Author Topic: What did you do to your bike today ? (Read 3234832 times)

bigreno · « **Reply #9500 on:** March 10, 2012, 12:32:30 AM »

Today I put on a17 inch spoke wheel rear .and adjusted the cam chain .another week and it will be ready for a long ride

mick7504 · « **Reply #9501 on:** March 10, 2012, 02:17:33 AM »

It's 7kph (4mph) leeway here in the NT.
After that, it's bend over boy and scratch out a Gregory Peck. (cheque)

Not worth fighting it in court as some have already tried.
The cameras are tested for accuracy and certified regularly so there's no arguments about it.

Dimitri13 · « **Reply #9502 on:** March 10, 2012, 09:42:06 AM »

Wow, that's pretty crazy. On a good day (no rain, dry raods, little traffic) I'll do 10-15 over, just so I'm "moving" to other motorists. I don't slow down when I see radar cops, unless there's a wall of cars in front of me that did.

Hablo · « **Reply #9503 on:** March 10, 2012, 10:00:14 AM »

Last night...went to a friends and welded up a hole in the bottom of one muffler, and ground it smooth.
Doesn't look so pretty but it's hardly visible.

Randy · « **Reply #9504 on:** March 10, 2012, 10:06:47 AM »

Taking her out for a ride today.. real nice weather in Los Angeles

70CB750 · « **Reply #9505 on:** March 10, 2012, 02:05:31 PM »

Took off the rear wheel to fix a flat.

dave500 · « **Reply #9506 on:** March 10, 2012, 09:13:03 PM »

recieved some new valve guide seals the other day so after a ride down to brunswick heads and back i reasembled a head for the spares shelf.

grcamna2 · « **Reply #9507 on:** March 10, 2012, 09:33:13 PM »

Quote from: Hablo on March 10, 2012, 10:00:14 AM

Last night...went to a friends and welded up a hole in the bottom of one muffler, and ground it smooth.
Doesn't look so pretty but it's hardly visible.

It's nice to be able to keep the Stockers on the bike as long as you can..I like fixing my O.E. mufflers,they don't make 'em anymore.

70CB750 · « **Reply #9508 on:** March 11, 2012, 12:18:30 PM »

Fixed the flat and poked two more holes in the tube when mounting - can you say moron?

ekpent · « **Reply #9509 on:** March 11, 2012, 12:32:30 PM »

Moron

Think we have all done that at least once

wardenerd · « **Reply #9510 on:** March 11, 2012, 02:38:14 PM »

sanding the 550 for return to factory colors

Stev-o · « **Reply #9511 on:** March 11, 2012, 03:02:16 PM »

Cleaned up the 550 and went for a ride in the Hill Country...

Shane72 · « **Reply #9512 on:** March 11, 2012, 03:19:37 PM »

Put on the new Hagons, then promptly went on a ride with a friend and ran out of gas.

A minor inconvenience, and great to be out in good weather again!

Shane

CycleRanger · « **Reply #9513 on:** March 11, 2012, 05:03:35 PM »

Changed the oil on XL250s. Rode it around a bit more to break in the new piston.
Decided it needs a new clutch. Oh well.

Since it was such damn fine day I fired up the K5 and went for a ride to celebrate DST.
Stopped for Thai food on the way home.

Didn't see Steve-o!

Stev-o · « **Reply #9514 on:** March 11, 2012, 05:08:36 PM »

Quote from: CycleRanger on March 11, 2012, 05:03:35 PM

Stopped for Thai food on the way home.

Didn't see Steve-o!

Thai food again? [love it]. Italian for me.

You are on the other side of the world! [actually Lake Travis]

hoodellyhoo · « **Reply #9515 on:** March 11, 2012, 06:08:28 PM »

Yesterday I helped my dad install a new exhaust on the K2. It's a nos mc enterprises brand 4-2. It took a long time to figure out what went where since there were no directions.

CycleRanger · « **Reply #9516 on:** March 11, 2012, 06:16:44 PM »

Quote from: Stev-o on March 11, 2012, 05:08:36 PM

Quote from: CycleRanger on March 11, 2012, 05:03:35 PM

Stopped for Thai food on the way home.

Didn't see Steve-o!

Thai food again? [love it]. Italian for me.

You are on the other side of the world! [actually Lake Travis]

Yeah, we gotta meet up in the middle some time! (Well, not in the middle of the lake!)

Quote from: hoodellyhoo on March 11, 2012, 06:08:28 PM

Yesterday I helped my dad install a new exhaust on the K2. It's a nos mc enterprises brand 4-2. It took a long time to figure out what went where since there were no directions.

Wow, those pipes look great!

bayerja · « **Reply #9517 on:** March 11, 2012, 06:28:04 PM »

I pulled the head cover off my cb500 to tighten the head bolts. I just rebuilt the entire bike and placed a new head gasket in since it was leaking oil out of it. Took it out yesterday for a ride and it leaked oil again. Even worse this time. When I checked the head bolts though with a torque wrench they were already tighter than the specified value in the manual. So I loosened the bolts up and retorqued then to spec.

Dont want to thread jack, but could too tight wad bolts cause the oil leak around the gasket?

Dimitri13 · « **Reply #9518 on:** March 11, 2012, 11:13:52 PM »

Installed clip-ons. You can read about it in my build thread:

http://forums.sohc4.net/index.php?topic=101783.msg1158363#msg1158363

tweakin · « **Reply #9519 on:** March 12, 2012, 05:59:40 AM »

Started to clean and polish my old 836 for its new home. It is going in a 1978 cb750f which is going to remain mostly stock with some minor twists, such as polished covers on the all black engine.

heffay · « **Reply #9520 on:** March 12, 2012, 09:42:02 AM »

shiny

Tews19 · « **Reply #9521 on:** March 12, 2012, 10:19:29 AM »

I got my temps renewed to enable me to drive my bikes legally until my road test in May.

strynboen · « **Reply #9522 on:** March 12, 2012, 01:05:30 PM »

have polished the instrument panel on my cbx
have polished all black alu parts..like front forks ,brake calibers ,engine parts..instrument faces..and put a crome front fender instead that plastic type..

first idea vas a classic cb 1100..but that have not kaburetores,,and looks to new...så bayed a old cbx..and vill build a cb 750 seat and rear krome fender light..and all that old stuff on..to make a real klassic super bike..with orginal honda parts only...
but have dropped that idea..like the cbx as it are..just.. fantastic a mix of old cb and the 4 valve head engine...simpel and advansed at same time

1978 Castrol Six Hour Production Bike Race - Amaroo Park - Pt2
part 2.....cbx can be raced..

maduncle · « **Reply #9523 on:** March 12, 2012, 07:20:40 PM »

Quote from: strynboen on March 12, 2012, 01:05:30 PM

have polished the instrument panel on my cbx

Sweet!

I didn't know that CBX instrument panels look that good.

Hmmm - might work on a VFR streetfighter...

ThomasD883 · « **Reply #9524 on:** March 12, 2012, 08:40:06 PM »

I absolutely without a doubt think the cbx is the bee's knee's. It's got to be the most striking motorcycle, road bike, I've ever seen. All that motor up front has a very big presence. You lucky sob

any pics of the whole bike?

News:

Author Topic: What did you do to your bike today ? (Read 3234832 times)

maduncle