13, 2019, 08:39:24 am »
Used them for years, great shape w/chrome stacks ............ stored in a controlled room in my home.

POPS BK911

Offline Don R

  • My Sandcast is a
  • Really Old Timer ...
  • *******
  • Posts: 19,079
  • Saver of unloved motorcycles.
Re: Race and Performance parts for sale and wanted.
« Reply #1396 on: February 14, 2019, 08:18:47 pm »
Asking price Pops?
No matter how many times you paint over a shadow, it's still there.
If you love it, set it free, if it stays it's probably one of my 750's.
 CEO at the no kill motorcycle shop.

Offline macvit7906

  • Enthusiast
  • **
  • Posts: 221
Re: Race and Performance parts for sale and wanted.
« Reply #1397 on: February 23, 2019, 11:21:34 am »
****SOLD****


Hi All,

I recently acquired a barn find CB750f as a parts bike for a couple of cb750s I'm working on.
Right off the bat, I could tell the engine had been raced. No kick start or starter motor gears, after market cam and springs, RSC slipper pistons, lightened rotor.
The engine serial number placed the engine as an early k5, with earlier K3 or K2 head and cyls. 
Upon cracking the case I found a different looking aftermarket transmission.

An experienced forum member contacted me and helped me determine what it was. We confirmed it is an RSC close ratio racing transmission!
ratios:
24/41
27/38
30/36
30/32
34/31

Final drive 48/56

Now, I'm not a racer, and I know this would be of value to some of you. I'd rather see it go to a good home, as my wife wont let me mount it on a shelf.
I'll clean it up and get some better pictures for you all, but I am going to sell it. I'm not sure what a fair price would be, but if you're interested, PM me and let me know!

Overall, it's in very good shape. I checked every tooth - no chips, no scouring, no unusual wear.


« Last Edit: March 14, 2019, 07:11:56 pm by macvit7906 »

Offline seanbarney41

  • not really that much younger than an
  • Really Old Timer ...
  • *******
  • Posts: 10,539
Re: Race and Performance parts for sale and wanted.
« Reply #1398 on: February 23, 2019, 11:51:03 am »
Macvit, I am interested in those gears.  Need some time to do some research and I will pm you.
If it works good, it looks good...

Offline macvit7906

  • Enthusiast
  • **
  • Posts: 221
Re: Race and Performance parts for sale and wanted.
« Reply #1399 on: February 23, 2019, 06:05:48 pm »
Macvit, I am interested in those gears.  Need some time to do some research and I will pm you.

sounds good