Author Topic: Project Learning Curve (Read 6232 times)

mbryan · « **Reply #25 on:** May 10, 2020, 07:29:01 AM »

How about these?

https://www.dropbox.com/s/i7oypj1z88kjqgp/20200509_114320.jpg?dl=0

mbryan · « **Reply #26 on:** May 10, 2020, 07:50:20 AM »

When I click on the link sometimes it will show the pic briefly then I get a popup showing a log in screen.....I just hit the X at the top right to make it go away. Here are some more.....let me know if they work please.

[https://www.dropbox.com/s/npxtrwk31fnw3qu/20200509_152513.jpg?dl=0]

https://www.dropbox.com/s/fjz1tjgohkn8l46/20200508_152218.jpg?dl=0

flatlander · « **Reply #27 on:** May 10, 2020, 09:50:09 AM »

now i can see them, thanks. no pics of the jets but i would trust cal's eyes on that.

mbryan · « **Reply #28 on:** May 11, 2020, 07:38:50 AM »

Do you guys know where I can get a set of tappet cover seals? The covers are fine.....looks like the seals need replacing though.

flatlander · « **Reply #29 on:** May 11, 2020, 07:59:39 AM »

cmsnl or davidsilverspares have OEM stuff. or look up the part number in the partslist and stick in google, then you get all sorts of hits.
for these kind of things i normally buy OEM as those fit best and last longest.

mbryan · « **Reply #30 on:** May 12, 2020, 07:07:56 PM »

ok.....the good.... started to clean the carbs tonight with my son. Got the kit from 4 into 1. Has bowl gasket, top gasket, float neadle, and various round gaskets. All going well except I think the carb cleaner got to me a bit (had a fan on but still ......wow).

https://photos-1.dropbox.com/t/2/AACeJl0TLw-zoT1-rsXbjwl0vCnWm7dHIS3UX4BD1Uk45g/12/3159652576/jpeg/32x32/1/1591927200/1/9/20200512_194843.jpg/EIDkm6kcIAooCg/BdBQcY1wWysXSAg4_vWDY7tkyvnKoMJYzSKjvTXIc-qnW1BQurW4_5S6sCdX2ToW2nmbn9gO6-3JffmxA9SHnfP-XrVIKPkYJkvG1vtsDk59fuQXU-VP8-_9E6ZFfEyH0Lc?size=32x32&size_mode=2

The not so good.......when taking the components apart, I noticed that fuel mixture screw washer and gasket on carb 3 is not there.....and the kit does not have a washer (it does have a gasket though)......and it is the size of an atom so I cant find it!!!!

https://previews.dropbox.com/p/thumb/AAywqT_YtF4mTqV8AeQZ150yvKdGao7YhdwWBDMcXrLTTe4Rtr0D5VQzSH0BkiK4zconAR8LgTFvtdBvD7CgnPAskGO906uksLXv_QSRs1GdPIbJZyNBcOiJRpuFQuEF6FRXR13rdI01rQDpmZPUrFcpcU8mv4hN7uf9uw9kCQ2VRs2iGK88FfYEiPZjzqviuUbKEPn3wkrY-0nm-ZRl-Cn-4i8zIrXMM9rJcgJKTov_PK2NXJ5K6zxFNRBUMkvj-L295dN6EaPTSSqGrCJQOEXMok8J0l41imV8nO57ovszHr1omDhkLIpaZrj8we0i623ju56FsGkmsDB8Ei5RMcYnbhEu8_gj4NPzqqSwqSUzkg/p.jpeg?fv_content=true&size_mode=5

Soooooo......anyone know where I can get this one washer.....or 4 of them....or?

