Author Topic: Samauto II RC1080cc, RC crank and Golden rods, 327 cam etc, CB750 Automatic (Read 51925 times)

Bill/BentON Racing · « **on:** November 03, 2015, 02:21:49 PM »

I've started a new thread on Samauto II's transformation. Rear wheel has new tire, 630 rear sprocket and chain replaced with 530 setup. Rear wheel off a Suzuki GS750 or 1000. Rear wheel spins for 5 minutes! Wow! Bill
More later tonight.

Retro Rocket · « **Reply #1 on:** November 03, 2015, 02:30:07 PM »

Ceramic bearings...?

dragracer · « **Reply #2 on:** November 03, 2015, 02:37:25 PM »

About time you surfaced. I bet this is going to be good!!!!!!

Jerry Rxman Griffin aka MuthaF'er · « **Reply #3 on:** November 03, 2015, 04:36:17 PM »

Hey, just get some dyno time and SOON LOL

I'll be tuned in Bro Bling.

Bill/BentON Racing · « **Reply #4 on:** November 03, 2015, 06:14:40 PM »

I been busy busy!!

dragracer · « **Reply #5 on:** November 03, 2015, 06:16:12 PM »

Jerry, when are you arriving in Atlanta??? And leave Billy Bling alone. You know how he rolls.

Bill/BentON Racing · « **Reply #6 on:** November 03, 2015, 06:17:41 PM »

A couple more pics.

Jerry Rxman Griffin aka MuthaF'er · « **Reply #7 on:** November 03, 2015, 07:20:25 PM »

Looking good Bill! Keep up the hard work and posts.

Frank, I'll be in ATL Monday.

754 · « **Reply #8 on:** November 03, 2015, 08:39:20 PM »

Is that a 3. Or 3.5 Sun rim ?

dragracer · « **Reply #9 on:** November 03, 2015, 10:03:51 PM »

Quote from: Bill/BentON Racing on November 03, 2015, 06:17:41 PM

A couple more pics.

Keep it movin man!! You're getting there. Lots to do and not much time left.

At some point, the two of us need to stop this last minute crunching, get our equipment together early so we can be relaxed when we get to the track. We're not getting any younger and these long days/nights picking at these bikes takes a toll on an old mans's body. Eventually it shows at the track on race day and not in a positive way.

Is that a DRL300 limiter??

gschuld · « **Reply #10 on:** November 04, 2015, 05:24:34 AM »

Quote from: dragracer on November 03, 2015, 10:03:51 PM

Quote from: Bill/BentON Racing on November 03, 2015, 06:17:41 PM
A couple more pics.

Is that a DRL300 limiter??

Sure looks like it. Billy are you running a 130 or 140 series rounded section tire on that bike? Holy smokes, that's a lot of motor and chassis being thrown at such a modest tire contact patch... your a brave man.

George

Bill/BentON Racing · « **Reply #11 on:** November 04, 2015, 07:07:42 AM »

Man, I wish I had a 17 , next year I will! But no, it's a 150/60×18, but has internal rim locks, I'll post a pic. And still has at least 50 psi plus when pic was taken from seating bead.

. But, I hear you! K, Bill So I can run lower pressures and get mo contact patch.

gschuld · « **Reply #12 on:** November 04, 2015, 07:13:53 AM »

What width rim are you running it on? That would make a big difference on how flat the tire crown will be. If your on a 3.5x18 rim, you might be stuck with a fairly tall and narrow profile. Oh that was the BT45 tire that you picked up recently?

George.

MRieck · « **Reply #13 on:** November 04, 2015, 08:40:10 AM »

You need some of my updated stickers Bill.

gschuld · « **Reply #14 on:** November 04, 2015, 09:16:36 AM »

Oh you noticed too...

Bill/BentON Racing · « **Reply #15 on:** November 04, 2015, 12:49:28 PM »

Me too, Mike, please send me some more, I knew it was an old email address , but I wanted your name on it!
Feank, it's a Sun rim 3.50 x 18.George, thanks for sending carbs back for Valdosta, Bill

Bill/BentON Racing · « **Reply #16 on:** November 04, 2015, 02:10:54 PM »

More pics.

Stev-o · « **Reply #17 on:** November 04, 2015, 04:54:16 PM »

Quote

You need updated stickers...

Have never seen Action Four stickers. [have the exhaust on my K4]

Bill/BentON Racing · « **Reply #18 on:** November 04, 2015, 05:22:13 PM »

Some of us are ancient!!

jweeks · « **Reply #19 on:** November 04, 2015, 06:39:43 PM »

Rear brake setup? Pictures? Does it run?

Bill/BentON Racing · « **Reply #20 on:** November 04, 2015, 06:45:35 PM »

What, you think it's Christmas? Ain't giving away my secrets, ok a couple pics!! Haha.Lol

edwardmorris · « **Reply #21 on:** November 05, 2015, 07:50:02 AM »

Rear wheel

jweeks · « **Reply #22 on:** November 06, 2015, 04:21:03 PM »

I've tried that rear brake setup. I'm up to high 11's estimated best using it. I suspect that the bike will pull through the rear brake pressure with the right cam and converter. This is sounding more and more like a slow off the line, top end strong bike. Good luck with this one. You definitely need some test and tune time to sort out the launch. I just hope that the fiber clutches are mostly there. If they are badly worn, you'll find a slipping clutch on launch and/or at the gear shift. Good luck!

dragracer · « **Reply #23 on:** November 06, 2015, 07:48:21 PM »

Bill will be a busy man testing both bikes on next Friday at SGMP. 10am to 3pm should be long enough as long as there are no problems to sort out. And then the one time run after 4pm that evening to round things out. Personally I'd double enter and ride both bikes myself.

POPS 911 · « **Reply #24 on:** November 07, 2015, 10:56:36 AM »

jweeks: You run rear shocks or struts on your 10 second Hondamatic SOHC 750 based ST/ET drag bike ?

News:

Author Topic: Samauto II RC1080cc, RC crank and Golden rods, 327 cam etc, CB750 Automatic (Read 51925 times)