Author Topic: Race and Performance parts for sale and wanted. (Read 294086 times)

bwaller · « **Reply #1400 on:** February 26, 2019, 02:46:41 PM »

That is ultra close ratio, interesting if it is actually Honda. Total reduction of 47% is tight. It is not from Nova. I wonder if George can dig up ratios from the actual CR kit?

To be certain that tall 1st gear would not be fun on the street.

Jerry Rxman Griffin aka MuthaF'er · « **Reply #1401 on:** February 26, 2019, 03:26:42 PM »

Yoshi?

gschuld · « **Reply #1402 on:** February 26, 2019, 08:47:21 PM »

It appears to be a Honda kit trans and has a presumptive new owner.

George

macvit7906 · « **Reply #1403 on:** March 09, 2019, 12:51:16 PM »

Hi All,

From the same engine the RSC trans came out of, also selling the lightened alternator rotor from R.C. Engineering.

Really clean, and in really nice shape. I have no use for it, as it's purely for racing with minimal charge, with the start clutch gone.

I'm assuming it was balanced as well.

Not sure what a far price would be - maybe $100 plus shipping? PM me if interested.

Greggo · « **Reply #1404 on:** March 17, 2019, 11:04:39 AM »

CB750 Weber carburetor setup with RC manifold, K0 carb boots/clamps and extra jets/bits up for sale. These are jetted roughly for a stock 750 motor. They were built up at a cost of about $1,300, run bone dry on a small test tank about three years ago and sat on the unfinished bike since. Need the cash so they must go. Carbs, manifold, boots, clamps, extra jets/parts all included. Carbs and manifold will be separated and packed individually to avoid any damage.

Asking $1,000 shipped.

CBJoe · « **Reply #1405 on:** April 03, 2019, 03:29:44 PM »

SOLD

Keihin CR29 Carbs - lightly used. These carbs were completely rebuilt in the fall with genuine Keihin Kits. They only had a short run and test time on non-ethanol fuel only before being run dry. See video at the end for the last run. Bike they were on is an 836 w/ JMR Stage 3 Head. Asking $900 + Shipping

- Original Box
- Extra 120 and 125 Jets
- Original Stacks/adapters
- Remote Idle kit
- 4 K&N Filters

Current Settings:
Main Jet 115
Slow Jet 60
Air Jet 240
Starter Jet 40
Throttle Valve 2.5
Float Height 14mm
Needle (YY8) 3 notch from Top

"

slikwilli420 · « **Reply #1406 on:** April 25, 2019, 05:04:16 PM »

Want to buy for my CB750 superbike project:

Vintage AP Lockheed calipers. I can get the new ones but they say AP Racing, and the older ones look the same but say AP Lockheed, need 2 of those in same condition.

corky · « **Reply #1407 on:** August 19, 2019, 11:29:38 AM »

Hey guys,

I have some unused MC connecting rods for sale. $50.00 + shipping.

Thanks,
Daniel

macvit7906 · « **Reply #1408 on:** August 22, 2019, 12:44:26 PM »

I've got a Kenny Harmon D Grind Camshaft in great shape.

Asking $200 shipped - open to offers

PM me if interested

Don R · « **Reply #1409 on:** September 27, 2019, 08:26:17 PM »

Someone was on Facebook looking for a D. the sandcast and diecast page maybe.

AdrenalineReaper · « **Reply #1410 on:** September 30, 2019, 06:40:01 PM »

Cb750k MotoGPWerks stainless 4 into 1 like new. Found in garage. Open to offers. Pm me.

Sent from my iPhone using Tapatalk

AdrenalineReaper · « **Reply #1411 on:** September 30, 2019, 06:52:46 PM »

Magnum turbo cracked lug and worn impeller fins still very serviceable. Open to offers, it’s just been a conversation piece on my bench for years...

Sent from my iPhone using Tapatalk

AdrenalineReaper · « **Reply #1412 on:** September 30, 2019, 07:00:03 PM »

Also I have The last one the late Cavebears cb’s. High comp engine, dual chain, runs great!

wheelie bars not in picture, open to offers. Not looking to get rich. Bike is in northern IL. No title never bothered, but as some know, previous owner has passed.

Sent from my iPhone using Tapatalk

zoomzoom · « **Reply #1413 on:** October 19, 2019, 06:29:59 AM »

Looking for CB750 turbo kit, please help

RAZZ · « **Reply #1414 on:** October 19, 2019, 09:54:14 AM »

Quote from: zoomzoom on October 19, 2019, 06:29:59 AM

Looking for CB750 turbo kit, please help

There is This turbo project on the 750 Facebook group:

https://www.facebook.com/groups/359016746441?view=permalink&id=10156139530596442

Sent from my iPhone using Tapatalk

Medyo Bastos · « **Reply #1415 on:** October 19, 2019, 03:33:04 PM »

Quote from: zoomzoom on October 19, 2019, 06:29:59 AM

Looking for CB750 turbo kit, please help

I will let you know what I find under my bed.

Sent from my iPhone using Tapatalk

eli · « **Reply #1416 on:** November 08, 2019, 09:13:43 AM »

Quote from: zoomzoom on October 19, 2019, 06:29:59 AM

Looking for CB750 turbo kit, please help

Hi, I'm considering selling mine. Have a look in the for sale area...

y2kc0wb0y · « **Reply #1417 on:** December 17, 2019, 06:29:42 AM »

WTB: Kenny Harmon D grind for CB750 - offering $200.00 shipped.

RP · « **Reply #1418 on:** January 10, 2020, 02:37:10 PM »

R.C. Engineering Extended Swingarm and Struts $300 Hurst/Airheart rear caliper, Disc, master $200

https://www.ebay.com/itm/333475161224

Swingarm SOLD......Brakes SOLD

relisted with make offer https://www.ebay.com/itm/333487276324

corky · « **Reply #1419 on:** February 10, 2020, 06:22:57 PM »

Hey guys,

I am selling the following Crane camshaft. I attached the cam card. It is way to big for anything I am ever going to build, and figured I would see if anyone on here wanted it.

I am asking $400 for it.

Thanks,
Daniel

scottly · « **Reply #1420 on:** February 10, 2020, 06:44:48 PM »

I don't think I've ever seen a cam card with a spec for valve float RPM before?!

corky · « **Reply #1421 on:** March 06, 2020, 08:43:38 AM »

Quote from: corky on February 10, 2020, 06:22:57 PM

Hey guys,

I am selling the following Crane camshaft. I attached the cam card. It is way to big for anything I am ever going to build, and figured I would see if anyone on here wanted it.

I am asking $400 for it.

Thanks,
Daniel

I am coming down to $275, shipped.

Thanks,
Daniel

Medyo Bastos · « **Reply #1422 on:** March 07, 2020, 05:34:27 PM »

MPD Dual Weber Manifold 300 bones net plus shipping. It’s got a repair that is shown in pics, and shouldn’t affect performance.

Sent from my iPhone using Tapatalk

Medyo Bastos · « **Reply #1423 on:** March 11, 2020, 02:41:06 PM »

FOR SALE - ARD Magneto for cb750; bolt on and go 1000 net bones shipped in the mainland

Sent from my iPhone using Tapatalk

ttr400 · « **Reply #1424 on:** May 08, 2020, 03:56:12 AM »

For sale, CR750 clutch cable.

NOS never fitted.

Part number: 22870-300-970

$100.00 or make an offer. will ship worldwide for $10.00. but can only ship after our lockdown is over.

News:

Author Topic: Race and Performance parts for sale and wanted. (Read 294086 times)