We wanted to try to clean them, set them up, and try to install them to see if the bike would at least start (have not been able to do that yet)

mbryan · « **Reply #31 on:** May 12, 2020, 07:16:12 PM »

Well.....those pics are not working....again.....try this.

https://www.dropbox.com/s/ooctsrovpmzsayo/20200512_194843.jpg?dl=0

https://www.dropbox.com/s/glu4cqwosg8r712/20200512_194936.jpg?dl=0

mbryan · « **Reply #32 on:** May 13, 2020, 05:41:40 AM »

Found the part(s) at David Silver

https://www.davidsilverspares.com/parts/by-part-number/partnumber_4951/

will order 2 to be sure I have enough.....or to say it another way.....in case I loose one again!!

Looks like my oil leak is coming from the cam cover/tappet area. The bike sits on its kick stand (I dont have a stand to sit it upright yet) and even not running the oil will pool at the top of the head on the first fin which is where gravity will bring it in this position. I will get a top end gasket set and see if just changing those very top end gaskets will help.

flatlander · « **Reply #33 on:** May 13, 2020, 06:15:07 AM »

if oil gets on the top fin, a pretty likely cause is from the cam shaft end cap. there are 2 o-rings on the studs that keep the end cap located in the rocker shaft holes. and there's a bracket that the cap is screwed on to. there are washers on the bolt keeping the bracket in place, check the partslist for that. the washers need to be sealing ones, e.g. from copper.

mbryan · « **Reply #34 on:** May 13, 2020, 06:46:18 AM »

Got it.....one question about putting that cover back on( I was going to get a kit and replace the breather cover and cam cover gaskets). I see on the service manual it shows to torque the bolts to 6-9 ftlbs .....how about the screws on top? My motor has a combination of JIS screws and bolts holding all of it down.

mbryan · « **Reply #35 on:** May 13, 2020, 08:28:05 AM »

well.....I got everything (for now) except that copper washer. I think it is this one...

https://www.cmsnl.com/honda-cb550k-1978-usa_model7222/washer-65-mm_90485001000/#.XrwRQmhKiUk

I looked here and at David Silver and babbits.....will keep looking.

flatlander · « **Reply #36 on:** May 13, 2020, 08:42:01 AM »

any 6mm copper washer will do. it doesn't have to be OEM honda.
the honda ones are actually more fancy, i don't remember what exactly - maybe brass coated with zinc? but copper works fine there, and is easier and cheaper to get. also on the rocker cover, those bolts that have oil behind them need sealing washers so better just get a few of them.

the bolts holding down the rocker cover:
i'd replace the jis with allen heads. be careful with torque on all 6mm bolts that go into alu on these blocks. it's very easy to strip the threads, especially with a torque wrench. it's enough to carefully nip them tight by hand.

mbryan · « **Reply #37 on:** May 13, 2020, 04:30:19 PM »

Will do......

Another question.....I see some people have used a polish on a q-tip and used that to polish the seats in the carburetor.....float seat and fuel mix seat. Opinions on that.....and if good to go can you point me to a polish?

flatlander · « **Reply #38 on:** May 13, 2020, 11:06:09 PM »

why do you want to do that? do the carbs leak?
if not, i'd just clean them up, put them back together and see how they do.

mbryan · « **Reply #39 on:** May 14, 2020, 05:21:54 AM »

Fair enough.....was just trying to do all the good things that should be done while they are apart, but I see your point.

On a side note.....my son cleaned the engine up yesterday with carb cleaner and some degreaser. Got heavy handed and now the finish is etched on the aluminum and some pait is missing. Oh whell, learning moment. Will add that to the list of things to repair.

calj737 · « **Reply #40 on:** May 14, 2020, 07:34:48 AM »

Don't fret. The engine is aluminum and all he's done is remove the oxidation that existed. It Weill return very quickly.

Going forward, use stainless steel brushes (you can get them at Harbor Freight, etc) to brush, scrub and clean the cases with. They remove the oxidation and don't scratch the aluminum. Avoid high pH cleansers too. These will turn the ally grey. There are aluminum specific/tolerant cleansers out there that work well.

