Author Topic: Bill's Stroker Build VII (Read 26232 times)

BPellerine · « **Reply #25 on:** January 30, 2014, 10:04:01 AM »

yeah where does he get this stuff,does he have an rc sniffing dog?haha bill

dragracer · « **Reply #26 on:** January 30, 2014, 10:17:44 AM »

Quote from: BPellerine on January 30, 2014, 10:04:01 AM

yeah where does he get this stuff,does he have an rc sniffing dog?haha bill

Hahahaha, I think you might be on to something. His dog is always taking parts out of the garage and playing with it.

dragracer · « **Reply #27 on:** January 30, 2014, 10:21:14 AM »

Quote from: joe p on January 30, 2014, 09:34:22 AM

I ran a Cobra motor on my dragbike with a 18 X 5.5 G/Y years ago. What times are you looking for with this setup? Wish I had the money to do this, I'm still trying to get my street 750 going .
I hope you posted picture of this build. I enjoy this stuff.

I'm thinking a 18x5.5 would be best myself on a 4.5" rim. He could save that wide PM wheel for the chromemoly Pena chassis.

PeWe · « **Reply #28 on:** January 30, 2014, 10:25:43 AM »

WOW!
More photos please! It's like striptease,

mechanical version

joe p · « **Reply #29 on:** January 30, 2014, 10:59:19 AM »

I ran a Cobra motor on my dragbike with a 18 X 5.5 G/Y years ago. What times are you looking for with this setup? Wish I had the money to do this, I'm still trying to get my street 750 going .
I hope you posted picture of this build. I enjoy this stuff.

joe p · « **Reply #30 on:** January 30, 2014, 11:28:58 AM »

That was not what I wanted to do.

Bill/BentON Racing · « **Reply #31 on:** January 30, 2014, 02:01:18 PM »

Time to dig out the other raked frame with the chrome Clubfoot. Pics to follow. There was a set of Webers on Denver Craig's list. Made an offer, got no reply.RC manifold.
Joe P what times did you run, any pics? Alfred went to play bingo!

Bill
You do need to come to Atlanta. Wait til snows gone!! Haha.

joe p · « **Reply #32 on:** January 30, 2014, 03:12:45 PM »

I ran 10.50 but at the time I was 230lbs, I know a guy that ran S/G (9.90) with the same setup I had but he was a little guy about 120 lbs.

Bill/BentON Racing · « **Reply #33 on:** January 30, 2014, 03:22:13 PM »

Think I was told this ran consistently in low 10's. Hope they were right. Took some pics of raked frame and clubfoot swingarm. Looks promising. Pics in a few, Bill

BPellerine · « **Reply #34 on:** January 30, 2014, 04:01:25 PM »

gotta teach the dog to find carbs.haha bill

Sam Green Racing · « **Reply #35 on:** January 30, 2014, 04:27:39 PM »

That dog is called Baby Face and it can find anything, usually all the things you don't want it to find.

but then YOU can't find them.

ask me how I know.

Sam.

Bill/BentON Racing · « **Reply #36 on:** January 30, 2014, 04:31:07 PM »

Here we go! We on a mission Frank!

Yep,been raked the old fashioned way!

Additional bracing/clubfoot

more brackets

I like it!

I really like!

Its a cute rt side STAND! Sam!lol!

dragracer · « **Reply #37 on:** January 30, 2014, 06:51:30 PM »

Good start. Do we have axle adjusters for the back?. Other than the PM wheel, what other choices do we have?? And what about a front wheel?? Front end??

I know we got electronics via the MSD box. Carbs?? Well, might have to see what you can come up with there. Jon Weeks is a firm believer in re-racking carbs where the spacing is close- we may need to investigate that option. One of which is carbs from an FJ1100 or 1200, or carbs from a 900 Ninja, 84 or 85- all of which could be readily available on Ebay. The 36mm Mikuni flat slides on my F model are actually fitted for either of the bikes i mentioned above. The carbs boots were offset ground so i didn't have to re-space the carbs.

