« previous next »
Pages: [1]   Go Down

Author Topic: AN fitting questions  (Read 1269 times)

0 Members and 1 Guest are viewing this topic.

Offline anotherCB

  • Hot Shot
  • ***
  • Posts: 407
AN fitting questions
« on: November 15, 2011, 04:27:12 PM »
I am having a custom oil tank built for my 750. I will be using the attached AN fittings on the lines and AN bungs on the tank. I have read that a sealant (Teflon, thread sealer, etc.) MUST NOT BE USED with AN-fittings, can someone confirm that? 
Thx.


Logged
1978 CB750K, 2016 R1200 GS/LC, 1973 R75/5

Offline TommyT

  • Full Member
  • *
  • Posts: 76
Re: AN fitting questions
« Reply #1 on: November 15, 2011, 04:35:07 PM »
YOu don't need anything like that since it's a tapered seat.  It would be like using teflon tape on brake fittings.
Logged

Offline Leanier

  • Enthusiast
  • **
  • Posts: 147
Re: AN fitting questions
« Reply #2 on: November 15, 2011, 04:36:32 PM »
Yea, the seal is not actually made by the threads, thus no use of teflon tape.  the seal is made by the cup and cone of the tapered fitting contacting each other.
Logged
My motorcycle collection thus far:
'74 CB360
'73 CB750
'72 CB125s
'68 CA160

Offline City Boy

  • Hot Shot
  • ***
  • Posts: 689
Re: AN fitting questions
« Reply #3 on: November 15, 2011, 04:36:46 PM »
Hi.The fittings you describe do not seal by the threads but rather by a tapered seat on the male and female.    Rock On
Logged
'52 Kiekhaefer Mercury Rocket Hurricane KG4H
'70 750/RC 1000 Original Owner
'83 1100F

Offline anotherCB

  • Hot Shot
  • ***
  • Posts: 407
Re: AN fitting questions
« Reply #4 on: November 15, 2011, 04:53:55 PM »
Ok, thanks!
Logged
1978 CB750K, 2016 R1200 GS/LC, 1973 R75/5

72500john

  • Guest
Re: AN fitting questions
« Reply #5 on: November 16, 2011, 04:20:27 PM »
just remeber to convert everything over to an fittings. sae flares are 45 degress and an are 37.5. most modern aircraft flex hoses are teflon since it will work with just about any fluid.. as far as part numbers for fittings/unions and the such a d suffux will designate aluminium, a j will be stainless and no suuufex will be plated steel. ei an924-4d= 1/4 dia aluminum. teflon tape is usally not needed on flared fittings but i use it on pipe thread. also you can use a thread sealing grade of loctite. sorry dont know the number of it off the top of my head. have fun and good luck!!
Logged

Offline anotherCB

  • Hot Shot
  • ***
  • Posts: 407
Re: AN fitting questions
« Reply #6 on: November 16, 2011, 04:48:11 PM »
Thanks. I am using all (unfortunately expensive...) -10 AN fittings, -10AN ss hose and AN bungs in the tank, so hopefully I Am ok....we shall see :-)
Logged
1978 CB750K, 2016 R1200 GS/LC, 1973 R75/5

Offline 23tbucket

  • Enthusiast
  • **
  • Posts: 135
Re: AN fitting questions
« Reply #7 on: November 16, 2011, 05:03:03 PM »
JIC and AN fittings are identical and interchangeable however JIC are mallable metal whereas AN (Army/Navy) are all aluminum.
As was mentioned SAE fittings have different angles and should never be used together with either JIC or AN fittings.
The sizes are in 1/16" increments...#10 would be 10 times 1/16 = 10/16" or 5/8" . This is the OD of the tubing.
Logged

Offline anotherCB

  • Hot Shot
  • ***
  • Posts: 407
Re: AN fitting questions
« Reply #8 on: November 16, 2011, 06:13:52 PM »
Yes, that's how I came to decide I needed AN-10. In the meantime I have learned that there are much cheaper options (e.g NPT with Teflon), however I like the looks of the AN.
Logged
1978 CB750K, 2016 R1200 GS/LC, 1973 R75/5
Pages: [1]   Go Up
« previous next »