Lastly, use a variety of ScotchBrite pads to put a finish on the parts after they're degreased. Carb cleaner is a decent choice for cleaning because it has an anti-oxidant in it unlike Brake Cleaner. Diesel fuel works great too, but its a bit messy.

mbryan · « **Reply #41 on:** May 14, 2020, 11:51:22 AM »

Got it.....thanks.

So after cleaning and drying over night I went and looked and so far no oil.....again I have not run this bike at all and was getting some seepage along the downward fins as it sat on the side stand. Also, I think I mentioned this.....but while I was poking around u noticed a bolt loose. It is the one on the head between the two and three exhaust pipes in the pic. I snuggled it pretty good. I wonder if that was my source? Doesn't explain the top fin though.

https://www.dropbox.com/s/o3qllrk70ijs3y1/20200514_134105.jpg?dl=0

Lastly.....do you know what type of handle bars are these? Not stock as the wires are not through the handles....and not clip on' as I have learned.

https://www.dropbox.com/s/946asmvvi4ftf8h/20200514_134044.jpg?dl=0

Thanks

calj737 · « **Reply #42 on:** May 14, 2020, 12:30:27 PM »

Look like Norman Hyde or Euro bars

mbryan · « **Reply #43 on:** May 16, 2020, 08:07:42 AM »

So digging around the box of parts that came with the bike we found this. (we were looking for the center stand)

https://previews.dropbox.com/p/thumb/AAyk_axcnXowy-GYZhCGRflgAX-GJSDOS2jG_NDg6qPAB1FB7u8uZnwlm-GkepukjfIUSqtbfdYqOWm20tGwnSXP9rl_-jSdjrr-hkSZSmWNfQ6Ey0SbRdXu2lFZLH8IEhh88m-2L3jVDx7N9bbMHZz36N68Kmor9bkxnm9idWZHd5vZrSEIPR4nq-_Z-C43IAYk0WL6Vw4p7TfcRUpfMFpas2erU-N4bVmYqyLJZv-uV51479ItwR1223i_jBD5XVdTaZ2AmH80DOSBlZJFZ8rf8EQHQXPoCNME51WMr0fG6hJNqITqvexhZ4BDFwdNTKJE0iM3VXYwVQa6TGQOMI5QjphRl4Rr1e6GBcpbzfgr2Q/p.jpeg?fv_content=true&size_mode=5

Does anyone know what it is?

MauiK3 · « **Reply #44 on:** May 16, 2020, 09:22:10 AM »

Seems the link is top secret

mbryan · « **Reply #45 on:** May 16, 2020, 09:25:48 AM »

Can't seem to get this right.....try this...

https://www.dropbox.com/s/0gzzjh2h4o21cni/20200515_155451.jpg?dl=0

flatlander · « **Reply #46 on:** May 16, 2020, 12:31:45 PM »

i am sorry to tell you but that is not the centre stand

no clue what that's meant to be. doesn't look like anything that belongs to a 550.

Robbo · « **Reply #47 on:** May 16, 2020, 01:14:58 PM »

Do those channels align with the downtubes of the frame at the front of the motor? Could be for a fairing with some sort of engine protector. Looks homemade

Sent from my iPhone using Tapatalk

mbryan · « **Reply #48 on:** May 16, 2020, 02:25:11 PM »

It does look homemade.

Dont know about yall......but this makes me smile

https://www.dropbox.com/s/7r2bz0pmt6ye37d/20200516_162100.jpg?dl=0

Robbo · « **Reply #49 on:** May 16, 2020, 03:10:02 PM »

Quote from: mbryan on May 16, 2020, 02:25:11 PM

It does look homemade.

Dont know about yall......but this makes me smile

https://www.dropbox.com/s/7r2bz0pmt6ye37d/20200516_162100.jpg?dl=0

Nice to see the concentration

(Or did you mean that the angle of the screwdriver looked like the fuel gauge indicator for his t-shirt) LOL

Sent from my iPhone using Tapatalk

News:

Author Topic: Project Learning Curve (Read 6232 times)