« previous next »
Pages: [1]   Go Down

Author Topic: Whats your favorite metal filler (minor pitting)  (Read 527 times)

0 Members and 1 Guest are viewing this topic.

Offline CBJoe

  • Master
  • *****
  • Posts: 1,976
Whats your favorite metal filler (minor pitting)
« on: March 31, 2021, 06:52:02 PM »
As opposed to bondo or JB weld....what is your favorite filler for non structural rust pitting in frame?   Especially in high use areas such as the center stand?  Not powder coating....just enamel or epoxy painting.

« Last Edit: March 31, 2021, 06:53:47 PM by CBJoe »
Logged
'07 Bonneville Black
'15 Moto Guzzi California 1400
CB750K2 Hot Rod Revival http://forums.sohc4.net/index.php/topic,171693.0.html
'65 CB77
'66 CM91 (C90'ish)

Online jgger

  • Master
  • *****
  • Posts: 2,384
Re: Whats your favorite metal filler (minor pitting)
« Reply #1 on: March 31, 2021, 07:42:26 PM »
Brazing rod works pretty good. Thats if you have the torch for it.
Logged
"The SOHC4 uses a computer located about 2-3 ft above the seat.  Those sometimes need additional programming." -stolen from  Two Tired

The difference between an ass kisser and brown noser is merely depth perception.  Stolen from RAFster122s

Offline Don R

  • My Sandcast is a
  • Really Old Timer ...
  • *******
  • Posts: 20,418
  • Saver of unloved motorcycles.
Re: Whats your favorite metal filler (minor pitting)
« Reply #2 on: March 31, 2021, 09:02:35 PM »
Logged
No matter how many times you paint over a shadow, it's still there.
 CEO at the no kill motorcycle shop.
 You don't need a weatherman to know which way the wind blows.

Offline seanbarney41

  • not really that much younger than an
  • Really Old Timer ...
  • *******
  • Posts: 10,934
Re: Whats your favorite metal filler (minor pitting)
« Reply #3 on: April 01, 2021, 02:58:27 AM »
Sand it out with 40 grit.  You will have to sand the filler anyway.
Logged
If it works good, it looks good...

Offline CBJoe

  • Master
  • *****
  • Posts: 1,976
Re: Whats your favorite metal filler (minor pitting)
« Reply #4 on: April 05, 2021, 02:24:19 PM »
Thanks for responses all....i'll take a look at how deep the pitting is and go from there.
Logged
'07 Bonneville Black
'15 Moto Guzzi California 1400
CB750K2 Hot Rod Revival http://forums.sohc4.net/index.php/topic,171693.0.html
'65 CB77
'66 CM91 (C90'ish)

Offline Terry in Australia

  • Really Old Timer ...
  • *******
  • Posts: 33,407
  • So, what do ya wanna talk about today?
Re: Whats your favorite metal filler (minor pitting)
« Reply #5 on: April 05, 2021, 08:03:45 PM »
Spray putty Joe. Hit it with etch primer first, then spray on a few coats of spray putty, sand it smooth, prime and paint. Sometimes a couple of full wet coats of enamel will be enough to fill those pits, but spray putty will definitely do the job. ;D
Logged
I was feeling sorry for myself because I couldn't afford new bike boots, until I met a man with no legs.

So I said, "Hey mate, you haven't got any bike boots you don't need, do you?"

"Crazy is a very misunderstood term, it's a fine line that some of us can lean over and still keep our balance" (thanks RB550Four)

Online jgger

  • Master
  • *****
  • Posts: 2,384
Re: Whats your favorite metal filler (minor pitting)
« Reply #6 on: April 05, 2021, 10:09:51 PM »
Joe I thought you were talking about the "feet" on the center stand.  I don't think any kind of putty type filler would last long there. If itis wise where then you got several good suggestions. Now all you have to do now is pick one! Hahaha 😂
Logged
"The SOHC4 uses a computer located about 2-3 ft above the seat.  Those sometimes need additional programming." -stolen from  Two Tired

The difference between an ass kisser and brown noser is merely depth perception.  Stolen from RAFster122s
Pages: [1]   Go Up
« previous next »