« previous next »
Pages: [1]   Go Down

Author Topic: How many ball bearings in the neck?  (Read 3338 times)

0 Members and 1 Guest are viewing this topic.

Offline Kustomizer

  • Full Member
  • *
  • Posts: 89
How many ball bearings in the neck?
« on: January 02, 2015, 05:48:38 PM »
Ok, I didn't realize that the ball bearing in the neck were free and not enclosed, so I dropped a couple and now I'm not sure I found them all.  Can  someone tell me how many ball bearings are in the top and bottom of the steering neck?
Logged

Offline goldarrow

  • one day, i'll be an
  • Old Timer
  • ******
  • Posts: 3,360
Re: How many ball bearings in the neck?
« Reply #1 on: January 02, 2015, 05:50:29 PM »
Somewhere around 19 and 18
Logged
Life Is Full Of Challenges - And My Backyard Is Full Of SOHC4's

CB550 K0
CB750 K0, K2, K23 JDM, K45, K5
And the little ones z50r, xr50r, st90


750k5 http://forums.sohc4.net/index.php?topic=114817.0

Offline bjbuchanan

  • Master
  • *****
  • Posts: 2,274
Re: How many ball bearings in the neck?
« Reply #2 on: January 02, 2015, 05:58:31 PM »
Quote from: goldarrow on January 02, 2015, 05:50:29 PM
Somewhere around 19 and 18

I remember 19.

A good time for allballz tapered set to replace your old set of bearings? It's only like 30$
Logged
The dirty girl-1976 cb750k, Ebay 836, Tracy bodykit
Round top carbs w/ 38 pilots, middle needle position, airscrew 7/8ths out, 122 main jet
Stock airbox w/ drop in K&N, Hooker 4-1

Don't trust me alone with a claw hammer and some pliers

Offline Prospect

  • Expert
  • ****
  • Posts: 1,174
Re: How many ball bearings in the neck?
« Reply #3 on: January 02, 2015, 05:59:54 PM »
I remember 19 on top and 18 on the bottom. 
Logged
Current Bikes

1969 CB750  Sandcast #256
1971 CB750K1
1972 CB750K1
1975 CB400F
1975 GL1000 Goldwing
1954 Harley Davidson Panhead
1957 Harley Davidson Panhead

Toronto Canada

Offline oldhatt45

  • The person called in at the last minute to share the blame is the...
  • Expert
  • ****
  • Posts: 900
  • Just an Old Guy that's gone to the Dogs
Re: How many ball bearings in the neck?
« Reply #4 on: January 02, 2015, 06:06:48 PM »
According to the Shop Manual (page 118) there are 18 on the upper and 19 on the lower.
Except the ones that are rolling around on the floor.  LOL

Like bjbuchanan said, go get the All Balls Tapered bearings.  Then you can just put your balls where they belong.  ROFL :0 :)

Charlie
Logged

Offline Stev-o

  • Ain't no
  • Really Old Timer ...
  • *******
  • Posts: 34,962
  • Central Texas
Re: How many ball bearings in the neck?
« Reply #5 on: January 02, 2015, 06:12:55 PM »
It's best to have 0 - time to upgrade.
Logged
'74 "Big Bang" Honda 750K [836].....'76 Honda 550F.....K3 Park Racer!......and a Bomber!............plus plus plus.........

Offline Kustomizer

  • Full Member
  • *
  • Posts: 89
Re: How many ball bearings in the neck?
« Reply #6 on: January 04, 2015, 07:35:17 PM »
LOL!  Ok, thanks for the info!
Logged

Offline DWS

  • Enthusiast
  • **
  • Posts: 204
  • Treat others as you would like to be treated .
Re: How many ball bearings in the neck?
« Reply #7 on: January 04, 2015, 07:44:59 PM »
Keep them greased up, what ever you do.  :-[
« Last Edit: January 04, 2015, 07:47:43 PM by DWS »
Logged
Always looking for friends.

78CB750F3
PD 42A with original breadbox
4 into 1
valves adjusted to .003 (intake and exhaust) ( as was suggested for cooling )
slow jets#35 Main #110
 turned out to 1.5 some paper work says 1.75
4800 feet altitude

78 Honda CB 750 F3 Restoring now(Almost done)
BSA MX 50 Next
BSA b50T Parts

Offline Bankerdanny

  • Eventually I will be old enough in reality to be
  • Really Old Timer ...
  • *******
  • Posts: 7,623
  • Endeavor to persevere
Re: How many ball bearings in the neck?
« Reply #8 on: January 05, 2015, 03:16:53 PM »
If your races don't have any grooves in them there is no shame in keeping the ball bearings. The tapered conversion is not expensive, but it's a pain in the ass and a propery adjusted headset works just fine.
Logged
"The problem with quotes on the Internet is that you never know if they're true" - Abraham Lincoln

Current: '76 CB750F. Previous:  '75 CB550F, 2007 Yamaha Vino 125 Scooter, '75 Harley FXE Superglide, '77 GL1000, '77 CB550k, '68 Suzuki K10 80, '68 Yamaha YR2, '69 BMW R69S, '71 Honda SL175, '02 Royal Enfield Bullet 500, '89 Yamaha FJ1200

Offline BobbyR

  • Really Old Timer ...
  • *******
  • Posts: 12,365
  • Proud Owner of the Babe Thread & Dirty Old Man
Re: How many ball bearings in the neck?
« Reply #9 on: January 05, 2015, 06:19:01 PM »
Since you are this far into it, you may as well swap them out. They get a notch in them that craps up the handing. If you do a search you will find threads where they jave the number of the bearing and you get get it from a non bike source which is cheaper.
Logged
Dedicated to Sgt. Howard Bruckner 1950 - 1969. KIA LONG KHANH.

But we were boys, and boys will be boys, and so they will. To us, everything was dangerous, but what of that? Had we not been made to live forever?

Offline 70CB750

  • Labor omnia vincit improbus.
  • Really Old Timer ...
  • *******
  • Posts: 14,817
  • Northern Virginia
Re: How many ball bearings in the neck?
« Reply #10 on: January 06, 2015, 03:21:51 AM »
« Last Edit: January 06, 2015, 03:24:52 AM by 70CB750 »
Logged
Prokop
_______________
Pure Gas - find ethanol free gas station near you

I love it when parts come together.

Dorothy - my CB750
CB750K3F - The Red
Sidecar


CB900C

2006 KLR650

Offline ekpent

  • Really Old Timer ...
  • *******
  • Posts: 13,508
  • To many bikes-but lookin' for more
Re: How many ball bearings in the neck?
« Reply #11 on: January 06, 2015, 08:02:17 AM »
 I just received two sets I bought on E-bay for $50.52 or $25.26 each + free shipping recently. My everyday rider is very notchy so out with the old since I am going in.
Logged

Offline Kustomizer

  • Full Member
  • *
  • Posts: 89
Re: How many ball bearings in the neck?
« Reply #12 on: January 06, 2015, 08:22:03 PM »
Great info, thanks!
Logged
Pages: [1]   Go Up
« previous next »