Author Topic: Gaskets and seals (Read 24514 times)

Sam Green Racing · « **on:** January 16, 2012, 01:54:43 am »

NOTE TO ALL:

This thread details how one sohc4 member assembled and sold a Gasket/Seals set for the CB750A.

This member is Jim F. He made up a certain number of sets, and members agreed to purchase a set. All sets were shipped out the third/fourth quarter of 2012. Jim F can be reached at:

jfrench815@gmail.com

Has anyone got any surplus bottom end gaskets or seals (O rings ect) or know of any good suppliers or makers of gaskets.
I think I asked this some time back but can't find it, been through every thread on here.

Sam.

Sam Green Racing · « **Reply #1 on:** January 17, 2012, 02:07:20 am »

If we are able to get complete bottom end gasket sets made, who will want them.
Post your name in this thread and I'll start a list. I would think the more we have made, the better the price.

Sam.

Me...........................................................x2
POPS 911................................................X2
Kandrtech................................................X1
JWEEKS...................................................X2
Jonnycakes..............................................X1
Ndstrylgrnrngr.........................................X2
Vince08859 @ Hondachopper.................X1
MRieck.....................................................X1
05c50......................................................X1
tomsweb1...............................................X1
Charliedontsurf.......................................X1
Kate, Cycle One......................................X3 = 18 wanted.

raymond10078 · « **Reply #2 on:** January 17, 2012, 06:58:05 am »

I would buy a set.

jweeks · « **Reply #3 on:** January 17, 2012, 06:00:10 pm »

Sam,Bill,Jim,
I can never have enough! I'll take 2 sets.

Jon Weeks

Sam Green Racing · « **Reply #4 on:** January 18, 2012, 02:17:47 am »

Sorted Jonny, you're on the list.

Kandy, you lazy bugger, you have the POWER to put yourself on it.

Sam.

Sam Green Racing · « **Reply #5 on:** January 18, 2012, 07:13:36 am »

Good news guys, jonnycakes is lending his spare set to Jim F to have copied, big thanks Jonny.

Sam.

jonnycakes · « **Reply #6 on:** January 18, 2012, 09:57:56 am »

Put me in for one remanufactured "B" kits if they get made. Never hurts to have extras.

Sam Green Racing · « **Reply #7 on:** January 18, 2012, 11:49:17 am »

Will do Jonny.

Sam.

Grnrngr · « **Reply #8 on:** January 18, 2012, 11:53:38 am »

I'll take a pair...

jonnycakes · « **Reply #9 on:** January 18, 2012, 12:33:47 pm »

And Vince08859.hondachopper wants a set.

Sam Green Racing · « **Reply #10 on:** January 18, 2012, 03:04:32 pm »

Sorted Portland

and Vince.

Sam.

Grnrngr · « **Reply #11 on:** January 20, 2012, 04:20:28 pm »

Thanks for getting me on the list. If we can keep the cost down, might even want two more for my spare motors.

Sam Green Racing · « **Reply #12 on:** January 20, 2012, 05:13:36 pm »

I doubt it will be a problem, I think between us we can sort a few spares.

Sam.

05c50 · « **Reply #13 on:** January 22, 2012, 06:24:50 am »

I'll buy a set. Thanks

...........Paul

Sam Green Racing · « **Reply #14 on:** January 22, 2012, 06:53:59 am »

Gotcha Paul.

Sam.

hendrcs · « **Reply #15 on:** January 23, 2012, 02:56:12 pm »

Sam, I'm the one that authored that piece on Hondachopper.
I haven't confirmed it, but I think the 'matic oil pan gasket is the same as the early DOHC 750 (same part#) so those might be readily available.
It's the others that are so hard to find so I resorted to making my own.

Steve

Sam Green Racing · « **Reply #16 on:** January 23, 2012, 03:10:58 pm »

Thanks Steve, I will bare that in mind, thanks for the heads up.
We should hear something by the end of the week I think.

Sam.

Jim F · « **Reply #17 on:** January 24, 2012, 07:29:45 am »

I just got in the laser cut gaskets a little while ago and they look really good

I matched up the most complicated and its perfect
its not the same material but its a start

I have the set that Johnnycakes sent to me and I will be sending that up as soon as I get over to Bills
to check on how they fit up but I think they are going to be just fine.

Here is the OEM Gasket on top of the new one that was laser cut

Sam Green Racing · « **Reply #18 on:** January 24, 2012, 07:36:15 am »

How do we know the new one is under the old one, if it can't be seen, IT AINT THERE.

Can you post this in the gasket thread in the auto forum Jimmy, please ?

Sam.

MRieck · « **Reply #19 on:** January 24, 2012, 07:59:40 am »

Excellent work Jim.....you rule!

The only thing I see off a small bit is an indentation in the oil pump cut out (the large circle cut out). Or maybe that is an optical illusion.

Jim F · « **Reply #20 on:** January 24, 2012, 10:45:23 am »

Sam can you move it over to where it needs to go

Thats over my pay grade

thanks
Jim

Jim F · « **Reply #21 on:** January 24, 2012, 10:55:29 am »

Quote from: MRieck on January 24, 2012, 07:59:40 am

Excellent work Jim.....you rule! The only thing I see off a small bit is an indentation in the oil pump cut out (the large circle cut out). Or maybe that is an optical illusion.

I just checked it mike and it match,s good

jonnycakes · « **Reply #22 on:** January 25, 2012, 06:58:14 pm »

The part # for the "B" kit is 06111-393-000 . This way maybe someone goggling for this part number will find this thread.

Bill/BentON Racing · « **Reply #23 on:** January 26, 2012, 05:38:08 pm »

Well,Samauto needs one and so do I!!!!

Bill

Jim F · « **Reply #24 on:** January 30, 2012, 05:51:29 am »

Got the Laser cut gaskets over to Bills this weekend and he will check the fit on a motor

I sent the original set that Johnnycakes sent up to the laser cutter for deliver today
as soon as I hear from Bill about the fit, I will call the Laser cutter so he can start to measure the
thickness of each gasket and make a few sets
will keep all posted
Bill is looking into finding the "O" rings also
I will be doing the same

Jim

News:

Author Topic: Gaskets and seals (Read 24514 times)