Author Topic: Billet blocks....who will pay...pics added 9/7/09...10/24....2/10 (Read 191343 times)

MRieck · « **Reply #425 on:** May 07, 2010, 04:36:49 AM »

Quote from: bwaller on May 06, 2010, 07:30:11 PM

I went back a few pages where you sat your NOS head on the new block and the fit looks better than the original.

Mike would you mind giving us another shot down the hole of the plating?

Sure Brent.

mick7504 · « **Reply #426 on:** May 11, 2010, 04:12:15 AM »

Mike
I thankyou sir.
This arrived at the Post office this morning and is nothing short of perfect.
72mm MTC pistons and Billet Block finished to utmost precision.
Mick

andy750 · « **Reply #427 on:** May 11, 2010, 04:34:01 AM »

Great photos Mick! Cant wait to see the finished bike!
Good luck!
Andy

Sam Green Racing · « **Reply #428 on:** May 11, 2010, 04:43:14 AM »

If that was in the Babe thread it would be deleted, pure PORN.

Sam.

voxonda · « **Reply #429 on:** May 11, 2010, 04:57:07 AM »

Man, if only I could afford this treasure!

mick7504 · « **Reply #430 on:** May 11, 2010, 04:58:25 AM »

Thanks Andy and Sam.
I'm just over the bloody moon with this.
It will take some time to get this project all together.
APE is doing some work on the crank and tranny and supplying new rods and Mike is working on the head.
This is a grass roots up build with no shortcuts.
There's nothing like being a kid at Xmas again and that's how it is right now.

Mick

mick7504 · « **Reply #431 on:** May 11, 2010, 05:04:17 AM »

Quote from: voxonda on May 11, 2010, 04:57:07 AM

Man, if only I could afford this treasure!

Hey Rob
Someway, somehow it can happen.
I really didn't think that it would all come to fruition but my heart and my guts said to just do it.
I will never look back on this decision.
Mick

voxonda · « **Reply #432 on:** May 11, 2010, 05:14:52 AM »

Quote from: mick7504 on May 11, 2010, 05:04:17 AM

Quote from: voxonda on May 11, 2010, 04:57:07 AM
Man, if only I could afford this treasure!
Hey Rob
Someway, somehow it can happen.
I really didn't think that it would all come to fruition but my heart and my guts said to just do it.
I will never look back on this decision.
Mick

Hey Mick,

That is the spirit, stick to your decision and don't look back.

Rob

Ecosse · « **Reply #433 on:** May 11, 2010, 11:00:55 AM »

Quote from: SamCB750A on May 11, 2010, 04:43:14 AM

If that was in the Babe thread it would be deleted, pure PORN.

+1

bwaller · « **Reply #434 on:** May 11, 2010, 08:08:48 PM »

Yes good pics Mick, top shelf.

Retro Rocket · « **Reply #435 on:** May 11, 2010, 11:00:02 PM »

Awesome Mick, mine should be here soon.....

Can't wait.....

Mick

MRieck · « **Reply #436 on:** May 12, 2010, 07:27:53 PM »

Quote from: retro rocket on May 11, 2010, 11:00:02 PM

Awesome Mick, mine should be here soon..... Can't wait.....

Mick

It will be Mick. I have to oring the cylinders which, if never done it, sucks in general.

Retro Rocket · « **Reply #437 on:** May 12, 2010, 07:30:19 PM »

Quote from: MRieck on May 12, 2010, 07:27:53 PM

Quote from: retro rocket on May 11, 2010, 11:00:02 PM
Awesome Mick, mine should be here soon..... Can't wait.....

Mick
It will be Mick. I have to oring the cylinders which, if never done it, sucks in general.

Thats cool Mike, there's no rush.....just mild anxiety....

Mick

Jerry Rxman Griffin aka MuthaF'er · « **Reply #438 on:** May 12, 2010, 08:32:04 PM »

You boys over in the corner whacking off?

(I'm jealous)

754 · « **Reply #439 on:** May 12, 2010, 09:37:49 PM »

You bead blasted them, as opposed to a machined finish??

mick7504 · « **Reply #440 on:** May 12, 2010, 10:07:21 PM »

Quote from: 754 on May 12, 2010, 09:37:49 PM

You bead blasted them, as opposed to a machined finish??

I believe that they were blasted by Millenium after they were bored.
Mike could confirm this.
Mick

BLUE71TURBO · « **Reply #441 on:** May 12, 2010, 10:07:54 PM »

Quote from: 754 on May 12, 2010, 09:37:49 PM

You bead blasted them, as opposed to a machined finish??

It sure looks like he did. I'd prefer the fresh machined look myself. I like shiny.

Retro Rocket · « **Reply #442 on:** May 12, 2010, 10:21:55 PM »

Mines getting ceramic coated so no problems here....

Mick

MRieck · « **Reply #443 on:** May 13, 2010, 04:54:57 AM »

Quote from: BLUE71TURBO on May 12, 2010, 10:07:54 PM

Quote from: 754 on May 12, 2010, 09:37:49 PM
You bead blasted them, as opposed to a machined finish??

It sure looks like he did. I'd prefer the fresh machined look myself. I like shiny.

Me too BUT It is impossible to maintain the machined, shiny finish. Even if Millennium does not blast it they etch the cylinder to promote adhesion. The cylinder comes out looking milky white. They have to be bead blasted to look decent.

Sam Green Racing · « **Reply #444 on:** May 13, 2010, 05:08:25 AM »

Who got number 6 Mike, or is it a secret

Sam.

Jerry Rxman Griffin aka MuthaF'er · « **Reply #445 on:** May 13, 2010, 10:03:15 AM »

Better yet Michael, how's your 1000 coming along??

BLUE71TURBO · « **Reply #446 on:** May 13, 2010, 10:18:47 AM »

Quote from: MRieck on May 13, 2010, 04:54:57 AM

Quote from: BLUE71TURBO on May 12, 2010, 10:07:54 PM
Quote from: 754 on May 12, 2010, 09:37:49 PM
You bead blasted them, as opposed to a machined finish??

It sure looks like he did. I'd prefer the fresh machined look myself. I like shiny.
Me too BUT It is impossible to maintain the machined, shiny finish. Even if Millennium does not blast it they etch the cylinder to promote adhesion. The cylinder comes out looking milky white. They have to be bead blasted to look decent.

Thats why when I am able to get mine I'm gonna use sleeves so the cylinder block will retain the nice shiny milled billet look.

Matt Hubbell · « **Reply #447 on:** May 17, 2010, 11:03:10 AM »

Flat or shiny, I was there yesterday in Mike's secret underground laboratory and I am here to say, these things are not just billet engine blocks, as they qualify for motorcycle art.

Ecosse · « **Reply #448 on:** May 17, 2010, 01:30:35 PM »

it's settled then! to do mike's work justice a whole engine assembly is a must.

besides, a modern gearbox with six speeds and more strength is only right.

754 · « **Reply #449 on:** May 18, 2010, 08:38:46 AM »

Sounds like you can still polish up the fins after the etch process..

News:

Author Topic: Billet blocks....who will pay...pics added 9/7/09...10/24....2/10 (Read 191343 times)