Bill/BentON Racing · « **Reply #38 on:** January 30, 2014, 08:15:38 PM »

POPS has some 34's FS.

He sold the 36's.

bear · « **Reply #39 on:** January 31, 2014, 05:14:21 PM »

Quote from: Bill/BentON Racing on January 29, 2014, 07:13:54 AM

Medyo, will call later today, Bill
Jerry, big auto stuck waiting on finding some CB1100F rods.
So going to build/ run RC Cobra engine or what looks like one!

As mentiond in an earlier post on another thread, I have a good set of MA3 rods.
I'm happy to send them over.
You can replace them later when you find a set.

Cheers,
Brian

Bill/BentON Racing · « **Reply #40 on:** February 01, 2014, 04:57:34 AM »

Bear, I remember!

just was hoping to not have to go there. But I was getting ready to PM you about them! Just last night a forum member asked for my shipping addy!!

Lets make sure, if so will let you and forum know who! I will say he's a bunch of fun to be around! And I think he's got the fever to build a Dragbike now..............and he CAN do it!

Bill

Bill/BentON Racing · « **Reply #41 on:** February 01, 2014, 11:21:57 AM »

Rods on the way! Thank you KMB69! You da man!

Look what I found,this might help top end! Bill

Bought a 18x5.5 inch Kosman/Denco rear wheel on ebay.came off a old Denco H2 racer.

Bill/BentON Racing · « **Reply #42 on:** February 01, 2014, 04:48:27 PM »

This jumped off the bench,said use me!!!

Another of engine,also came with Cobra motor!

Looks like copper headgasket.

Tracy Turnpike Terror!!!!!!

Don't worry it'll sit lower!

What y'all think?

BPellerine · « **Reply #43 on:** February 01, 2014, 04:58:30 PM »

looks like a 70s dragbike to me!gonna be a mean one eh!bill

Bill/BentON Racing · « **Reply #44 on:** February 01, 2014, 05:04:06 PM »

Bill, that's what I want a cool retro old school looking dragbike! Oh yeh that runs in the 10's!

High 9's when Frank's nitrous setup kicks in! Wake up Bill! Oh!

BPellerine · « **Reply #45 on:** February 01, 2014, 05:44:47 PM »

gonna have to strap yourself on!bill

dragracer · « **Reply #46 on:** February 01, 2014, 11:37:36 PM »

Quote from: Bill/BentON Racing on February 01, 2014, 05:04:06 PM

Bill, that's what I want a cool retro old school looking dragbike! Oh yeh that runs in the 10's! High 9's when Frank's nitrous setup kicks in! Wake up Bill! Oh!

Oh boy, we're making progress now. Looking good man.

Ironically Bill, i'm in the process of setting up a nitrous system on a fellow CSRA Dragbike Association member's bike right now. So..... we now have another waiting in the wings it seems- SOHC did you say??

Bill/BentON Racing · « **Reply #47 on:** February 02, 2014, 04:11:51 AM »

Nitrous.... The first time.....kinda like the first time on boost! What a rush! Frank, the sky's the limit on this one! We can do what WE want!

pulling out wheelie bars and rear wheels today. Bike has Dyna S, I have new green Dyna coils,the MSD box.Ignition covered. Got to buy a V&H Sidewinder! Got a tapered bearing set for front.Can run F front forks, can modify if ness. Got a GSXR rear wheel with 5.5 Goodyear still mounted,3 spoke. Also PM, and the Kosman/Denco one coming. So I say get running N/A first,then hit it with a shot!

Bill more pics later today.

dragracer · « **Reply #48 on:** February 02, 2014, 11:19:58 PM »

This will be you Bill!!!!

Sam Green Racing · « **Reply #49 on:** February 03, 2014, 12:35:03 AM »

News:

Author Topic: Bill's Stroker Build VII (Read 26232 times)